• Computers and Concrete
• /
• 제20권3호
• /
• pp.329-338
• /
• 2017

A new simple and practical strut-and-tie model (STM) for predicting the shear strength of RC pile caps is proposed in this paper. Two approaches are adopted to take into account the concrete softening effect. In the first approach, a concrete efficiency factor based on compression field theory is employed to determine the effective strength of a concrete strut, assumed to control the shear strength of the whole member. The second adopted Kupfer and Gerstle's biaxial failure criterion of concrete to derive the simple nominal shear strength of pile caps containing the interaction between strut and tie capacity. The validation of these two methods is investigated using 110 RC pile cap test results and other STMs available in the literature. It was found that the failure criterion approach appears to provide more accurate and consistent predictions, and hence is chosen to be the proposed STM. Finally, the predictions of the proposed STM are also compared with those obtained by using seven other STMs from codes of practice and the literature, and were found to give better accuracy and consistency.

• 터널과지하공간
• /
• 제22권6호
• /
• pp.393-402
• /
• 2012

정상부가 개착된 암반사면에 지중경사계를 설치하여 개착사면의 내부 거동을 계측하였으며, 국지적으로 배후면 방향으로의 거동이 관찰되었다. 사면 거동, 특히 배후면 방향으로의 거동을 유발시키는 원인을 분석하기 위하여 시추작업을 수행하였다. 추출된 시추코어를 관찰하여 사면 암반의 암석학적 취약성을 조사하였으며, 공내 BIPS 영상을 취득하여 암반의 구조적 특성을 분석하였다. 코어 절리 시료를 이용하여 불연속면의 역학적 특성을 측정하였으며, 탄질물이 협재된 절리 시료에 대한 직접전단시험을 수행하여 전단강도를 측정하였다. 사면 거동에 대한 계측결과를 사면 암반과 탄질물이 협재된 절리들의 구조적 및 역학적 특성을 종합적으로 고려하여 해석하였으며, 절리에 협재된 탄질물 및 팽윤성 점토광물의 존재에 의해 국지적인 사면거동이 지배될 수 있는 잠재성을 확인하였다.

• Steel and Composite Structures
• /
• 제22권5호
• /
• pp.1019-1038
• /
• 2016

The use of high-strength concrete (HSC) in precast concrete segmental bridges (PCSBs) can minimize the superstructure geometry and reduce beam weight, which can accelerate the construction speed. Dry joints between the segments in PCSBs introduce discontinuity and require special attention in design and construction. Cracks in dry joints initiate more easily than those in epoxy joints in construction period or in service. Due to the higher rupture strength of HSC, the higher cracking resistance can be achieved. In this study, shear behavior of dry joints in PCSBs was investigated by experiments, especially focusing on cracking resistance and shear strength of HSC dry joints. It can be concluded that the use of HSC can improve the cracking resistance, shear strength, and ductility of monolithic, single-keyed and three-keyed specimens. The experimental results obtained from tests were compared with the AASHTO 2003 design provisions. The AASHTO 2003 provision underestimates the shear capacity of single-keyed dry joint C50 and C70 HSC specimens, underestimates the shear strength of three-keyed dry joint C70 HSC specimens, and overestimates the shear capacity of three-keyed dry joint C50 HSC specimens.

• Journal of the Korean Wood Science and Technology
• /
• 제39권5호
• /
• pp.429-436
• /
• 2011

The selected physical and mechanical properties of non-certificated LVL circulated in domestic lumber market were investigated and compared to relevant standards. The tested LVL passed the moisture content and the soaking delamination rate limit as per domestic (KS) and Japanese standard (JAS). The evaluated mechanical properties were flatwise/edgewise bending strength, modulus of elasticity (MOE), horizontal shear and compressive strength. The 30 mm-thick LVL showed significantly higher bending strength than that of the 25 mm-thick LVL. The modulus of elasticity (MOE) showed same tendency in the results of bending strength. The edgewise bending strength and MOE were higher than that of flatwise bending strength and MOE. The horizontal shear strength values were also showed similar results to bending strength values. The tested results were compared each other and each products were graded according to JAS 701 grade specification. The failure mode of LVL in bending test showed the similar failure mode of solidwood that failed in a simple tension manner (splintery tension). The glue line failure was severe in 25 mm-thick specimens due to concentration of shear stress in layer discontinuity containing small voids and starved glue lines. In horizontal shear strength test, failure mode of LVL showed the typical horizontal shear failure. Compressive specimens failed with fiber crushing in company with apparent delamination that splitted along the length of the specimens. From the results, the complete bonding between lamination and consistency in thin veneer layer were considered as a critical factor in the mechanical properties of LVL. Moreover, the standard test procedure and specification for non-certificated LVL should be required to check the performance of uncertificated materials.

• Geomechanics and Engineering
• /
• 제13권4호
• /
• pp.535-570
• /
• 2017

There are only few cases where cause and location of failure of a rock structure are limited to a single discontinuity. Usually several discontinuities of limited size interact and eventually form a combined shear plane where failure takes place. So, besides the discontinuities, the regions between adjacent discontinuities, which consist of strong rock and are called material or rock bridges, are of utmost importance for the shear strength of the compound failure plane. Shear behaviour of persistent and non-persistent joint are different from each other. Shear strength of rock mass containing non-persistent joints is highly affected by mechanical behavior and geometrical configuration of non-persistent joints located in a rock mass. Therefore investigation is essential to study the fundamental failures occurring in a rock bridge, for assessing anticipated and actual performances of the structures built on or in rock masses. The purpose of this review paper is to present techniques, progresses and the likely future development directions in experimental testing of non-persistent joint failure behaviour. Experimental results showed that the presence of rock bridges in not fully persistent natural discontinuity sets is a significant factor affecting the stability of rock structures. Compared with intact rocks, jointed rock masses are usually weaker, more deformable and highly anisotropic, depending upon the mechanical properties of each joint and the explicit joint positions. The joint spacing, joint persistency, number of rock joint, angle of rock joint, length of rock bridge, angle of rock bridge, normal load, scale effect and material mixture have important effect on the failure mechanism of a rock bridge.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.494-505
• /
• 2006

In this study, using constant normal stiffness(CNS) direct shear tests, side shear load distribution were analyzed by the influencing parameters of unconfined compressive strength, surface roughness, confining stress, and material properties. Based on the CNS tests, side shear load transfer function of drilled shafts in rock is proposed using geological strength index(GSI), which indicates discontinuity and surface condition of rock mass in Hoek-Brown criterion. Though comparisons with results of nine drilled shafts's load tests, it is found that the load-transfer curve by this study is in good agreement with the general trend observed by in situ measurements, and thus represents a significant improvement in the prediction of bearing capacity of drilled shaft.

• 한국레이저가공학회지
• /
• 제3권3호
• /
• pp.31-37
• /
• 2000

In this paper, the possibilities of the laser overlap spot welding were studied to utilize the advantageous properties of amorphous metal foils. In order to estimate the usage of amorphous metals foils as structural members, the tensile shear strength and the fracture features were investigated. Although the crystalline zone on the surface was formed, it was not the direct cause of the fracture of the weld. The fracture of the weld resulted from the geometry discontinuity between the workpiece and the protrusion zone, which was formed during the weld process. The vein pattern - the typical feature of the fracture of the amorphous metal - was formed on the fracture surface. The tensile shear stress was reached to 1200 N/㎟ (2-foils overlap welding) and 900 N/㎟ (10-foils overlap welding), whereas the tensile strength of the workpiece was 1500-2000 N/㎟.

• 한국지반신소재학회논문집
• /
• 제21권2호
• /
• pp.21-30
• /
• 2022

전단강도는 암반 비탈면 안정성 평가에서 가장 중요한 지표이다. 일반적으로 기존 문헌자료, 역해석, 실험 등의 결과를 비교하여 산정한다. 암반 비탈면에서의 전단강도는 불연속면의 상태와 관련된 변수를 추가로 고려해야 한다. 이 변수들은 시추조사를 통해 여부를 파악하는 것이 어려울뿐더러 전단강도와의 정확한 관계를 찾아내기도 어렵다. 본 연구에서는 역해석을 통해 산정된 데이터를 이용했다. 기존 고려되었던 변수들의 관계를 딥러닝에 접목시켜 전단강도 산정에 적합한지 그 가능성을 모색하였다. 비교를 위해 기존에 사용되는 간단한 선형회귀(Linear Regression) 모델과 딥러닝 알고리즘인 심층인공신경망(DNN) 모델을 사용하였다. 각 분석 모델은 비슷한 예측결과를 도출해내었지만 미세한 차이로 DNN의 설명력이 개선된 결과를 나타내었다.

• 지질공학
• /
• 제34권2호
• /
• pp.317-327
• /
• 2024

대규모 암반 사면에서 비연속성의 절리계가 발달할 때, 계단상 활동면에 의한 사면 파괴가 발생할 수 있다. 계단상 활동면은 절리-절리 활동면 또는 절리-암교 활동면으로 구분할 수 있으며, 절리-암교 활동면에서 암교는 절리와 평행한 전단 저항과 절리에 수직인 인장 저항을 제공한다. 계단 경로 파괴는 활동 암괴의 하중에 의해 암교의 파괴가 발생하여 암교 양단의 두 절리가 연결되며 발생한다. 암교의 길이가 동일하다면 암석의 인장강도가 전단강도에 비해 낮으므로 절리에 수직으로 형성된 암교가 파괴에 취약하며, 불연속면 간격/길이의 비가 작을수록 계단 경로 파괴의 가능성이 커진다. 비연속성의 절리가 발달하는 암반 사면의 계단상 활동 파괴 위험에 대한 평가를 위해서는 체계적인 불연속면 조사 및 분석을 통해 계단 경로 파괴면을 구성하여 한계 평형 해석 또는 수치 해석 등의 안정성 평가를 수행하여야 한다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.865-872
• /
• 2006

Recently, many apartment buildings in the shear wall system often has pilotis in the lower story to meet the architectural needs. If the lateral force resisting system consists of shear walls supported by columns and beams. the discontinuity at the lowest level with pilotis results in the vertical irregularity with strength and stiffness. So, there are needs to be considered tile analysis and design about column and beam bellow shear walls and the behavior and stress condition of structure by stiffness change being generated at shear walls. The purpose of this paper is to investigate the behavior of shear wall structures with pilotis using the floors modeled as rigid diaphragm or semi rigid diaphragm. Through analyses, after estimating values of the story drift, natural period, stress condition of shear walls and the forces of column, we inferred how the behavior of shear wall structures with pilotis was influenced by the floor stiffness.