• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.25-37
• /
• 1995

The phenomenological loss equivalence method incorporated into the wideband lossy transmission line model is applied to the characterization of high desity digital transmission lines. The pulse propagation characteristics are analyzed using the calculated frequency characteristics and the discrete Fourier transformation. This approach has been verified by comparing the calculated frequency characteristics with the FEM and the esperimental results. This method is very suitable for computer-aided analysis of high density/high speed interconnection circuits because of the simple calculation as well as the calculation accuracy. We have found that pulse ftransmission speed and dispersion of hgih density digital transmission lines can be optimized by managing the conductor and dielectric losses in addition to the impedance matching.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.36S no.11
• /
• pp.1-8
• /
• 1999

In this paper, new polyphase sequences and a sequence generation method are suggested. These sequences are found to have good correlation properties. Since the suggested generation method consists only of integer sums and modular techniques, sequence generation is also easy. The performance of the sequences is investigated when used in QS-CDMA systems under frequency selective, time nonselective, slow Nakagami fading channel with additive white Gaussian noise.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.4
• /
• pp.379-385
• /
• 2018

The transmission of analog signals through Galvanic isolators often results in signal distortion. Optocoupler gain is temperature dependent and also varies considerably, which would cause deformations of analog signals. Digital isolators have better noise immunity than analog, and digital transmission is a cost-effective noise rejection method for multichannel analog signals, which can solve temperature-induced signal distortion problems. Digital data, converted from multichannel analog signals, can be transmitted through a single optocoupler. We proposed advanced circuits and data frame for robust transmission of multichannel analog signals. Numerical experiments were performed to investigate distortion of multichannel analog signals during transmission.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.2
• /
• pp.63-70
• /
• 2019

Electric transmission towers are facilities to transport electrical power from a plant to an electrical substation. The towers are connected using wires considering the wire tension and the clearance from the ground or nearby objects. The wires are installed on a rights-of-way that is a strip of land used by electrical utilities to maintain the transmission line facilities. Trees and plants around transmission lines must be managed to keep the operation of these lines safe and reliable. This study proposed the use of a low-cost drone photogrammetry for the transmission line rights-of-way mapping. Aerial photogrammetry is carried out to generate a dense point cloud around the transmission lines from which a DSM (Digital Surface Model) and DTM (Digital Terrain Model) are created. The lines and nearby objects are separated using nDSM (normalized Digital Surface Model) and the noises are suppressed in the multiple image space for the geospatial analysis. The experimental result with drone images over two spans of transmission lines on a mountain area showed that the proposed method successfully generate the rights-of-way map with hazard nearby objects.

• Journal of Digital Convergence
• /
• v.10 no.9
• /
• pp.369-374
• /
• 2012

In this paper, the effective transmission method is proposed to save the energy and to increase the throughput of the communication system using adaptive modulation. Traditionally, adaptive modulation has been used to improve the throughput using the power margin of the system design. Considering the instantaneous energy during the modulation method changing duration, the effective transmission method is proposed. By the simulation, the performance and effectiveness is validated.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.653-658
• /
• 2003

This study is represented a method to give connect to optical cable from accident site and reviewed the method to transmission a moving image to control centre by real time, following the study of image transmission method in copper cable section where is a main line of railroad communication. Concept of network is studied to use cable and equipment effectively, and it's also reviewed technology of digital image transmission system and image evaluation methods, in spite of the pixel of camera and monitor resolution determine quality of image when moving image transferring by point to point. In addition, this study is reviewed checks and considerations of image transmission equipment (codec) with various transmission methods in room test, and then examined and analyzed wire/wireless combined transmission methods at wayside.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1355-1359
• /
• 2004

The two way subscriber transmission systems have tendency to spread its carrier frequency bandwidth or information bit rate and average bit error rate according to popularization of high speed information through the digital communication system, transmission medium and the Internet. This fact is an important incentive to realize new systems. These two way subscriber transmission systems usually use same cable or same carrier frequency bandwidth for up stream channel and down stream channel. In the systems, the disturbances of noise, crosstalk or fading affect the characteristics. Specifically, these disturbances cause the decrease of information bit rate and degradation of transmission quality. This paper proposes the improved method of their degradations using the particular feature of two way subscriber transmission systems and it makes clear proposed method is effective by theoretically and some numerical examples.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05a
• /
• pp.471-476
• /
• 1996

In this study, the method to use the phase shift keying (PSK) communication technique in smart transmitter is presented. In nuclear applications. smart transmitters for various parameters are expected to improve the accuracy of measurement and to reduce the load of calibration work. The capability of communication in field level is the most important merit of the smart transmitter. The most popular method is using of digital and analog techniques simultaneously - transmitting measurements from the field at 4∼20mA while modulating the current to carry digital information in both directions over the same twisted pairs. Conventional smart transmitters use the frequency shift keying (FSK) method for digital communication. Generally, however, the FSK method has the speed limit at 1200 bps. Amount of information to transmit becomes increasing as the processing technique is improved. The PSK method is noticeable alternative for high speed digital communication, but it has non-zero DC component. In order to use the PSK method in the field transmission with smart transmitter, the method to remove the DC component is studied in this work.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.79.6-79
• /
• 2002

We propose here sequential 2 methods for obtain information of current or potential data for power transmission line. One is a digital data transmission unit, this is, an output of a current sensor of power transmission line is digitalized by use of an easy asynchronous protocol. The unit has high speed transform rate, easy making header caused of consisting of only logic circuit. The other is, the output of the unit is transformed via LAN interface and displayed on a personal computer. We have confirmed remote measuring using the method for 100A and 240 A of the current information of power transmission line. Therefore we will be able to see a current waveform by use of internet at a cheep c...

• Journal of Digital Convergence
• /
• v.11 no.12
• /
• pp.401-406
• /
• 2013

In this paper, the optimum transmission method is proposed to save the energy and to increase the throughput of the adaptive modulation mobile radio system with frame length control. Traditionally, adaptive modulation has been used to improve the throughput using the power margin of the system design. Considering the frame length vs energy saving and adaptive modulation, the optimum transmission method is proposed for hub and mobile station each.