• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11A
• /
• pp.921-928
• /
• 2003

This paper propose a new design of directional couplers with the high directivity. The directional coupler is used to check and verify the power, frequency and antenna reflection of a signal at transmission station for the mobile communications. The performance index of the directional coupler is to which the coupling is strong to reduce the effect on the transmitted power and the directivity is high to suppress the interference of the reflected signals and reduce the nor in the communication. Then, the architectures to gain the high directivity and the studies to get the strong coupling have been proposed However, the conventional architectures lot the high directivity and strong coupling have the directivity by about 20㏈ and the difficulty to achieve the higher directivity than 40㏈ suitable for IMT-2000 [1]. This paper proposes an architecture of the directional coupler which is based on the grounding composed of the strip lines and the comparison results with the conventional directional couplers. The comparison results show that the proposed directional coupler has the directivity more than 40 ㏈ and is adequate for the 2.05GHz IMT-2000

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.2
• /
• pp.55-64
• /
• 2003

Underwater acoustic noise measurement is an essential element for vulnerability assessment of modern naval platforms. But during the last few decades environmental conditions have drastically changed due to the gradually increasing sea ambient noise level and decreasing submarine radiated noise level. A real-time underwater acoustic measurement system with vertical line array is designed for the quiet submarine radiated noise assessment in challenging environment. This system has a constant directivity index in measurement frequency range and accurate tracking capability for the transmission loss compensation and navigation aids inside the submarine. This system has been validated at sea and used several times for the submarine noise measurement.

• The Journal of the Acoustical Society of Korea
• /
• v.40 no.4
• /
• pp.391-399
• /
• 2021

The conformal array sensor has different sub-array depending on different beam steering directions. According to the method to effective the sensor, the performance of the conformal array sensor can be different, where the sub-array selects an effective sensor. Also, due to the figure of the conformal array sensor, the figure of the sub-array can be different each other, which results in different performance on directivity index, beam width and etc. In this paper, two methods to select sub-array which is the criteria for each sensors position vector and directive vector were proposed. For two sub-array selection methods, the performance of the directivity index, horizontal and vertical beam width were compared with the average and variance. In addition, this comparison was conducted when the number of sensors was fixed. When the number of sensors was not fixed, the directional vector method mainly results in high performance, but the performance of vertical beam width was lower or equal. When the number of sensors was fixed, the performance of two methods is similar, but the performance of variance was deteriorated.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.8
• /
• pp.61-67
• /
• 1999

This paper proposes a new beamforming algorithm for acoustic measurement by using the nested linear array. In this algorithm, the weighting is optimized by minimizing the LMS error with the initial value obtained by FIR filter design algorithm. The optimization process is applied to each sub-band, which is divided from the octave band, to produce the uniform directivity index. For the optimization pseudo inverse matrix is used for the transfer matrix. As the simulation results, it is found that the proposed algorithm can get the desired beam pattern and unform directivity index so as to be used efficiently for the acoustic measurement by using a nested linear array.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1
• /
• pp.25-31
• /
• 1999

This paper proposes a new wide-band beamforming algorithm which has Gaussian weighting at nested linear array for acoustic measurement. The beamforming is performed one-shot by using all sensors simultaneously, not octave-by-octave. Gaussian weighting of frequency-dependent function is applied to each sensor before time-delay compensation so as to control the frequency receiving band of each sensor. As the results of the simulations, it is confirmed that the proposed algorithm can form the one-shot beams having uniform directivity index and also it can be applied to the broad-band acoustic measurement.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.1267-1270
• /
• 1998

This paper analyzes the characteristics of wide-band one-shot beam formed by using all sensors of array at once, as variation of weighting width. Gaussian function is applied to each sensor as a role of weighting. As the results of the simulation for nested linear array having 17 sensors for each octave, as the width goes wider the directivity index(DI) becomes lower but more even and the variation of beamwidth becomes smaller. It is confirmed, therefore, that weighting width is carefully decided in consideration of DI level, DI stability and the beamwidth.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.639-642
• /
• 1998

This paper proposes a new wide-band beamforming which has guassian weighting. For the prupose of measurement this beam is formed by using all sensors toghether, not octave-by-octave. Weighting is applied to each sensor before time-delay compensation as a frequency-dependent function. As the resutls of the simulation of the proosed algorithm for nested linear array having 17 sensors for each octave, it is confirmed that beam can be formed with all sensors together and uniform directivity index can be achieved by proposed algorithm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.267-271
• /
• 2018

A high directivity TIR (total internal reflection) lens in the UV-A region was designed using a silicone resin, and a UV light source module with a maximum irradiation density of $150mW/cm^2$ was fabricated. The beam angle of the TIR lens was designed to be $8.04^{\circ}$ and the maximum diameter of the TIR lens was Ø13.5. A silicone resin having a UV transmittance of 93% and a refractive index of 1.4 at a wavelength of 365 nm was used, and the lens was manufactured using an aluminum mold, from which silicone could be easily released. The module was fabricated in a metal printed circuit board of COB (chip on board) type using a $0.75{\times}0.75mm^2$ UV chip. A jig was used to adjust the focal length between lens and chip and to fix the position of the lens. The optical characteristics such as illumination distributions of the lens and module were designed using 'LightTools' optical simulation software. The heat dissipation system was designed to use a forced-air cooling method using a heat-sink and fan.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.3
• /
• pp.27-34
• /
• 1999

This paper proposes an algorithm to design the non-linear array so as to form efficiently the one-shot beam with relatively less sensors for acoustic measurement. In this algorithm, according to the spatial sampling theory the part for high frequency(HF) band has equispaced sensor array and the sensor distances below the HF band are decided as a function of number of HF sensors. As the results of the simulations, the mean and variances of directivity index(DI) of non-linear array which has less sensors are similar to those of linear array. and the DI variation for beam steering angle is very small. And the beam width at -2dB point is 6.8°. Thus it is confirmed that the design algorithm for non-linear array which is proposed to have less sensors can be efficiently used in acoustic measurement.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.2
• /
• pp.79-87
• /
• 2011

This paper presents the optimal design of an overlapped ultrasonic sensor ring for high resolution obstacle detection of an autonomous mobile robot. It is assumed that a set of low directivity ultrasonic sensors of the same type are arranged along a circle of nonzero radius at a regular spacing with their beams overlapped. First, taking into account the dead angle region, the entire range of obstacle detection is determined with reference to the center of an overlapped ultrasonic sensor ring. Second, the optimal design index of an overlapped ultrasonic sensor ring is defined as the area closeness of three sensing subzones resulting from beam overlap. Third, the lower and upper bounds on the number of ultrasonic sensors are derived, which can guarantee minimal beam overlap and also avoid excessive beam overlap among adjacent ultrasonic sensors. Fourth, employing a commercial low directivity ultrasonic sensor, an optimal design example of an overlapped ultrasonic sensor ring is given along with the ultrasonic sensor ring prototype mounted on top of a mobile robot. Finally, some experimental results using our prototype ultrasonic sensor ring are given to demonstrate the validity and performance of an optimally overlapped ultrasonic sensor ring for high resolution obstacle detection.