• Korean Journal of Organic Agriculture
• /
• v.9 no.3
• /
• pp.23-44
• /
• 2001

To address complex solutions to tack1e the cost rise with the increasing of the prices of crude oil, and to lower warming gas discharge in agricultural sector in line with the framework Convention on Climate Change, we need to net only develop the methods of simply reducing energy use ratio, but also effectively energize resources discharged in the course of agricultural production aimed at enabling repealed farming, and develop systems to reinvest such energy into agricultural production and apply them to actual farming. To that end, specifically, we need to reduce the energy cost in agricultural production, and produce and harness bio gas that makes it possible to stabilize the continued supply of energy. Thus, in this research, we seek to discuss energy use volume and warming gas discharge, and the characteristics of bio gas and its use methods alike, in agricultural sector, and thus present methods for environment-friendly and continual development in agriculture.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.3
• /
• pp.174-177
• /
• 2003

Electric double-layer capacitors based on charge storage at the interface between a high surface area activated carbon electrode and an electrolyte solution are characterized by their long cycle-life and high power density in comparison with batteries. However, energy density of electric double-layer capacitors obtained at present is about 6 Wh/kg at a power density of 500W/kg which is smaller as compared with that of batteries and limits the wide spread use of the capacitors. Therefore, a new capacitor that shows larger energy density than that of electric double-layer capacitors is proposed. The new capacitor is the hybrid capacitor consisting of activated carbon cathode, carbonaceous anode and an organic electrolyte. Maximum voltage applicable to the cell is over 4.2V that is larger than that of the electric double-layer capacitor. As a result, discharged energy density on the basis of stacked volume of electrode, current collector and separator is more than 18Wh/l at a power density of 500W/l.

• Journal of Trauma and Injury
• /
• v.19 no.1
• /
• pp.41-46
• /
• 2006

Purpose: Hypovolemia is not uncommon among trauma patients in the emergency department (ED). Successful resuscitation of a hypovolemic patient often requires rapid intravenous administration of massive amounts of fluid. A rapid fluid infuser is used in the ED for this purpose, there have been no studies of their clinical uses and effectiveness. We studied clinical experience with a rapid fluid infuser at an urban university hospital in Seoul, Korea. Methods: We reviewed the medical records of 38 patients admitted to the ED with a history of application of a rapid fluid infuser from January 2004 to July 2005. Adult trauma patients older than 15 years of age were included in this study. Clinical data on the patients and the volume of fluid used to achieve a stable blood pressure were extracted from their medical records. Results: The total number of adult trauma patients with a history of application of a rapid fluid infuser from January 2004 to July 2005 in the ED was 16. The mean systolic blood pressure for deciding to apply the rapid fluid infuser was $74.9{\pm}12.7mmHg$. The mean time and volume used to achieve a stable blood pressure were 40.4 min and$2947.3{\pm}1339.2ml$, respectively. In all patients, the amount of fluid infused before using the rapid fluid infuser was between 500 ml and 10,000 ml, compared to 1,000 ml and 6,200 ml with the rapid fluid infuser. The mean amount of fluid per min. via the rapid fluid infuser was 85.5 ml. Vital signs were stabilized in 11 patients, 6 of the 11 were discharged alive. Conclusion: The mean amount of fluid delivered per min. via the rapid fluid infuser was much less than expected; thus, there should be clinical guidelines on volume resuscitation with a rapid fluid infuser in the ED. In the future, prospective, multicenter, clinical-data collection is needed for a more sophisticated study.

• Perspectives in Nursing Science
• /
• v.17 no.2
• /
• pp.90-98
• /
• 2020

Purpose: This study examined the effects of breastfeeding education among preterm mothers. Methods: A nonequivalent control group, repeated measure, quasi-experimental study design was used. The participants comprised 46 preterm mothers recruited from the neonatal intensive care unit of a university hospital who were divided into two groups: 23 in the control group and 22 in the experimental group. The breastfeeding education program intervention to promote preterm mothers' self-efficacy used was devised based on the self-efficacy theory. The intervention program consisted of individual breastfeeding education with demonstrations and discharge education, and telephone follow-up education within one week after being discharged. The participants were surveyed before and after the intervention, and four weeks after being discharged from the newborn intensive care unit. Results: The intervention group showed a significant increase in breastfeeding self-efficacy compared with the control group (F=6.92, p=.003) and showed a significant increase in their breastfeeding attitude score (F=3.49, p=.039). Four weeks after discharge, the breastmilk volume of the intervention group increased significantly (t=-2.87, p=.006), and the same group continued to breastfeed more compared with the control group (χ²=4.50, p=.049). Conclusion: This study suggests that the preterm breastfeeding program had a positive effect on breastfeeding self-efficacy, breastfeeding attitude, and extending the breastfeeding period among preterm mothers.

• Resources Recycling
• /
• v.17 no.1
• /
• pp.20-28
• /
• 2008

Leather waste discharged from Shinpyung Changrim Industrial Complex contained 46.3 percent of carbon, and weight loss of leather waste about 50 percent was observed at $500^{\circ}C$ by thermogravimetric analysis. Chemically activated carbon [LW4AC] was made at activation temperature of $800^{\circ}C$ during 30 minutes in electric furnace. Iodine value and decoloration of methylene blue was 968 mg/g and 158 mL/g, respectively. We found that pore volume was more developed according to the increase in the ratio of $K_2CO_3/LW$.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.113-118
• /
• 2014

So many nationwide drinking water treatment plants are under much difficulties by new reinforced discharged effluent standards. Generally, the sludge at thickener should be retended for a long time during usual days. Sometime, the soluble manganese and chloroform may be formed under the anaerobic condition in the sludge thickener when the sludge retention time is longer with low turbidity. This phenomenon results in difficulties to keep regulatory level of the discharged effluent. It was necessary to improve the operation conditions and process itself in order to meet water quality standard recently reinforced. For an effort to overcome the problems, a sludge aeration was successfully implemented into the thickening process. Sludge aeration prevent particle oxidated Manganese eluting soluble de-oxidated Manganese, excrete formated Chloroform from effluent to air, and improve sludge settling through homogenized sludge particle. We aerated sludge at the conventional water treatment plant, measured Manganese and Chloroform of clarified water at upper sludge, and solid-fluid interface height of sludge in mass cylinder. As a result, contaminant's concentrations of the final effluent was much decreased : 41% of manganese, approximately 62% of chloroform and 35% of sludge volume, compared with non-aeration sludge.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.6 no.3
• /
• pp.115-125
• /
• 2001

To examine the movement of the freshwater discharged artificially into the estuary during ebbing period in the Keum River dike we observed surface salinity variations in three stations along the estuary channel in May 1998 and July 1997 and surface temperature and salinity along the ferry-route between Kunsan and Changhang during eighteen days in July 1999. Based upon the typical features of observed salinity variation, we analyzed the excursion and decay processes of the discharged water. When freshwater is discharged, the low-salinity water forms strong salinity front over the entire estuary width, which basically moves forth and back by tidal modulation along the channel, producing the sudden change of surface salinity with the front passage. Salinity distribution along the channel, which is deduced from time variation of mean salinity over the estuary width, after one tidal period from gate operation suggests that diluted low-salinity water is trapped to the front and surface salinity increases gradually toward the upstream region. This frontal distribution of salinity is interpreted to be produced by the sudden gate operation supplying and stopping of freshwater within about two hours. Daily repeat of freshwater discharge produces separation (double front) or merge between decaying and new-generated fronts depending on dike-gate opening time, and the front decays with salinity increasing if the freshwater supply is stopped more than two days. In addition, the observed fluctuations and deviations in surface salinity variation is explained in terms of the differences of fronts intensity, their transition time and temporal salinity front running along the channel, which can be generated due to artificial gate-operation for the discharging time and water volume in the estuary dike.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.229-241
• /
• 2008

In order to investigate stabilization effect on As-contaminated soils treated by zero-valent iron(ZVI) and industrial by-products, batch tests and column tests were carried out with As-contaminated soils collected from farmland around the abandoned mine site. In batch tests, ZVI and industrial by-products(blast furnace slag, steel refining slag and oyster shell powder) were used as treatment materials to reduce As. Industrial by-products were mixed with As-contaminated soils, in the ratio of 1%, 3%, 5% and 7% on the weight base of dried soil. After incubation, all samples showed the reduction of As concentration and it was expected that ZVI and steel refining slag were effective treatment materials to remove As among treatment materials used in batch test. In column tests, columns were made by acrylic with the dimension of diameter=10cm, height=100cm, thickness=1cm and these columns were filled with untreated soils and treated soils mixed with ZVI and steel refining slag(mixing ratio=3%). Distilled water was discharged into the columns with the velocity of 1 pore-volume/day. During test, pH, EC, Eh and As concentration were measured in the regular term(1 pore-volume). As a result, ZVI and steel refining slag were shown 93%, 62% reduction of As concentration respectively by comparison with untreated soils. Therefore, if ZVI and steel refining slag are used as treatment materials in As-contaminated soils, it is expected that the As concentration in soils is reduced effectively.

• Journal of Korean Society on Water Environment
• /
• v.30 no.6
• /
• pp.585-595
• /
• 2014

The temporal trends of the prioritized toxic water pollutants generated and discharged from the industrial facilities in the Geum-River basin, Korea were analyzed with the results of the nationwide Water Pollution Source Survey conducted in 2001 - 2012. The statistical results indicated rapid increase in the volume of raw toxic wastewaters whereas the amount of each toxic pollutant kept fluctuating for 12 years. Serious discrepancies in the survey data of the same type of industries demonstrated a low reliability of the survey result, which stemmed from several error factors. A unit-load for each type of industrial facility was devised to estimate the amount of prioritized toxic water pollutant based on the total volume of industrial wastewater generated from the same type of industrial facilities. The supplementary measures with an effective permit issuance policy and adding survey parameters of terminal wastewater treatment plants to use them as references to the Water Pollution Source Survey were suggested as means to minimize the errors associated with the false reports from the industries.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.65-71
• /
• 2014

As an important component of a fuel cell, the bipolar plate comprises a large proportion in the fuel cell's volume, weight and price. The bipolar plate is the most widely used; however, graphite bipolar plate is large in volume, brittle and therefore easily broken during assembling. In addition, due to its poor machinability, production costs a lot, unless mass production. Compared with the graphite bipolar plate, the metal bipolar plate has good machinability, high electric conductivity and strong mechanical strength; however, it corrodes easily and has a high contact resistance, so in order to prevent corrosion and reduce the contact resistance, the basic metal needs to be processed by use of electro polishing and coating. The water which is produced by electrochemical reactions in the fuel cell must be discharged smoothly. In this study, in order to prevent corrosion the processes of electro polishing and CrN coating were used. According to the presence or absence of these processes, the contact angles can be measured and different metal bipolar plates can be made, these plates can be used for comparing and analyzing the performance of the fuel cell.