• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.157-164
• /
• 2016

In this study, researchers performed preliminary design and numerical analysis for a pilot-scale helium heating system intended to support full-scale construction for a sulfur-iodine (SI) cycle. The helium heat exchanger used a liquefied petroleum gas (LPG) combustor. Exhaust gas velocity at the heat exchanger outlet was approximately 40 m/s based on computational thermal and flow analysis. The maximum gas temperature was reached with six baffles in the design; lower gas temperatures were observed with four baffles. The amount of heat transfer was also higher with six baffles. Installation of additional baffles may reduce fuel costs because of the reduced LPG exhausted to the heat exchanger. However, additional baffles may also increase the pressure difference between the exchanger's inlet and outlet. Therefore, it is important to find the optimum number of baffles. Structural analysis, followed by thermal and flow analysis, indicated a 3.86 mm thermal expansion at the middle of the shell and tube type heat exchanger when both ends were supported. Structural analysis conditions included a helium flow rate of 3.729 mol/s and a helium outlet temperature of $910^{\circ}C$. An exhaust gas temperature of $1300^{\circ}C$ and an exhaust gas rate of 52 g/s were confirmed to achieve the helium outlet temperature of $910^{\circ}C$ with an exchanger inlet temperature of $135^{\circ}C$ in an LPG-fueled helium heating system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.51 no.4
• /
• pp.276-283
• /
• 2013

Purpose: The purpose of this study was to investigate the fit and screw joint stability between Ready-made abutment and CAD-CAM custom-made abutment. Materials and methods: Osstem implant system was used. Ready-made abutment (Transfer abutment, Osstem Implant Co. Ltd, Busan, Korea), CAD-CAM custom-made abutment (CustomFit abutment, Osstem Implant Co. Ltd, Busan, Korea) and domestically manufactured CAD-CAM custom-made abutment (Myplant, Raphabio Co., Seoul, Korea) were fabricated five each and screws were provided by each company. Fixture and abutments were tightening with 30Ncm according to the manufacturer's instruction and then preloding reverse torque values were measured 3 times repeatedly. Kruskal-Wallis test was used for statistical analysis of the preloading reverse torque values (${\alpha}=.05$). After specimens were embedded into epoxy resin, wet cutting and polishing was performed and FE-SEM imaging was performed, on the contact interface. Results: The pre-loading reverse torque values were $26.0{\pm}0.30Ncm$ (ready-made abutment; Transfer abutment) and $26.3{\pm}0.32Ncm$ (CAD-CAM custom-made abutment; CustomFit abutment) and $24.7{\pm}0.67Ncm$ (CAD-CAM custom-made abutment; Myplant). The domestically manufactured CAD-CAM custom-made abutment (Myplant abutment) presented lower pre-loading reverse torque value with statistically significant difference than that of the ready-made abutment (Transfer abutment) and CAD-CAM custom-made abutment (CustomFit abutment) manufactured from the same company (P=.027) and showed marginal gap in the fixture-abutment interface. Conclusion: Within the limitation of the present in-vitro study, in domestically manufactured CAD-CAM custom-made abutment (Myplant abutment) showed lower screw joint stability and fitness between fixture and abutment.

• Journal of Korean Society of Forest Science
• /
• v.64 no.1
• /
• pp.33-41
• /
• 1984

This study was conducted to examine the physiology of pine mushroom mycelia cultured with various media for artificial culture of pine mushroom. The results obtained were as follows: 1) Among the various media, the medium composed of honey, boiled pine mushroom and soil extract fluid, fibrous root extract fluid, dry yeast, $KH_2PO_4$ inositol, folic acid, and biotin was the best for the growth of pine mushroom mycelium. 2) The optimum temperature for germinating pine mushroom spore and for culturing pine mushroom mycelium, was $24^{\circ}C$ and the optimum pH was 4.5. 3) There was no significant difference in growth between the mycelium separated from the tissue of pine mushroom sporophore and that separated from the spore. 4) No noticeable effect was found on the growth if such salts as $ZnSO_4$, $MnSO_4$, $MgSO_4$, $CaCl_2$ and ferric citrate were added to the Hamada's medium. 5) The addition of fibrous root extract promoted the growth of pine mushroom mycelium. 6) As a carbon source of artificial media, honey was more effective than glucose. 7) The culture infiltration of Mortierlla growing often in Fairy Ring was good for the growth of mycelium compared with the control. 8) The addition of fibrous root extract, inositol, biotin, and folic acid to artificial culture media was greatly effective in growth. When the temperature was lowered $19^{\circ}C$ after mycelium has appeared, the formation of primordium was observed.

• Journal of Chest Surgery
• /
• v.43 no.6
• /
• pp.596-601
• /
• 2010

Background: This study was designed to evaluate the efficacy of a mixture of hyaluronic acid and sodium carboxymethyl cellulose ($Guardix-sol^{(R)}$) on experimental pericardial adhesion. Material and Method: Thirty rats were divided into 2 groups of 15 rats each and pericardial mesothelial injury was induced during surgery by abrasion. In the control group, blood and normal saline were administered into pericardium; in the test group, blood and HA-CMC solution were administered. Pericardial adhesions were evaluated at 2 weeks (n=5), 4 weeks (n=5), and 6 weeks (n=5) after surgery. The severity of adhesions was graded by macroscopic examination, and the adhesion tissue thickness was analyzed microscopically with Masson trichrome stain and an image processing program. Result: The test group had significantly lower macroscopic adhesion scores ($2.9{\pm}0.6$ : $3.9{\pm}0.4$, p<0.000) compared with the control group. For microscopic adhesion tissue thickness, the test group had lower scores compared with the control group, but this difference was not statistically significant ($91.73{\pm}49.91$ : $117.67{\pm}46.4$, p=0.106). Conclusion: We conclude that an HA-CMC solution ($Guardix-sol^{(R)}$) reduces the formation of pericardial adhesions in this animal model.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.3
• /
• pp.22-30
• /
• 2013

This study aims to measure the thermal comfort effects of urban street trees. As the usual dry bulb air temperature does not indicate properly how the average pedestrian feels the heat of a typical summer day under the strong sunshine, we adopted the Wet Bulb Globe Temperature(WBGT). WBGT involves black globe temperature to measure the direct radiation of sun beams on our bodies, for example our heads. We measured temperatures on very sunny and hot summer days, August 3, 4, and 7, 2012, on the urban streets of Seoul, Korea. Wet bulb, globe, and dry bulb temperatures were measured under direct sunlight from 1 O'clock to 5 O'clock pm. Globe and dry bulb temperatures were measured under street tree shades nearby during the same hours. Then the WBGTs were calculated with the formulae, one for sunny outdoor spaces, and the other for shaded outdoor spaces or indoor. The results are compared with the Korean Standards Association(KS A ISO 7243). The major findings were: 1) On very sunny and hot summer days in Seoul, street tree shades lower the WBGT about 1 to 4 degrees, 2) during the hours of 3 and 4 O'clock in the afternoon, the WBGT under the tree shades are about 3 to 4 degrees lower compared to those under sunshines(approx. 29 to 32 degrees respectively), 3) This difference makes a major thermal comfort for urban pedestrians because senior citizens or weak persons are recommended to move indoor, and even healthy people are recommended stop outdoor sports and take rests in the shades when WBGT is about 32. On the other hand, if the WBGT is around 29, or 3 degrees lower, slower walking, light works or sports are allowable, 4) On site questionnaire survey confirms the thermal comforts under the tree shades, and we even could not get survey subjects on the sunny parts of the sidewalks, 5) We strongly recommend change of guidelines for urban street trees from "one row of street trees on 6m~8m intervals" to "street trees to make continuous shades".

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.3
• /
• pp.193-202
• /
• 2016

Purpose: This study was performed in order to assess the effect of the surface treatment methods and the use of bonding agent on the shear bond strength (SBS) between the aged CAD-CAM (computer aided design-computer aided manufacturing) hybrid materials and added composite resin. Materials and methods: LAVA Ultimate (LU) and VITA ENAMIC (VE) specimens were age treated by submerging in a $37^{\circ}C$ water bath filled with artificial saliva (Xerova solution) for 30 days. The surface was ground with #220 SiC paper then the specimens were divided into 9 groups according to the combination of the surface treatment (no treatment, grinding, air abrasion with aluminum oxide, HF acid) and bonding agents (no bonding, Adper Single Bond 2, Single Bond Universal). Each group had 10 specimens. Specimens were repaired (added) using composite resin (Filtek Z250), then all the specimens were stored for 7 days in room temperature distilled water. SBS was measured and the fractured surfaces were observed with a scanning electron microscope (SEM). One-way ANOVA and Scheffe test were used for statistical analysis (${\alpha}=.05$). Results: Mostly groups with bonding agent treatment showed higher SBS than groups without bonding agent. Among the groups without bonding agent the groups with aluminum oxide treatment showed higher SBS. However there was no significant difference between groups except two subgroups within LU group, which revealed a significant increase of SBS when Single Bond Universal was used on the ground LU specimen. Conclusion: The use of bonding agent when repairing an aged LAVA Ultimate restoration is recommended.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.46 no.1
• /
• pp.1-8
• /
• 2018

The purpose of this study was to investigate the effects of light intensity on the initial growth response of three woody plants for indoor landscaping; Ardisia pusilla, Clusia rosea and Fatsia japonica. The plants were planted in 10cm pots, the light intensities used were of four levels-15, 30, 60, $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD-and light irradiation time was set to 12/12 (day/night). Growth responses including plant height, leaf length, leaf width, chlorophyll fluorescence (Fv/Fm), SPAD and Hunter values were measured at 4-week intervals, and shoot weight and root weight of fresh and dry plants were measured after completion of the experiment. Fatsia japonica tended to show greater leaf length and leaf width as light intensity became greater, while other plants did not show any significant differences at different light intensities. The Fv/Fm value of the Ardisia pusilla was found to be stressed at 60 and $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, while the Fv/Fm values were within normal range with other plants or at other light intensity levels to show no stress. Only Clusia rosea showed significantly different SPAD values at $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, and there was no significant SPAD value difference found with other plants or at other light intensity levels. While Hunter values of the Ardisia pusilla did not show any significant differences at any light intensity levels, Clusia rosea and Fatsia japonica showed specificity in L, a and b values at 60 and $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, respectively. Ardisia pusilla showed a big stem growth at $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, and Clusia rosea showed a steady growth at 60 and $120{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$.

• Journal of dental hygiene science
• /
• v.5 no.2
• /
• pp.83-88
• /
• 2005

In spite of relatively low level of radiation dose used at dental clinics, long term exposure may be harmful, so radiation workers at dental clinics must be well aware of its danger. This study was radiation safety management by dental hygienists in order to take preventive measures for dental hygienists and suggest ideas to develop radiation safety training programs. For this, we contacted dental hygienists working at the local dental clinics for 4 months from December of 2003 to march of 2004 and obtained the following findings. 1. Regarding the intraoral radiographic method, the average daily photographing frequency of standard films stood at one to five pieces (47.5%), and the average weekly photographing frequency of digital radiation medicine stood at less than one piece (69.8%), and the average weekly photographing frequency of bitewing films stood at less than one piece (67.7%), and and the average weekly photographing frequency of occlusal films stood at less than one piece (95.5%), and the dentistries whose average weekly photographing frequency of pediatric films stood at one to five pieces accounted for 47.1 percent. 2. Regarding the extraoral radiographic method, the average weekly photographing frequency of panorama film stood at one to five pieces (63.7%), and less than one piece (20.9%), the average weekly photographing frequency of cephalometric film stood at less than one piece (72.3%), and one to five pieces (20.1%). 3. Concerning the radiation safety management training program, only 18.7% of total 278 surveyed attended the training progra., Attendance tendency of the training program by general characteristics showed statistically significant difference according to age (p<0.01), working experience (p<0.001), and marital status (p<0.01). 4. When asked about the protective equipments against radiation exposure, 40.6% of them said "modest", and 71.1% appeared equipped with led apron as a protective tool.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.5
• /
• pp.65-73
• /
• 2015

The purpose of this study was to compare the Mean Radiant Temperature(MRT) under two landscaping shade membranes, white and black, with those of natural outdoor spaces at summer midday. An additional perforated black shading net was applied and compared for the consideration of the practical application. The average MRT at the height of 2.4m, 10cm below the membranes of black, white, and perforated black were $49.1^{\circ}C$, $41.6^{\circ}C$ and $36.8^{\circ}C$ respectively, while that of open sky was $41.8^{\circ}C$. This indicates that a closer position to the darker membrane caused a higher MRT. At the height of 1.1m and 1.7m, the difference of MRT between the black and the white membranes was slight, while the value of white was unexpectedly higher than the black. The MRT of black perforated net showed the lowest value at every height. The black membrane absorbed more solar radiation than the white, which caused the greater release of long wave radiation and higher temperature near the membrane itself. In spite of the higher albedo of the white membrane, the higher solar radiation transmittance rate of which seemed to cause the slightly higher MRT than the black at the hight of 1.1m and 1.7m. In summary, the performance of the black membrane was slightly better than the white in terms of the air conditioning of the human related space around the height of 1.1m and 1.7m, when the shading membranes were at 2.5m height.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.527-536
• /
• 2016

This study aims to generate baseline data for vitalizing the sales of functional cosmetics through an Importance-Performance Analysis (IPA) of the selection attributes of functional cosmetics. From the analysis of consumers' selection criteria, the study will assist functional cosmetics companies in reflecting consumer demands and therefore securing competitiveness. For this, general consumers aged over 20 years were surveyed for 5 weeks from Feb 23 through Mar 30, 2015, and 447 empirical data (response rate 88.9%) were processed through SPSS WIN 21.0 program for analysis. To conduct gender difference analysis on the IPA of the selection attributes of functional cosmetics, 17 selection attributes were categorized into 4 factors: functionality, labeling, popularity, and product. Cronbach's alpha for all factors was 0.5, proving the internal consistency and reliability of the survey. The survey results showed that while the entire average came out significantly higher for females (5.89/7points) than for males (5.66/7points) (p<0.001), the selection attributes 'anti-wrinkling', 'whitening function', 'functionality', 'expiration date', 'full ingredient labeling system' and 'various promotional events' showed significant gender differences. IPA results pertaining to gender showed 'price', 'functionality', 'spreadability' and 'full ingredient labeling system' as 2nd quadrant attributes, whereas female consumers selected 'price', 'whitening function', 'anti-wrinkling', 'functionality' and 'full ingredient labeling system' as attributes. Results show that businesses in the field of cosmetics and related areas need to prioritize improving the following factors that received low satisfaction from all consumers: 'price', 'functionality', and 'total labeling.' In particular, the 'price' aspects are considered to require reasonable and affordable pricing.