• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.570-575
• /
• 2006

In this paper, we have investigated thermal properties by changing the content of carbon nanotube, which is component part of semiconductive shield in underground power transmission cable. Heat capacity (${\Delta}H$), glass transition temperature (Tg) and melting temperature (Tm) were measured with the samples of eight, through DSC (Differential Scanning Calorimetry), and the measurement ranges of temperature selected from $-100[^{\circ}C]\;to\;100[^{\circ}C]$ with heating temperature selected per $4[^{\circ}C/min]$ Also, high temperature, heat degradation initiation temperature, and heat weight loss were measured by TGA (Thermogravimetric Analysis) in the temperature from $0[^{\circ}C]\;to\;700[^{\circ}C]$ with rising temperature of $10[^{\circ}C/min]$. As a result, the Glass transition temperatures of the sample were showed near $-20[^{\circ}C]{\sim}25[^{\circ}C]$, and the heat capacity and melting temperature from the DSC was increased according to increasing the content of carbon nanotube, while, thermal diffusivity was increased according to increasing the content of carbon nanotube. Also, heat degradation initiation temperature from the TGA results was increasing according to increasing the content of carbon nanotube with CNT/EEA. Therefore, heat stabilities of EVA, which contained the we VA (vinyl acetate), showed the lowest.

• Journal of Pharmaceutical Investigation
• /
• v.27 no.3
• /
• pp.233-239
• /
• 1997

Glibenclamide is a second generation sulfonylurea that is orally active as a hypoglycemic drug. It exists as a crystalline powder which is sparingly soluble in water. It was investigated that the potential of glibenclamide to exhibit polymorphism. Three polymorphic modifications (form 1, form 2 and form 3) and three pseudopolymorphic modifications (form 4, form 5 and form 6) were obtained by crystallization from different organic solvents. The isolated crystal forms were characterized by differential scanning calorimetry(DSC), thermogravimetric analysis(TGA) and X-ray crystallography powder diffraction studies. Form 1 was the most stable and melt at $175.4^{\circ}C$. Form 2 was metastable and melt at $151.0^{\circ}C$. Form 3 was a new polymorphic modification because it was different from form 1 and form 2 in X-ray crystallography powder diffraction data. Form 4 was a 1 : 7(toluene : glibenclamide) toluene solvate; form 5 was a 1 : 5(toluene : glibenclamide) toluene solvate; form 6 was a 3 : 8(pentanol : glibenclamide) pentanol solvate. All forms were stable in 3-month storage under 0% or 100% humidity condition. The dissolution rate of form 4 was highest; those of form 2, form 3, form 1, form 5 and form 6 followed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.4
• /
• pp.1988-1992
• /
• 2011

Polypropylene (PP)-SEBS/silicate composites with PP content of 35, 40, and 45wt% were fabricated by melt compounding at $200^{\circ}C$, using lab scale Brabender mixer. The content of silicate was fixed at 5wt%. The thermal properties of the PP-SEBS/silicate composites were investigated by differential scanning calorimetry (DSC) and thermogravimetric analyzer (TGA). The melting temperature of PP-SEBS compound decreased up to $141^{\circ}C$ with SEBS content. TGA result indicates an increase in degradation temperature when the silicate was added in the PP-SEBS compound. The rheological properties of the compounds were measured by dynamic Rheometer. PP-SEBS/silicate composite indicates higher shear thinning and elastic property than PP-SEBS compound. Van Gurp-Palmen analysis was applied in order to certify an increase in elasticity.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.1
• /
• pp.19-22
• /
• 2012

Transformation behavior of rapidly solidified Ti-47.3Ni (at%) alloy ribbons and thermal stability of the R phase in the ribbons were investigated by means of differential scanning calorimetry (DSC), X-ray diffraction, and transmission electron microscopy. Rapidly solidified Ti-47.3Ni alloy ribbons showed the two-stage B2-R-B19' martensitic transformation behavior. The B2-R transformation in the ribbons was observed even after annealing at 1,223 K, which was attributed to the fact that a specific orientation relationship between $Ti_2Ni$ and matrix in the ribbons is maintained after annealing at 1,223 K. The DSC peak temperature of the B2-R transformation ($T_R^*$) decreased with raising annealing temperature, which was attributed to the increased volume fraction of $Ti_2Ni$, thus causing an increased Ni content in the matrix.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.399-406
• /
• 2000

A thermotropic liquid crystalline polymer (TLCP) containing a flexible spacer was synthesized from hydroquinone, p-hydrofybenzoic acid, and 1,6-dibromohexane. Intercalation of TLCP in layered clays is accomplished by heating the polymer with dodecyl ammonium-montmorillonite (C$_{12}$-MMT) above melt transition temperature (T$_{m}$). Liquid crystallinity of the TLCP/C$_{12}$-MMT hybrid was not observed when $C_{12}$-MMT content was above 1 wt%. Some of the $C_{12}$-MMTs in TLCP were highly dispersed in a nanometer scale, but some of them were agglomerated. Thermal and morphological properties of the nanocomposites were examined by differential scanning calorimetry (DSC), thermogravimetric analyzer (TGA), polarized optical microscope, and electron microscopes (SEM and TEM). TEM).

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.2
• /
• pp.38-46
• /
• 1991

Effects of aging treatment on the microstructures and microhardness of a rapidly solidified Al-Li-Cu-Mg-Zr alloy were investigated by differential scanning calorimetry(DSC) and transmission electron microscopy(TEM). The as-melt-spun ribbon was consisted of fine ${\delta}^{\prime}$ and icosahedral intermetallic compound which were precipitated in the matrix. Two exothermic peaks with the range of $120^{\circ}C-190^{\circ}C$ and $280^{\circ}C-344^{\circ}C$ corresponded to ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ precipitating reaction respectively, and two endothermic peaks with the range of $190^{\circ}C-280^{\circ}C$ and $344^{\circ}C-550^{\circ}C$ corresponded to dissolution of ${\delta}^{\prime}$ and ${\theta}^{\prime}$, S', $T_1$ respectively in DSC curves. Peak hardness value was obtained at $210^{\circ}C$ for 1 hr aging treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.138-143
• /
• 1993

Effects of aging treatment on the microstructural evolution of a rapidly solidified Al-Li-Cu alloy were investigated by differential scanning calorimetry (DSC) and transmission electron microscopy(TEM). It was found that the precipitation sequence was: supersaturated solid solution ${\alpha}^{\prime}$ ${\rightarrow}$ metastable ${\delta}^{\prime}$ + stable precipitate $T_1$ ${\rightarrow}$ stable precipitates ${\delta}+T_1$. Two exothermic and two endothermic peaks are detected by DSC analysis. The two exothermic and endothermic peaks corresponded to ${\delta}^{\prime}$ and ${\delta}+T_1$ precipitation and dissolution reactions respectively. The enthalpy of ${\delta}^{\prime}$ precipitation decreased with increasing of aging temperature and time until the finishing point of precipitation. The activation energy for precipitation of ${\delta}^{\prime}$ was measured as 80KJ/mol and the energy for dissolution was 93KJ/mol. These values arc higher than those of AI-Li binary alloy. Peak hardness value (Hv 170) was obtamed at $210^{\circ}C$ for 1hr aging treatment which coincided with finishing point of ${\delta}^{\prime}$ precipitation.

• Textile Coloration and Finishing
• /
• v.7 no.4
• /
• pp.8-15
• /
• 1995

A series of thermotropic Polyurethanes mesogenic unit were synthesized by polyaddition of a para-type diisocyanate such as 2,5-tolylene diisocyanate(2,5-TDI) with 4-4'-bis($\omega$-hydroxyalkoxy) biphenls(BPm: $HOCmH_{2m}OC_{6}H_{4}OC_{m}H_{2m}OH$ : m is the carbon number of the hydroxyalkoxy group) in DMF. Intrinsic viscosities of the polymers were in the range of 0.41~0.99dL/g DSC thermograms for these polymers exhibited two endothermic peaks corresponding to phase transitions of melting and isotropization. For examplem polyurethane 2,5-TDI/BPll with [η]=0.99 prepared from 2.5-TDI and 4,4'-bis[11-hydroxyundecaoxy biphenyl(BP11) a liquid crystalline phase from 156 to 173$^{\circ}C$. The thermotropic properites of liquid crystalline polyurethanes have been investigated by wide-angle X-ray scatter(WAXS), infrared (IR) spectroscopy, and differential scanning calorimetry (DSC). The mesomorphic behavior of the polyurethanes was concluded to be greatly dependent on the intermolecular hydrogen bonds through the urethane.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.5
• /
• pp.53-59
• /
• 2019

Solid fuel reacts with an oxidizer during combustion of a propellant to increase performance. Representative solid fuels are aluminum, cyclotrimethylenetrinitramine (RDX) and octahydro-1, 3,5,7-tetra nitro-1,3,5,7-tetrazocin (HMX). During combustion, these compounds generate white smoke by reacting with moisture and produce materials that are harmful to the environment, such as carbon monoxide, carbon dioxide, and methane gas. This study prepared a high-nitrogen-containing energetic material, hydrazinium 5-aminotetrazolate (HAT), which could be applied as a solid fuel. The compound was characterized by nuclear magnetic resonance (NMR) spectroscopy, and a thermal analysis was measured by differential scanning calorimetry (DSC). Also, the specific impulses and volumes of detonation gases were calculated using the EXPLO5 program.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.5
• /
• pp.226-232
• /
• 2021

The relationship between precipitation and coefficient of thermal expansion of Al-6%Si-0.4%Mg-0.9%Cu-(Ti) alloy (in wt.%) after various heat treatments were studied by the thermodynamic analyzer (TMA) and differential scanning calorimetry (DSC). Solution heat treatment of the alloy was carried out at 535℃ for 6 h followed by water quenching, and the samples were artificially aged in the air at 180℃ and 220℃ for 5 h. The coefficient of thermal expansion (CTE) curve showed some residual strain and decreased with increasing aging temperature. The CTE curves changed sharply in the temperature range of 200℃ to 400℃, and the corresponding peak shifted for the aged samples due to the change in the precipitation behavior of the secondary phase. These transformation peaks in the aged sample are related to the volume of the precipitation of the Si phase as determined by DSC analysis. The change in CTE is mainly caused by the precipitation of the Si phase in the Al-Si alloy, and the size of the change occurs simultaneously with the size of the precipitate.