• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.323-327
• /
• 1999

Most of the underwater noise emitted by small fishing boat are owing to vibration of main engine and generator etc.. This paper describe on the spectrum analysis of underwater noise by engine generating in small fishing boat in order to build up comfortable environment for fisheries man and to reduce ambient noise. The obtained results are summerized as follows:1. When the underwater noise of 10ton class fishing boat measure and the frequency spectrum in varied revolution of engine 750, 900, 1000rpm analyze, the frequency pattern is similar to each other, the faster revolution of engine increase, the higher frequency spectrum level becomes. 2. In comparison of spectrum level of underwater noise between 10ton class and 14ton class fishing boat, the former level is higher than the latter. 3. Frequency spectrum pattern of two 14ton class fishing boat is similar to each other but spectrum level is a little difference, it is suggested to different by fitting condition of engine.

• Journal of the korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.39-47
• /
• 1988

A disk photo sensor system was constructed and installed on engine for the crank angle measurement. Statically measured TDC crank angle data were compared with those obtained from engine motoring. Two groups of cylinder pressure data were compared each other, one measured by pressure transducer mounted flush on the combustion chamber and the other obtained with the help of spark plug type adaptor. A simple analysis on the gas flow in the spark plug type pressure transducer displayed reasonably good agreement with those from engine motoring tests. In various firing tests, the IMERs obtained from the spark plug type pressure transducer turned out to be higher than those from the flush mounted one at low engine speed while those two were nearly the same at high engine speed. As the engine load decreased the relative difference in IMEP measurement between the two types tended to be enlarged.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.34-37
• /
• 2012

In this paper, configurations and performance of a pulse tube engine (PTE) are investigated. The configuration of PTE is basically designed by using a concept of energy flow. The configurations of PTE are classified as a PTE with two pistons and a PTE with one piston. First, the PTE with two pistons is simulated and the Carnot efficiency is about 41 %. The phase difference of between motion of two pistons located at expander and compressor mainly effects the performance of the PTE. Second, the PTE with one piston is designed. From a concept of analogy, the piston of compressor is replaced by a compliance tube and a resonator. The PTE with one piston is identical with a thermoacousic engine and has the large volume because the compliance tube and resonator are consisted of large volume tubes. Therefore, we will consider each usefulness of the compact PTE with two pistons and the huge PTE with one piston for PTE applications and the judgement of feasibility.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.28 no.1
• /
• pp.45-52
• /
• 1992

In this paper, combustion characteristics and engine performance varying with blending rate of fish oil using five test fuels, e.g.pure diesel oil and four types of sardine-oil-blended diesel oils, their blending rates by weight being 20%, 40%, 60% and 80% respectively, and operating condition of engine, were investigated experimentally both in the constant volume combustion bomb and in the engine. The results are summarized as follows: 1) In the bomb, the influence of temperature on ignition delay of sardine-oil-blended diesel oils was larger than that of pure diesel oil, and it tended to increase as the blending rate of fish oil increase sardine-oil-blended diesel oils. As far as the influence of pressure on ignition delay concerns, there was no significant difference with all the test fuels. 2) In the engine, the ignition delay of fish-oil- blended diesel oils was longer than that of pure diesel oil, and it tended to increase as the blending rate increases. In the bomb, the ignition delay in high temperature showed no significant difference between with pure diesel oil and with fish-oil-blended diesel oils, and it was especially short with 60% fish-oil-blended diesel oil. In low temperature, however, the delay became longer as the blending rate increase. 3) The combustion duration was shorter with fish-oil-blended diesel oils than with pure diesel oil and it became a little shorter as the blending rate increases. 4) The rate of fuel consumption showed no significant difference between with fish-oil-blended diesel oils and with prue diesel oil, although calorific value of fish oil was lower than that of diesel oil. 5) Smoke density in exhaust gas was lower with fish-oil-blended diesel oils than with pure diesel oil and the higher the blending rate was, the lower the smoke density became.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.529-536
• /
• 2002

The performance of stilting engine, in particular, its energy conversion efficiencies are critically influenced by the regenerator characteristics. The regenerator characteristics are influenced by effectiveness, void fraction. heat transfer loss and fluid friction loss in the regenerator matrix. These factors were influenced by the surface geometry and material properties of the regenerator matrix. The regenerator design goals arc good heat transfer and low pressure drop of working Bas across the regenerator. Various data for designing a wire screen matrix have been given by Kays and London(1984). The mesh number of their experiment. however, was confined below the No. 60. which seems rather small for the Stirling engine applications. In this paper. in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed mettled of matrix in oscillating flow as the same condition of operation in a Stirling engine. Seven kinds of sing1e wire screen meshes were used as the regenerator matrices. The results are summarized as follows; 1. While the working fluid flew slowly in the regenerator. the temperature difference was great at the both hot-blow(the working fluid flows from healer to cooler) and cold-blow(the working fluid flows from cooler to healer). On the other hand. while the working fluid flew fast. the temperature difference was not distinguished. 2. The No.150 wire screen used as the regenerator matrix showed excellent performance than tile others. 3. Phase angle variation and filling rate affected heat transfer or regenerator matrices. 4. Temperature difference between the inlet and outlet of the regenerator is very hish in degree of 120 phase angle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.23-28
• /
• 2011

The engine ground and altitude tests were carried out to investigate the effect of jet fuel alteration on the performance of a small turbojet engine. JP-S was supplied 8% higher than JP-8 by fuel metering system at the same command. The employment of JP-S showed the similar starting characteristic to that of JP-8, however, difference in the ignition time and acceleration rate of engine speed due to the difference of fuel flow rate by fuel metering system was observed. In spite of jet fuel alteration, the test results yield the similar steady-state engine performance in net thrust, air flow, exhaust gas temperature, etc. On the other hand, the fuel consumption of JP-S increased by 5 % compared with that of JP-8. In point of specific fuel consumption (SFC), SFC of JP-S was approximately 1.1~2.6 %, 5 % higher than that of JP-8 in ground and altitude tests respectively at the same thrust.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.410-415
• /
• 2010

The engine ground and altitude tests were carried out to investigate the effect of jet fuel alteration on the performance of a small turbojet engine. JP-S was supplied 8% higher than JP-8 by fuel metering system at the same command. The employment of JP-S showed the similar starting characteristic to that of JP-8, however, difference in the ignition time and acceleration rate of engine speed due to the difference of fuel flow rate by fuel metering system was observed. In spite of jet fuel alteration, the test results yield the similar Steady-State engine performance in Net thrust, Air flow, Exhaust Gas Temperature, etc. On the other hand, the Fuel consumption of JP-S increased by 5 % compared with that of JP-8. In point of Specific Fuel Consumption (SFC), SFC of JP-S was approximately 1.1~2.6 %, 5 % higher than that of JP-8 in ground and altitude tests respectively at the same thrust.

• Journal of Korea Multimedia Society
• /
• v.14 no.3
• /
• pp.356-367
• /
• 2011

In this paper, we proposed a new car engine sealing inspection system based on image processing and understanding. The car engine sealing inspection plays very important role for protecting leakage caused by inappropriate sealing, which is a crucial point for productivity of car engines. The proposed inspection system has been aimed to enhance the previously proposed sealing inspection systems based on image processing, which have high computation complexity and low performance for correctly inspecting some contamination by oil with similar color with that of sealing. Moreover, the previously proposed system has a difficulty in installing the camera system on the sealing machine. The proposed system considers a difference of images before and after sealing obtained from one static camera. By utilizing a difference of images, the proposed system shows very robust performance using a proposed simple depth checking algorithm for some contamination cases by oil with similar color with that of sealing and the total inspection system is simple and cheap to implement. According to the experiments conducted in a real car product line, the proposed inspection system shows better inspection performance and needs smaller implementation cost than three other previously proposed system working in current car sealing inspection systems.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.122-128
• /
• 2001

The simulation analyses of a dish solar power system with stirling engine in this study are applied to system performance prediction if four different test sites; Seoul, Pusan and Cheju in Korea, and Naha in Japan. The effects of difference of concentrator type such as monolithic and stretched-membrane construction on system efficiency are also evaluated. The total amount of generated power for a year depends on the site. However the total maximum system efficiency in every site is approximately 16% and there isnt striking difference. It is also found that the maximum collector efficiency of stretched-membrane concentrator is about 3∼15% lower than that of the monolithic type.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.6
• /
• pp.688-694
• /
• 2002

Several methods were developed for on-line measuring oil consumption in gasoline engine using an oil consumption meter. The oil consumption meter indicates the oil quantity by real-time-measuring the oil level in the sump. In order to measure the oil consumption, the oil consumption meter proposed in this paper requires shorter time, less additional procedures, and shows better results than the traditional drain method. Under steady-state engine-operating conditions, the results obtained through the regression or the difference method show an good agreement with those through the drain method. Under transient engine-operating conditions, on the other hand, good results can be obtained through the reference method.