• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.4
• /
• pp.54-69
• /
• 1991

This study deals with the position control of a hydraulic cylinder system operated by two port 3-way high speed solenoid valve in Pulse-Width-Modulation mode, instead of using conventional electro-hydraulic servovalve. Due to the complexity and the relatively poor reliability of the servovalve, an actuator using simpler and more study high speed solenoid valve will be presented. The high speed solenoid valve acts as converters of electronic pulse signal to hydraulic ones. It has been pointed out that there are practical problems to be solved in the PWM system, that is (1) accuracy of positioning control becomes considerably insufficient because the system is affected by on/off action of the solenoid valves, and (2) serious nonlinerality appears in the valve characteristics as a result of the switching behavior of the valves. As a method to overcome these defects, the differential PWM driving method of a hydraulic cylinder that improved the steady-state-error, flow rate nonlinearity in simple PWM, and the hydraulic hunting of dead time compensated-PWM driving is proposed in this study.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.741-744
• /
• 2000

In general there occur warpage in one way long part. Warpage is caused by differential shrinkage-Orientation Effect, Volumetric Shrinkage Effect, Differential Cooling Effect -over the part. Deco-Top is located at the top of 29"TV set and it's shape is one way long$(626{\times}130mm)$. Material is used transparency ABS resin. So we can't design ribs in this part. And we use film gate to avoid weld line. In these reasons we must develop no ribs and no warpage product. In this study we use MOLDFLOW's software-MF/FLOW, MF/COOL, MF/WARP. Using MF/FLOW, set the flow balance and gate positioning. And we can set cooling channel layout and the optimum processing condition through MF/COOL and MF/WARP. In result we reduced trials and obtained good product.

• Journal of the Korean Institute of Navigation
• /
• v.22 no.1
• /
• pp.1-13
• /
• 1998

Radiobeacons that carry corrections for global satellite navigation systems are currently being planned or installed in many countries. In early 1996, it was begun to send DGPS correction message from a marine radiobeacon station located in Changgi Got Lighthouse. It was the first test broadcast of DGPS correction data based on medium frequency of marine radiobeacon where transmission power and rate are 300W and 100bps respectively in Korea. However, there has not been any scientific study on the characteristic of the accuracy of a marine radiobeacon/DGPS. Accordingly, this paper investigates the accuracy of the system, which is currently operating in 310kHz. To do this , the real time differential correction in RTCM data was collected in an implemented system. And then the accuracy was analyzed related to the coverge of the radiobeacon/DGPS. As a result, it is verified that the differential positioning accuracy using the marine radiobeacon is sufficient to ensure the safety of marine activities around the coast of Korea.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2023.05a
• /
• pp.252-253
• /
• 2023

Container terminal automation might offer many potential benefits, such as increased productivity, reduced cost, and improved safety. Autonomous trucks can lead to more efficient container transport. A robust lane detection method is proposed using score-based generative modeling through stochastic differential equations for image-to-image translation. Image processing techniques are combined with Density-Based Spatial Clustering of Applications with Noise (DBSCAN) and Genetic Algorithm (GA) to ensure lane positioning robustness. The proposed method is validated by a dataset collected from the port terminals under different environmental conditions and tested the robustness of the lane detection method with stochastic noise.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.2
• /
• pp.1-8
• /
• 2007

In this research, algorithm and software for the medium frequency signal analysis of DGPS(Differential Global Positioning System) station were developed. Based on new MF(Medium Frequency) algorithm, the software of NDGPS(National DGPS) signal analysis was developed for coverage analysis. Predicted MF propagation data from this software was compared to the measurement data for the verification of a developed MF algorithm. GIS(Geographic Information System) techniques including digital map with elevation data were used because MF propagation is closely related to ground conductivity, mountains, building intensity.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.11a
• /
• pp.248-251
• /
• 1998

본 연구에서는, GPS 기준점(Optimal reference point)을 기준으로 한 DGPS(Differential Global Positioning System)와, 준 기준점(Sut-optimal reference point)을 기준으로 한 DGPS 시스템을 구현하였다. 이러한 2가지 DGPS 시스템으로부터 얻은 위치를 분석 평가하고, 그 결과를 나타냈다. 실험 결과, 준기준점을 기준으로 하는 DGPS 시스템은, 기존의 DGPS 기준국을 사용하지 않더라도 정밀 위치 측정이 가능함을 나타내었다.

• Journal of Korean Society for Geospatial Information Science
• /
• v.11 no.1 s.24
• /
• pp.61-69
• /
• 2003

The study is the open area keeping a few visible satellites and the urban area covered with the high building, an electric pole were chosen for evaluation of accuracy of satellite positioning. First, suggest the validity of RTK-GPS, RTK-GPS/GLONASS and compared the accuracy with that of the classical surveying method. As a result. In urban area, in case of real time kinematic positioning when compare between the method combined by GPS/GLONASS and by GPS alone the result of GPS/GLONASS - combination more excellent. And in open ana positioning combined GPS/GLONASS was more excellent than GPS alone in both real time differential and real time kinematic. So, RTK-GPS, RTK-GPS/GLONASS contribute to the digital mapping of Basic map and the existed map necessary for the building of PBLIS to the computerization of cadastral map in the effectiveness in time and in cost and hereafter the combined GPS/TS is expected to contribute to the development of NGIS, Re-investigation of a land register, the execution drawing on site.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.5
• /
• pp.379-388
• /
• 2019

Recently, a technique for acquiring spatial information data using UAV (Unmanned Aerial Vehicle) has been greatly developed. It is a very crucial issue of the GIS (Geographic Information System) mapping system that passes way point in the unmanned airframe and finally measures the accurate image and stable localization to the desired destination. Though positioning using DGPS (Differential Global Navigation System) or RTK-GPS (Real Time Kinematic-GPS) guarantee highly accurate, they are more expensive than the construction of a single positioning system using a single GPS. In the case of a low-priced single GPS system, the stability of the positioning data deteriorates. Therefore, it is necessary to supplement the uncertainty of the absolute position data of the UAV and to improve the accuracy of the current position data economically in the operating state of the UAV. The aim of this study was to present an algorithm enhancing the stability of position data in a single GPS mode of UAV with multiple GPS. First, the arrangement of multiple GPS receivers through the center of gravity of the UAV were examined. Next, MD (Mahalanobis Distance) is applied to detect instantaneous errors of GPS data in advance and eliminate outliers to increase the accuracy of previously collected multiple GPS data. Processing procedure for multiple GPS reception data by applying the center of the triangular method were presented to improve the position accuracy. Second, UAV navigation systems integrated multiple GPS through configuration of the UAV specifications were implemented. Using the unmanned airframe equipped with multiple GPS receivers, GPS data is measured with the TCM (Triangular Center Method). In addition, UAV equipped with multiple GPS were operated in study area and locational accuracy of multiple GPS of UAV with VRS (Virtual Reference Station) GNSS surveying were compared. The result showed that the error factors are compensated, and the error range are reduced, resulting in the reliability of the corrected value. In conclusion, the result in this paper is expected to realize high-precision position estimation at low cost in UAV using multiple low-cost GPS receivers.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.18 no.2
• /
• pp.101-110
• /
• 2000

This study focuses on examination of the availability and effectiveness about application of the differential GPS methods for navigation and acquisition of the geo-spatial information. For this, the algorithms related to a navigation solution and differential GPS were implemented in MATLAB code, a number of software simulations on test model were carried out to assess its performance, comparing the results with those obtained from the commercial software. Expecially, the results coming from tracking test on test model of the OO's WADGPS which is the commercial real-time satellite-based augmentation system via geostationary satellite (GEOs), which has been investigated with those from the above GPS methods. And also, the accuracy of absolute positioning by Navigation solution and WADGPS before and after SA-off has been compared. The above results show that DGPS methods are very reliable and efficient methods for acquisition of the geo-spatial information.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.21-26
• /
• 2006

This paper focuses on modeling and predicting differential GPS corrections transmitted by marine radio-beacon systems using artificial neural networks. Various neural network structures with various training algorithms were examined, including Linear, Radial Biases, and Feedforward. Matlab Neural Network toolbox is used for this purpose. Data sets used in building the model are the transmitted pseudorange corrections and broadcast navigation message. Model design is passed through several stages, namely data collection, preprocessing, model building, and finally model validation. It is found that feedforward neural network with automated regularization is the most suitable for our data. In training the neural network, different approaches are used to take advantage of the pseudorange corrections history while taking into account the required time for prediction and storage limitations. Three data structures are considered in training the neural network, namely all round, compound, and average. Of the various data structures examined, it is found that the average data structure is the most suitable. It is shown that the developed model is capable of predicting the differential correction with an accuracy level comparable to that of beacon-transmitted real-time DGPS correction.