• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2002년도 추계종합학술대회
• /
• pp.425-429
• /
• 2002

In this paper, a single-phase inverter using a diode bridge-type resonant circuit to implement ZVT(Zero Voltage Transition) switching is presented. The current control algorithm is analyzed about how to design the circuit with auxiliary switch which can ZVT operation for the main power switch. The simulation and experimental results would be shown to verify the proposed current algorithm, because the main power switch is turn on with ZVT and the hi-directional inverter is operated.

• 전기학회논문지P
• /
• 제53권3호
• /
• pp.142-147
• /
• 2004

In this study, We developed the microprocessor based controller for Auto Section Switch(ASS). This is installed at consumer's medium-high voltage(load capacity is below 4,000 kVA) switchgear. This function is cooperate with protection device of fault section and automatically dividing the section. And It is designed by Air putter type extinction structure and adopt the mechanism and breaking part module of existing Load Breaker Switch. In addition, We successfully conducted the operation test and checked main function of proto-type.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.106-108
• /
• 2005

High accuracy and stability digital controlled power supply for magnet is developed at PLS. This power supply has three sections. The first section is digital controller including DSP&FPGA and precision ADC, the second section consists of IGBT driver and four quad IGBT switch, and the third section is LC output filter section. AC input voltage of power supply is 3-phase 21V, output current is 0 ${\sim}$ 150 A dc. Switching frequency of four quad IGBT switch is 25 kHz. The output current of power supply has very high accuracy of 100 A step resolution at full range and the stability of +/- 1.5 ppm for short term and +/- 5 ppm for long term. This paper describes characteristics of filter and output current performance improvement after LC output filter at four quad digital power supplies.

• 한국멀티미디어학회논문지
• /
• 제25권8호
• /
• pp.1007-1021
• /
• 2022

Autonomous driving of unmanned aerial vehicles may have to pay expensive cost to create and switch new routes if unexpected obstacles exist or local map updates occured by the control system due to incorrect route information. Integrating digital twins into the path-following process requires more computing resources to quickly switch the wrong path to an alternative path, but it can quickly update the path during flight. In this study, we design a DEVS-based simulation environment which can modify optimized paths through short-term simulation of multi-virtual UAVs for applying digital twin concepts to path follow. Through simulation, we confirmed the possibility of increasing the mission stability of UAV.

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.36-40
• /
• 2005

The problem of fluctuation-induced digital errors in a rapid single flux quantum (RSFQ) circuit has been a very important issue. In this work, we calculated the bit error rate of an RSFQ switch used in superconductive arithmetic logic unit (ALU). RSFQ switch should have a very low error rate in the optimal bias. Theoretical estimates of the RSFQ error rate are on the order of $10^{-50}$ per bit operation. In this experiment, we prepared two identical circuits placed in parallel. Each circuit was composed of 10 Josephson transmission lines (JTLs) connected in series with an RSFQ switch placed in the middle of the 10 JTLs. We used a splitter to feed the same input signal to both circuits. The outputs of the two circuits were compared with an RSFQ exclusive OR (XOR) to measure the bit error rate of the RSFQ switch. By using a computerized bit-error-rate test setup, we measured the bit error rate of $2.18{\times}10^{-12}$ when the bias to the RSFQ switch was 0.398 mA that was quite off from the optimum bias of 0.6 mA.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.760-767
• /
• 2014

This paper describes a high-radix crossbar switch design with low latency and power dissipation for Network-on-Chip (NoC) applications. The reduction in latency and power is achieved by employing a folded-clos topology, implementing the switch organized as three stages of low-radix switches connected in cascade. In addition, to facilitate the uniform placement of wires among the sub-switch stages, this paper proposes a Mux-Matrix-Mux structure, which implements the first and third switch stages as multiplexer-based crossbars and the second stage as a matrix-type crossbar. The proposed 256-radix, 8-bit crossbar switch designed in a 65nm CMOS has the simulated power dissipation of 1.92-W and worst-case propagation delay of 0.991-ns while operating at 1.2-V supply and 500-MHz frequency. Compared with the state-of-the-art designs in literature, the proposed crossbar switch achieves the best energy-delay-area efficiency of $0.73-fJ/cycle{\cdot}ns{\cdot}{\lambda}^2$.

• 한국정보통신학회논문지
• /
• 제14권8호
• /
• pp.1849-1854
• /
• 2010

디지털 병원이 지향하고 있는 병원내의 정보화 시스템으로는 영상저장 및 전송시스템을 비롯한 여러 시스템들이 있다. 영상저장 및 전송시스템은 병원 내에서 발생하는 각종 의료영상을 저장하고 전송하는 시스템이며, 시술 중 필요한 각종 의료영상은 키보드나 풋 스위치를 이용하여 캡쳐한다.본 연구에서는 메인 풋 스위치 케이스 내에 탐재 가능한 풋 스위치용 USB 모듈을 MicroController가 내장된 USB지원 MCU 관련 회로와 최대 5개 풋 스위치를 위한 I/O 인터페이스 부분 등으로 설계 구현하고, 다양한 기능을 제공하는 풋 스위치 제어 프로그램을 개발하였다. 개발한 풋 스위치 USB 모듈을 병원 현장에 적용한 결과 안정적으로 동작함을 확인할 수 있었다.

• 한국통신학회:학술대회논문집
• /
• 한국통신학회 2006년도 하계종합학술발표회 논문 초록집
• /
• pp.373-373
• /
• 2006

• ETRI Journal
• /
• 제33권2호
• /
• pp.275-278
• /
• 2011

This letter presents a polymer $1{\times}2$ thermo-optic totalinternal-reflection digital optical switch (TIR-DOS) with an index contrast of 1.5%-${\delta}$ operating at low power consumption. The structure of our $1{\times}2$ TIR-DOS was created by adding a reflection port to that of a conventional multimode filtering variable optical attenuator. To improve the total-internalr-eflection efficiency, a heater offset was applied to the crossing region of multimode waveguides of the TIR-DOS. The fabricated $1{\times}2$ TIR-DOS shows a low electrical power consumption of 18 mW for an on-off ratio of 35 dB.

• 한국통신학회논문지
• /
• 제22권6호
• /
• pp.1148-1159
• /
• 1997

In the broadband integrated service digital networks (B-ISDN), ATM switches hould be abld to accommodate diverse types of applications ith different traffic characteristics and quality ddo services (QOS). Thus, in order to increase the utilization of switches and satisfy the QOS's of each traffic type, some types of priority control schemes are needed in ATM switches. In this paper, a nonblocking input and output queueing ATm switch with capacity C is considered in which two classes of traffics with different loss probability constraints are admitted. 'Partial push-out' algorithm is suggested as a loss priority control schemes, and the performance of this algorithm is analyzed when this is adopted in input buffers of the switch. The quque length distribution of input buffers and loss probabilities of each traffic are obtained using a matrix-geometric solution method. Numerical analysis and simulation indicate that the utilization of the switch with partial push-out algorithm satisfying the QOS's of each traffic is much higher than that of the switch without control. Also, the required buffer size is reduced while satisfying the same QOS's.