• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.472-477
• /
• 2004

A new earthquake design method performing iterative calculations with secant stiffness was developed. Since basically the proposed design method uses linear analysis, it is convenient and stable in numerical analysis. At the same time, the proposed design method can accurately estimate the inelastic strength and ductility demands of the structural members through iterative calculations. In the present study, the procedure of the proposed design method was established, and a computer program incorporating the proposed method was developed. The proposed method, as an integrated analysis and design method, can directly address the earthquake design strategy intended by the engineer, such as limited ductility of member and the concept of strong column - weak beam. Through iterative calculations on a structural model with member sizes preliminarily assumed, the strength and ductility demands of each member can be determined so as to satisfy the given design strategy. As the result, structural safety and economical design can be achieved.

• 한국건축시공학회지
• /
• 제6권2호
• /
• pp.111-117
• /
• 2006

In case of carrying out vortical crossing water distribution system in expressways or general roads construction, VR(Vibrated and Rolled reinforced concrete) pipes are restricted because of their specification of reinforced spun concrete pipe or on-site made pipe. Therefore, in order to apply VR pipes to those constructions, through the structural behavior experiments of the pipes, VR pipes are compared and verified with reinforced spun concrete pipe and the results are obtained as the following. From the experiments and analyses of Pipe Stiffness(PS) of the pipes, cracking loading is approved to satisfy the KS regulations. Through a direct load test, the cracking loading strength and the maximum load test of VR pipe is larger compared with reinforced spun concrete pipe. Particularly, even if side weld is thin, there is no little change in the cracking strength of VR pipe. The results of the direct load test analysis show that the structural behavior of VR pipe is equivalent or higher compared with reinforced spun concrete pipe in performance and VR pipe could be used as the water distribution pipe for roads. In this study, through pipe stiffness, direct load test and load teat on earth, reinforced spun concrete pipe and VR pipe are compared. And as a result, the structural behavior of VR pipe is comprehensively excellent. From the structural behavior tests, VR pipe's section shows more thickness and has uniform characteristics so that VR pipe is considered more favorable than reinforced spun concrete pipe.

• 한국지반환경공학회 논문집
• /
• 제11권2호
• /
• pp.13-21
• /
• 2010

일반적으로 강우는 사면의 전단강도와 전단응력 변화에 의한 사면붕괴를 유발하므로 강우강도와 전단강도의 변화는 사면안정해석시 매우 중요한 요소이다. 다양한 강우강도가 사면내의 함수비 변화차이를 유발할 뿐만 아니라, 사면 내 지반의 점착력 및 마찰력의 변화를 유발한다. 본 연구의 목적은 강우재현 실험장치를 이용하여, 강우강도와 사면의 전단강도의 관계를 규명하는 것이다. 사용된 토양은 국내의 사면에서 채취한 것으로 입도분석을 실시하였으며, 종래의 함수비 측정방법 대신 TDR 센서를 사용하여 함수비를 측정하였고, 전단강도 측정을 위해 비배수 직접전단시험을 하였다. 본 연구에서의 결과를 정리하면 첫째, 함수비는 토양의 투수성과 밀접한 관계를 가지며, 강우지속기간은 토양함수비를 결정하는데 중요한 요소이다. 둘째, 강우재현 실험장치를 이용한 안정성 분석은 사면에서의 함수비와 전단응력의 측정이 가능하여, 매우 유용한 사면해석방법이다. 셋째, 함수비와 관련된 비배수 전단응력식을 제시하였으며, 제시한 식은 기존 연구와 비교하여 보다 간편한 것으로 나타났다.

• Restorative Dentistry and Endodontics
• /
• 제47권2호
• /
• pp.15.1-15.18
• /
• 2022

This review aimed to characterize the effect of direct restorative material types and adhesive protocols on marginal adaptation and the bond strength of the interface between the material and the proximal dentin/cementum. An electronic search of 3 databases (the National Library of Medicine [MEDLINE/PubMed], Scopus, and ScienceDirect) was conducted. Studies were included if they evaluated marginal adaptation or bond strength tests for proximal restorations under the cementoenamel junction. Only 16 studies met the inclusion criteria and were included in this review. These studies presented a high degree of heterogeneity in terms of the materials used and the methodologies and evaluation criteria of each test; therefore, only a descriptive analysis could be conducted. The included studies were individually evaluated for the risk of bias following predetermined criteria. To summarize the results of the included studies, the type of restorative material affected the test results, whereas the use of different adhesive protocols had an insignificant effect on the results. It could be concluded that various categories of resin-based composites could be a suitable choice for clinicians to elevate proximal dentin/cementum margins, rather than the open sandwich technique with resin-modified glass ionomers. Despite challenges in bonding to proximal dentin/cementum margins, different adhesive protocols provided comparable outcomes.

• 아동학회지
• /
• 제37권2호
• /
• pp.13-25
• /
• 2016

Objective: The purposes of this study were to examine the effects of school-age children's ego strength, failure tolerance, and performance anxiety on their school class adjustment, and to model the relation structure of the variables. Method: For these purposes, a questionnaire survey was conducted with 562 6th graders. Results and Conclusion: The results of this study are summarized as follows. First, ego strength, failure tolerance, and performance anxiety were significantly different according to gender. Second, in male students, ego strength, failure tolerance, and performance anxiety had a significant direct effect on school class adjustment. In addition, ego strength and failure tolerance had a significant indirect effect on school class adjustment. Third, female students' paths to school class adjustment were similar to male students' but the effect of failure tolerance on performance anxiety and the effect of performance anxiety on school class adjustment were not significant. Fourth, in the results of multi-group analysis, the effect path from ego strength to school class adjustment was different between male and female students, and the effect was higher in female students than in male students.

• 한국환경보건학회지
• /
• 제31권4호
• /
• pp.260-265
• /
• 2005

Indoor air quality might be affected by source strength of indoor pollutants, ventilation rate, decay rate, outdoor level, and so on. Although technologies measuring these factors exist directly, direct measurements of all factors are not always practical in most field studies. The purpose of this study was to develop an alternative method to estimate the source strength and deposition constant by application of multiple measurements. For the total duration of 60 days, indoor and outdoor $NO_2$ concentrations every 3 days were measured in 30 houses in Seoul, Asan and Daegu. Using a compartment model by mass balance and linear regression analysis, penetration factor (ventilation divided by sum of air exchange rate and deposition constant) and source strength factor (emission rate divided by sum of air exchange rate and deposition constant) were calculated. Subsequently, the source strength and deposition constant were estimated. Natural ventilation was $1.80{\pm}0.42\;ACH,\;1.11{\pm}0.50\;ACH,\;0.92{\pm}0.26\;ACH$ in Seoul, Asan and Daegu, respectively. Calculated deposition constant(K) and source strength of $NO_2,$ in this study were $0.98{\pm}0.28\;hr^{1}\;and\;16.28{\pm}7.47\;ppb/h,$ respectively.

• Journal of the Korean Wood Science and Technology
• /
• 제30권3호
• /
• pp.59-65
• /
• 2002

EYM (European Yield Model), which was adopted in NDS (National Design Specification for wood construction), has been used in Korea without any verification of the analysis of bolted wood connections. In the case of applying lumber from domestic small diameter logs, however, there are some problems with the direct application of EYM ; 1) relatively low dowel bearing strength and dimensional stability due to a large amount of immature wood, 2) effect of MC (moisture contents) on the dowel bearing strength of wood and the yield load of a bolted connection. To evaluate the strength properties of bolted connections with lumber from domestic small diameter logs, effect of MC on the dowel bearing strength of wood was investigated and double shear bolted connection tests were performed. As the MC of wood increased, the dowel bearing strength was linearly reduced, even under 19% MC, which showed that adjustment, not considered in NDS, was required. Double shear bolted connection tests indicated that effect of MC on yield load should be considered in order to determine design value.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권3호
• /
• pp.147-154
• /
• 2008

풍화토 사면은 장시간 공기에 노출되거나 물과 접촉을 하게 되면 전단강도가 급격히 저하되며 계절에 따른 수위의 변화가 매우 큰 댐사면의 경우는 강도저하가 더욱 크게 발생한다. 풍화토 사면의 강도저하 파악을 위하여 반복전단시험 및 수침 건조를 반복한 시료에 대한 잔류강도 시험을 통해 포화에 따른 강도의 저하를 파악하였다. 또한 소형동적콘관입시험기를 이용하여 관입타격횟수와 전단강도정수관계를 파악하고 인공신경망 해석을 통하여 관입타격횟수 Nc를 이용한 전단강도정수의 예측이 용이하도록 상관식을 구성하였다.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.281-290
• /
• 2022

The direct shear test is commonly used to evaluate the shear behavior of frozen soil-structure interfaces under normal stress. However, failure criteria, such as the Mohr-Coulomb failure criterion, are needed to obtain the unconfined shear strength. Hence, the punch shear test, which is usually used to estimate the shear strength of rocks without confinement, was examined in this study to directly determine the adfreezing strength. It is measured as the shear strength of the frozen soil-structure interface under unconfined conditions. Different soils of silica sand, field sand, and field clay were prepared inside the steel and concrete ring structures. Soil and ring structures were frozen at the target temperature for more than 24 h. A punch shear test was then conducted. The test results show that the adfreezing strength increased with a decrease in the target temperature and increase in the initial water content, owing to the increase in ice content. The adfreezing strength of field clay was the smallest when compared with the other soil specimens because of the large amount of unfrozen water content. The field sand with the larger normalized roughness showed greater adfreezing strength than the silica sand with a lower normalized roughness. From the experiment and analysis, the applicability of the punch shear test was examined to measure the adfreezing strength of the frozen soil-structure interface. To find a proper sample dimension, supplementary experiments or numerical analysis will be needed in further research.

• Geomechanics and Engineering
• /
• 제12권4호
• /
• pp.639-655
• /
• 2017

The binary mixture consists of two types of granular media with different physical attributes and sizes, which can be characterized by the percentage of large granules by weight (P) and the particle size ratio (${\alpha}$). Researchers determine that two thresholds ($P_S$ and $P_L$) exist for the peak shear strength of binary mixtures, i.e., at $P{\leq}P_S$, the peak shear strength is controlled by the small granules; at $P{\leq}P_L$, the peak shear strength is controlled by the large granules; at $P_S{\leq}P{\leq}P_L$, the peak shear strength is governed by both the large and small granules. However, the thresholds of binary mixtures with different ${\alpha}$ values, and the explanation related to the inner details of binary mixtures to account for why these thresholds exist, require further confirmation. This paper considers the mechanical behavior of binary mixtures with DEM analysis. The thresholds of binary mixtures are found to be strongly related to their coordination numbers $Z_L$ for all values of ${\alpha}$, where $Z_L$ denotes the partial coordination number only between the large particles. The arrangement structure of the large particles is examined when P approaches the thresholds, and a similar arrangement structure of large particles is formed in both 2D and 3D particle systems.