• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.4 s.109
• /
• pp.329-338
• /
• 2006

The resilient mounts of a diesel engine installed onboard a ship should be designed for both static and dynamic loads. If possible, the resonance frequencies of the six rigid body modes of the installation and the flexible modes of the engine support structure should not lie within the engine operation range. In this paper a design criterion is proposed to evaluate an isolation system which involves the summation of dynamic forces transmitted through the resilient mounts and elastic potential energy index stored in the mounts. A case study is also presented in which a diesel engine generator, which had an elastic foundation and was mounted in a 5500 TEU container vessel, was studied both theoretically and experimentally. The theoretical analysis of the test model was performed by using a single mass 6 degree of freedom system. Actual measurements of mechanical vibration of the engine and its foundation onboard were carried out, which showed the importance of including the flexibility of the engine support structure in the mode.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.8-22
• /
• 1995

Three dimensional numerical study of non-evaporating and evaporating spray characteristics was performed in a quiescent and motoring condition of direct injection diesel engine. The calculation parameter was breakup model. The breakup models used were Reitz & Diwakar model and TAB model. The modified k-${\varepsilon}$ turbulence model considering the compressibility effect due to the compression and expansion of piston was used. The calculation results of the spray tip penetration and tip velocity using the TAB model showed similar trends comparing with the experimental data. Although the evaporation rate was not nearly affected with the breakup model at the higher injection pressure, in the low injection case, the evaporation rate result using the TAB model became higher than that of R&D model. The evaporation rate was increased with the injection pressure due to the vigorous interaction with the gas field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.122-129
• /
• 2004

Finite element analysis was performed to analyze structural safety of a new heavy-duty direct injection diesel engine. A half section of the in-line 6-cylinder engine was selected as a computational domain. A mapping method was used to project heat transfer coefficients from CFD results of engine coolant flow onto the FE model. The accurate setting of thermal boundary condition on the FE model was expected to result in improved prediction of temperature, cylinder bore distortion, and stresses. Characteristics of high cycle fatigue were investigated by assuming the engine was operated under the following five loading conditions repeatedly; assembly force, assembly force with thermal loading, alternating maximum gas pressure loading at each cylinder combined with assembly force and thermal loading. Distribution of fatigue safety factor was calculated by using it Haigh diagram in which the maximum and the minimum stresses were selected from the five loading cases.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.135-144
• /
• 2005

The Effects of intake swirl and combustion parameters on the performance and emission characteristics in a V8 type turbocharged intercooler D.I. diesel engine of the displacement $16.7\iota$ were studied experimentally in this paper. Generally the swirl in the combustion process of diesel engine promotes mixing of the injection fuel and the intake air. Also, TCI diesel engine is put to practically use intercooler in order to increase boost efficiency which is cooled boost air. As a result of steady flow test, when the swirl ratio is increased, the mean flow coefficient is decreased, whereas the Gulf factor is increased. And through engine test, its can be effected to meet performance and emission by optimizing the main parameters; the swirl ratio is 2.25, compression ratio is 17.5, combustion bowl is re-entrant $8.5^{\circ}$, nozzle hole diameter is $\phi0.33^{\ast}3+\phi0.35^{\ast}2$, injection timing is BTDC $12^{\circ}CA$ and turbocharger is T02 model which are compressor 0.6A/R+46trim and turbine 1.0A/R+57trim.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.97-105
• /
• 1998

High pressure injection is recently used to reduce the emissions and increase the power of DI diesel engine. This high pressure injection makes the spray strike the cylinder wall. This spray/wall impingement is known to affect the emission and performance of DI diesel engine such that it is very important to know the spray/wall impingement process. In this study, multidimensional computer program KIVA-II was used to clarify the effect of spray wall impingement by different injection spray angle with the spray/wall impingement model consiedering rebound and slide motion and also the improved submodel for liquid breakup, drop distortion model.

• Journal of Power System Engineering
• /
• v.7 no.1
• /
• pp.14-19
• /
• 2003

A diesel engine has been widely used for ship and industry power because it has many merits of high thermal efficiency, reliability and durability. However its exhaust gas is harmful to human and air environment. Reducing the hurtful exhaust gas emissions, the study of the gas flow in the inlet and exhaust manifold is in progress in the world. In this paper we modeled the gas flow as one dimensional isentropic flow to predict the gas flow in the exhaust manifold. The method of characteristics was used for the model calculation, and the calculated results were compared with the experimental ones.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.3 s.258
• /
• pp.338-343
• /
• 2007

Thermal deformation of cast iron exhaust manifold for turbo diesel engine is investigated by finite element analysis (FEA). The FE model included the temperature dependent material properties as well as the interactions between exhaust manifold, cylinder head and fasteners. It also considers the sliding behavior of the flanges of exhaust manifold on cylinder head when either expansion or contraction of the exhaust manifold exceeds the fastener pretension. The result of analysis revealed that remarkable thermal deformation along the longitudinal direction. Compressive plastic deformation at high temperature remained tensile stress in manifold and resulted in longitudinal contraction at ambient temperature. The amount of contraction at each fastener position was predicted and compared with experimental results. Analysis results revealed that the model predicted deformation qualitatively, but more elaborated cyclic hardening behavior would be necessary to predict the deformation quantitatively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.5
• /
• pp.63-70
• /
• 1993

In 1980's to 1990's the marine propulsion diesel engines have been developed into lower speed and longer stroke for the energy saving(small S.F.O.C.). As these new trends the convetional mechnical-hydraulic governors were not adapted to the new requirements and the digital governors have been adopted in the marine use. The digital governors usually use the control algorithms such as the PID control, optimal control, adaptive control and etc. While the engine has delay time and parameter variations these control algorithms have difficulty in considering the stability and the robustness for the model uncertainty. In this study, the $H_{\infty}$ controller design method are applied to the speed control of the low speed marine diesel engine. By comparison the $H_{\infty}$ control results with the PID control results, the validity of the $H_{\infty}$ controller under the delay time and parameter variations is confirmed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.94-103
• /
• 1999

A model for the prediction of combustion and exhaust emissions of DI diesel engine has been formulated and developed . This model is a quasi-dimensional phenomenological one and is based on multi-zone combustion modelling concept. It takes into consideration, on a zonal basis ,detailed of fuel spray formation, droplet evaporation, air-fuel mixing, spray wall interaction, swirl , heat transfer, self ignition and burning rate . The emission model is considered with chemical equipment , as well as the kinetics of fuel. NO and soot reactions in order to calculate the pollutant concentrations within each zone and the whole of cylinder . The accuracy of prediction versus experimental data and the capability of the model in predicting engine heat release, cylinder pressure and all the major exhaust emissions on zonal and cumulative basis., is demonstrated. Detailed prediction results showing the sensitivity of the model bv various injection rates are presented and discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.14-21
• /
• 2011

In diesel engines, accurate EGR control is important due to its effect on nitrogen oxide and particulate matter emissions. Conventional EGR control system comprises a PI feedback controller for tracking target air mass flow and a feedforward controller for fast response. Physically, the EGR flow is affected by EGR valve lift and thermodynamic properties of the EGR path, such as pressures and temperatures. However, the conventional feedforward control output is indirectly derived from engine operating conditions, such as engine rotational speed and fuel injection quantity. Accordingly, the conventional feedforward control action counteracts the feedback controller in certain operating conditions. In order to improve this disadvantage, in this study, we proposed feedforward EGR control algorithm based on a physical model of the EGR system. The proposed EGR control strategy was validated with a 3.0 liter common rail direct injection diesel engine equipped with a DC motor type EGR valve.