• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.07a
• /
• pp.201-201
• /
• 1997

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.1
• /
• pp.15-21
• /
• 2002

We investigated effects of electrical, physical, and chemical parameters on energy transfer, NO conversion, and light emission in the dielectric barrier discharge (DBD) process. As gap distance between electrodes increased, discharge onset voltage increased. However, as gap distance between electrodes increased, electric field which initiates discharge showed approximately the same value, 30kV/cm. The discharge onset voltage of the coarse surface electrode was lower than that of the smooth surface electrode. And, energy transfer was slightly enhanced in the coarse electrode condition. However, NO conversion rate decreased with the coarse surface electrode because more uniform discharge can be obtained on the smooth surface electrode. The NO conversion rate increased with decreasing the initial concentration, so the DBD process is more feasible in the lower concentration condition. The variation of gas residence time tested at the same energy density in the experiment did not affect on the NO conversion. The result shows that the NO conversion rate mainly depends on the energy density. The DBD process is able to adjust on plasma-photocatalyst process because it emits the short wavelength light in the range of ultraviolet. The intensity of light emission increased with the increase of the energy transfer to the reactor and the gas flow rate.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.4
• /
• pp.529-536
• /
• 2004

Innovated technique to inactivate microorganisms has been developed. This technique uses plasma discharge in 2-phase (Air-Water). Dielectric Barrier (two phase) Discharging system is able to produce new oxidants for microorganisms. Products from discharging are $HNO_2$, $NO_2{^-}$, $HNO_3$, $NO_3{^-}$ and ozone but many other radicals can be generated as well. DBD water has low concentration of ozone (about 0.5mg/L), $NO_2{^-}$, $NO_3{^-}$ (about 10mg-N/L, 20mg-N/L respectively) and lots of $H^+$. These products play an important role in oxidation. Oxidation power by KI titration methods is approximately equivalent to $50mg-O_3/L$. Surprisingly stored DBD water could oxidize KI and maintain stable pH (about pH3) even after several days. Stored DBD water for 5 days has also more than 4log disinfection power to E. coli. However, DBD water cannot be used for drinking water directly due to it's toxicity. Additional process to neutralize pH and decrease toxicity must be applied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.263-263
• /
• 2011

본 연구에서는 DBD (Dielectric Barrier Discharge)방식의 상압 플라즈마를 이용하여 FPD (flat panel display) 공정에 사용되는 a-Si, Si3N4의 식각 공정 특성을 평가하였다. 사용된 DBD 반응기는 기존의 blank planar plate 형태의 Power가 인가되는 anode 부분과 Dielectric Barrier 사이 공간을 액상의 도전체로 채워 넣은 형태의 전극이 사용 하였으며, 인가 Power는 40kHz AC 최대인가 전압 15 kVp를 사용 하였다. 방전 가스는 N2, 반응가스로는 CDA (Clean Dry Air)와 NF3, 액상의 Etchant를 사용 하였으며 모든 공정은 In-line type으로 시편을 처리 하였다. NF3의 경우 30 mm/sec 이송속도 1회 처리 기준 a-Si 1300${\AA}$, Si3N4 1900${\AA}$의 식각 두께를 보였으며 a-Si : Si3N4 선택비는 N2, CDA의 조절을 통하여 최대 1:2에서 4:1 정도까지 변화가 가능하였다. 균일도는 G2 (370 mm${\times}$470 mm)의 경우 5.8 %의 균일도를 보이고 있다. 이외에도 NF3 공정의 경우 실제 TFT-LCD 공정 중 n+ channel (n+ a-Si:H)식각 공정에 적용하여 5.5 inch LCD panel feasibility를 확인 할 수 있었다. 액상 Etchant (HF수용액, NH4HF2)는 버블러를 사용하여 기화 시켜 플라즈마 소스를 통해 1차적으로 활성화 시키고 기존 DBD 반응기에 공급해 주는 형태로 평가를 진행하였다. 식각 특성은 30mm/sec 이송속도에서 a-Si $25{\AA}$ 정도로 가스 형태의 Etchant에 비해 매우 낮은 수준이나 Etching rate 향상을 위한 factor 파악 및 개선을 위한 연구를 진행 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1061-1064
• /
• 2001

Deep Interests have been paid on the application of non-thermal plasma technique to solve the environmental pollution problems. $CO_2$, is one of the severe pollutants which cause the acid rain and global warming. In this study, in order to improve the conversion efficiency of $CO_2$, the streamer corona discharge plasma and barrier discharge plasma reactors were made, and the conversion characteristics of $CO_2$by the corona discharge plasma and some discharge characteristics of these discharge chambers are studied experimentally.

• Applied Science and Convergence Technology
• /
• v.27 no.2
• /
• pp.23-25
• /
• 2018

With respect to the electrode structure and the discharge characteristics, the atmospheric pressure plasma sheet of a thin polyimide film is introduced in this study; here, the flexible plasma device of a dielectric-barrier discharge with the ground electrode and the high-voltage electrode formulated on each surface of a polyimide film whose thickness is approximately $100{\mu}m$, that is operated with a sinusoidal voltage at a frequency of 25 kHz and a low voltage from 1 kV to 2 kV is used. The streamer discharge is appeared along the cross-sectional boundary line between two electrodes at the ignition stage, and the plasma is diffused on the dielectric-layer surface over the high-voltage electrode. In the development of a plasma sheet with thin dielectric films, the avoidance of the insulation breakdown and the reduction of the leakage current have a direct influence on the low-voltage operation.

• Journal of Environmental Science International
• /
• v.21 no.5
• /
• pp.597-603
• /
• 2012

Non-thermal plasma processing using a dielectric barrier discharge (DBD) has been investigated as an alternative method for the degradation of non-biodegradable organic compounds in wastewater. The active species such as OH radical, produced by the electrical discharge may play an important role in degrading organic compound in water. The degradation of N, N-Dimethyl-4-nitrosoaniline (RNO) was investigated as an indicator of the generation of OH radical. The DBD plasma reactor of this study consisted of a plasma reactor, recycling pump, power supply and reservoir. The effect of diameter of external reactor (15 ~ 40 mm), width of ground electrode (2.5 ~ 30 cm), shape (pipe, spring) and material (copper, stainless steel and titanium) of ground electrode, water circulation rate (3.1 ~ 54.8 cm/s), air flow rate (0.5 ~ 3.0 L/min) and ratio of packing material (0 ~ 100 %) were evaluated. The experimental results showed that shape and materials of ground were not influenced the RNO degradation. Optimum diameter of external reactor, water circulation rate and air flow rate for RNO degradation were 30 mm, 25.4 cm/s and 4 L/min, respectively. Ground electrode length to get the maximum RNO degradation was 30 cm, which was same as reactor length. Filling up of glass beads decreased the RNO degradation. Among the experimented parameters, air flow rate was most important parameters which are influenced the decomposition of RNO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.904-907
• /
• 2002

In this study, the plasma-assisted $CO_2$ conversion characteristics were investigated in the streamer corona discharge and silent discharge reactors with dielectric of $Al_2O_3$, to improve the conversion efficiency $CO_2$. Some discharge characteristics of $CO_2$ as parameters of gap spacing and applied voltage frequency, in both corona and silent discharge reactor were also obtained. The maximum $CO_2$ conversion rate was 10.1 [%] under the 5.2 [W] of discharge power and 250 [Hz] of applied voltage frequency.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.379-382
• /
• 2000

The characteristics of Xe discharge lamp(Mercuryless lamp) are described in this paper. In this paper, FFL is operated by sine wave and pulsed source. We apply V-Q Lissajous' figure for the discharge measurements of FFL which has the electrodes covered with dielectric. When FFL is operated by sine wave source, the characteristics are similar to DBD(Dielectric Barrier Discharge) and SD(Silent Discharge). And we compared the characteristics of FFL which is operated with sine wave and pulsed discharge by using V-Q Lissajous' figure method. When FFL is operated with pulsed, the discharge current flows after the applied voltage is risen. As the duty ratio increases the electric field becomes strong and much more xenon ions are produced. And the number of metastable xenon atoms seem to increase, therefore, the phosphor radiation after the cut off of voltage increases compared with the first peak of radiation. Consequently, the 172㎚ radiation becomes strong as the duty ratio increases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.169-172
• /
• 1999

In this experimental study we Proposed the double dielectric barrier discharge (DDBD) reactor to produce as high an electric field as possible. The experiment are conducted for applied voltage from 15 to 20[tV], flow gas rage at 2[1/min] and pulse rate at 120[pulses/s] and 240[pulses/s]. SPD connection of DDBD which combine the surface discharge with the silence discharge was most effective to reduce the NOx. In the decomposition efficiency per watt, the low pulse rate gave hotter efficiency than that of the high pulse rate. However in DeNOx rate, the high pulse rate gave better performance than that of the low pulse rate. NOx removal rate increased with increasing the applied voltage in all reactors.