• Journal of Korea Multimedia Society
• /
• v.15 no.3
• /
• pp.364-371
• /
• 2012

Currently, CMMB(China Mobile Multimedia Broadcasting) and the conventional analog TV broadcasting have transmitted by using UHF(Ultra High Frequency : 474MHz~754MHz) band. Normally, the transmission power of the digital TV broadcasting is lower than the conventional analog TV broadcasting to protect the reception quality of the conventional analog TV broadcasting. The reception sensitivity of CMMB receiver has severely deteriorated due to adjacent the conventional analog TV broadcasting signals which called ACI (Adjacent Channel Interference). To improve the reception sensitivity of a CMMB receiver on ACI environment, this paper proposed a simple method which is tuning a cut off frequency of LPF (Low Pass Filter). From the experiment, the reception sensitivity of CMMB receiver was improved as 11.3dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.979-986
• /
• 2013

In this paper, a TVS diode which is commonly used as a ESD protector in wireless communication devices could cause antenna wireless sensitivity to decrease has been analyzed. When a smartphone doesn't have enough space to place many components, there would be its speaker near antenna area. In order to protect ESD coming through the speaker there also could be a TVS within antenna GND area. Digital audio signal which was sent to speaker and CDMA RF communication signal coupled from antenna was mixed by TVS. And this leakage current running through TVS resulted in decrease of antenna wireless sensitivity. The results of various experiments can be explained using circuit simulation. Following works will give us some insights that can reduce unwanted summation of digital and RF signal due to nonlinearity of ESD protectors.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.38-46
• /
• 2011

In this paper, we propose a calculation methodology of the service distance to assure the satisfactory quality of service for analogue and digital TV receivers. Using the field strength formulation for TV receiver based upon Rec. ITU-R P.1546, computational results are presented and discussed for both systems, and some important factors are reviewed in terms of the equivalent level of service, which must be kept due to ATV to DTV conversion. The presented method provides the predicted values of field strength at receiver areas to check whether transmission quality can be satisfied or not, and it can be also used for obtaining the protection ratio or separated distance from co-channel or adjacent interference signal.

• Journal of Broadcast Engineering
• /
• v.16 no.5
• /
• pp.824-833
• /
• 2011

In this paper, using the Rec. ITU-R P.1546 explaining a propagation prediction model in the VHF and UHF bands, we propose the analytical methodology for calculating the service distance and field strength for analogue and digital TV receivers. From the derived formulation of the receiver field strength, some computation results are presented and discussed in terms of the equivalent level of service caused by analogue to digital TV conversion. The suggested method is also applicable to the analysis of frequency coordination or compatibility from unwanted signal in VHF and UHF bands.

• Journal of Broadcast Engineering
• /
• v.15 no.6
• /
• pp.731-741
• /
• 2010

In this paper, we propose the methodology of prediction of field strength for a digital television (DTV) receiver by virtue of Recommendation ITU-R P.1546. The curves shown in this recommendation represent the point-to area field strength for 1.0 kW effective radiated power in the 30 MHz ~ 3000 MHz. Based upon the procedures described in this Recommendation, computation results are presented here from the derived formulation of field strength for DTV receiver. To show the validity of this method, some results are compared with the analysis by Okumura-Hata model and it was shown that the error of field strength is in the range of 6.9 ~ 11.5 %. The presented method provides not only the predicted values of field strength for DTV receiving area to check the quality of transmitted signal, but also an appropriate site selection for obtaining good propagation environment. In addition, it can be directly used for analyzing the protection ratio or separated distance for frequency sharing in the same band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.3 s.333
• /
• pp.25-34
• /
• 2005

In this paper, we analyzed and measured the electrical crosstalk characteristics of a triplex transceiver module for ethernet Passive optical networks(EPONS). And we improved the electrical crosstalk levels using Dummy ground lines with signal lines. The triplex transceiver module consists of a laser diode as a transmitter, a digital photodetector as a digital data receiver, and a analog photodetector as a community antenna television signal receiver. And there are integrated on silicon substrate. The digital receiver and analog receiver sensitivity have to meet -24 dBm at $BER=10^{-l2}$ and -7.7 dBm at 44 dB SNR. And the electrical crosstalk levels have to maintain less than -86 dB from DC to 3 GHz. From analysis and measurement results, the proposed silicon substrate structure that contains the Dummy ground line with $100\;{\mu}m$ space from signal lines and separates 4 mm among devices respectively, is satisfied the electrical crosstalk level compared to simple structure. This proposed structure can be easily implemented with design convenience and greatly reduced the silicon substrate size about $50\%$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.4
• /
• pp.381-388
• /
• 2015

In this paper, a wireless video streaming system is designed and implemented for TV white space applications. It consists of a RF transceiver module, a digital modem, a camera, and a LCD screen. A VGA resolution video is captured by a camera, modulated by modem, and transmitted by RF transceiver module, and finally displayed at a destination 2.6-inch LCD screen. The RF transceiver is based on direct-conversion architecture. Image leakage is improved by low pass filtering LO, which successfully covers the TVWS. Also, DC offset problem is solved by current steering techniques which control common mode level at DAC output node. The output power of the transmitter and the minimum sensitivity of the receiver is +10 dBm and -82 dBm, respectively. The channel bandwidth is tunable among 6, 7 and 8 MHz according to regulations and standards. Digital modem is realized in Kintex-7 FPGA. Data rate is 9 Mbps based on QPSK and 512ch OFDM. A VGA video is successfully streamed through the air by using the developed TV white-space RF communication module.