• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.434-439
• /
• 2002

The researches on the direct drive system, which directly transfers axle load of the traction motor to wheels, have been developed as a next generation drive system in Japan and Europe. As a result of excluding couplings and gear units, the direct drive system has advantages on the bogie mount space to be smaller sized, lower noisy, more efficient and less weighted than the conventional drive system - indirect drive system. Since the simplification of the direct drive system design depends on the design of the traction motors, the researches on the direct drive system with focusing on the traction motors get started. The advantages/disadvantages of direct drive system, types, structures, cooling systems and interfaces of the traction motors are presented on this paper. Furthermore, the development of other countries on the electric equipments of the next generation railway vehicles are discussed and the necessity ＆ requirement for developing new concepts of traction motors are assured.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.25-31
• /
• 1995

In this paper, a direct drive scalar robot manipulator is constructed and its mechanical machanism for operation is explained. Also, a motion controller board for the direct drive robot manipulator was developed where the IBM 486 computer is the main controller. For the developed direct drive robot, a force/motion control algorithm based on an active compliance scheme is developed. A preliminary experiment using the developed direct drive for a peg-in-hole job was done by implementing the control algorithm.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.34-46
• /
• 1987

The drive efficiency is investigated with drawbar pull test to provide the basic data in the gradability and acceleration of the wheeled vehicle. As a result, the drive efficiencies are determined from 4*2 drive : Direct gear 0.89 1st gear 0.81 Other gears 0.83-0.87 4*4 high drive : Direct gear 0.85 1st gear 0.77 Other gears 0.79-0.83 4*4 low drive : Direct gear 0.83 1st gear 0.75 Other gears 0.77-0.81

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.239-243
• /
• 1989

This paper represents the control software development for Direct Drive Arm Robot with the WHILE language composed the 68000 assembly language and high level language modula-2. Direct Drive Ann Robot needs the control program which is fast step and exactly position moving because Direct Drive Arm Robt depends on accuracy. We found that the self-tuning algorithm for this robot control is very good for the real time control and the floating point operation using the 32 bit CPU(MC 68020) controller.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1819-1826
• /
• 1997

Direct-drive robots are suitable to the position and force control with high accuracy, but it is difficult to design a controller because of the system's nonlinearity and link-interactions. This paper is concerned with the study of the force control of direct-drive robots. The proposed algorithm consists of feedback controllers and a neural network. After the completion of learning, the output of feedback controller is nearly equal to zero, and the neural network controller plays an important role in the control system. Therefore, the optimum retuning of parameters of feedback controllers is unnecessary. In other words, the proposed algorithm does not require any knowledge of the controlled system in advance. The effectiveness of the proposed algorithm is demonstrated by the experiment on the force control of the parallelogram link-type direct-drive robot.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.582-592
• /
• 2009

This paper proposes a new speed sensorless direct torque and flux controlled interior permanent magnet synchronous motor (IPMSM) drive. Closed-loop control of both the torque and stator flux linkage are achieved by using two proportional-integral (PI) controllers. The reference voltage vectors are generated by a SVM unit. The drive uses an adaptive sliding mode observer for joint stator flux and rotor speed estimation. Global asymptotic stability of the observer is achieved via Lyapunov analysis. At low speeds, the observer is combined with the high frequency signal injection technique for stable operation down to standstill. Hence, the sensorless drive is capable of exhibiting high dynamic and steady-state performances over a wide speed range. The operating range of the direct torque and flux controlled (DTFC) drive is extended into the high speed region by incorporating field weakening. Experimental results confirm the effectiveness of the proposed method.

• Journal of the Korean Society of Safety
• /
• v.17 no.4
• /
• pp.87-93
• /
• 2002

This paper is presented new fuzzy controller for high performance of induction motor drive. New fuzzy controller took out appropriate amounts of accumulated control input according to fuzzy described situations in addition to the incremental control input calculated by conventional direct fuzzy controller. The structures of the proposed controller was motivated by the problems of direct fuzzy controller. The direct controller was given generally inevitable overshoot when one tries to reduce rise time of response. The undesirable characteristics of the direct fuzzy controller are caused by integrating operation of the controller, even though the integrator itself is introduced to overcome steady state error in provide a thorough comparative insight into the behavior of induction motor drive with direct and new fuzzy speed controller. The validity of the comparative results is confirmed by the simulation results for induction motor drive system.

• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.1222-1224
• /
• 1996

The Hong Ik Direct Drive Arm(HIDDA) is a SCARA typed direct drive manipulator with two degrees-of-freedom(DOF) using the direct drive motor of the NSK company. The direct NSK motors are used to give a large torque directly to the link, to reduce the modeling errors from the gears and chains. But, since the nonlinear coupling torques are transferred to the motor shaft without any reduction, we must consider a dynamic control algorithm. In this paper, we designed a robot controller for the HIDDA using a TMS320C31, which has the highest performance among the third DSP chips in the TI company. And we developed the integrated environment software of the robot management system to give the users an easy way of programming, running and simulation of the robot on the PC.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.194-199
• /
• 1989

In this paper, using the direct drive arm for plant, the controller is developed to track the desired trajectory in high speed and precision. For the purpose of this, through extending self-tuning pole-placement algorithm, we developed self-tuning pole-shift algorithm which is fast in response and good tracking for the reference tracking change. Developed controller is applied a three-link direct drive arm with the varing payload to track the desired tracking. And, through the computer simulation, the performance of developed controller is compared with the performance of the computed torque method and the self-tuning pole placement algorith.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.82-85
• /
• 1988

This paper are the manufacture of controller of direct drive arm robot using 32 bit CPU(MC 69020). The work would draw on KIT of Robotics Laboratory whose extensive experience in 16 bit CPU Controller(MC 68008) in addition to the WHILE languages. We found that this controller is good for the direct drive arm robot controller for the use of self-tuning algorithms and real time control.