• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.11-11
• /
• 2000

이동통신기술의 급격한 발달로 고주파회로의 packaging과 interconnect 기술의 고성능화 와 저가격화에 대한 새로운 도전이 요구되고 있다‘ 대부분 기존의 무선통신 부품은 P PCB(Printed Wiring Board)기술을 활용하고 있으나 이러한 기술이 점차로 고주파화되는 경 향을 만족시킬수 없어 새로운 고주파 부품기술이 요구되고 있는 실정이다 .. RF 회로를 구성 하기 위하여 PCB소재의 환경적, 치수안정성 문제를 극복하기 위하여 L TCC(Low T Temperature Cofired Ceramics)기술이 최근 주목을 받고 있다. 차세대 이동통신 기술은 수십 GHz 이상의 고주파특성이 우수하고, 고성능의 초소형의 부품을 저가격으로 제조할수 있으며, 시장의 변화에 기민하게 대처할수 있는 기술이 요구되 고 있으며, 이러한 기술적 필요성에 부합할수 있도록 LTCC 기술이 제안되었다. 이러한 C Ceramic Interconnect 기술은 높은 신뢰성을 바탕으로 fine patterning 기술과 저가의 m metallizing 기술로 가능하게 되었다. 초고주파 통신부품기술은 미국과 유럽 등을 중심으로 G GHz 대역또는 mm wave 대역의 기술에 대하여 치열한 기술개발 경쟁을 벌이고 있으며, 이 러한 고주파 패키징 기술을 바탕으로 미래의 군사, 항공, 우주 및 이동통신 기술에 지대한 영향을 미칠수 있는 기반기술로 자리잡을 전망이다. L LTCC 기술은 기존의 후막혼성기술에 비하여 공정이 단순하고 대량생산이 가능하고 가 격이 비교적 저렴하다. 또한 다층구조로 제작할수 있고, 수동소자를 내장할수 있어 회로의 소형화와 고밀도화가 가능하다. 특히 무선으로 초고속 정보를 처리하기 위하여 이동통신기 기의 고주파화가 빠르게 진행됨에 따라서 고분자재료에 비하여 고주파특성이 우수할뿐아니 라 환경적, 치수안정성이 우수한 세라믹소재플 사용함으로써 고주파 손실율을 저감할 수 있 다 .. LTCC 기술은 후막회로 기술과 tape dielectric 기술이 결합된 기술이다. 표준화된 소재 와 공정기술을 활용하여 저가격으로 고성능소자플 제작할 수 있으며, 전극재료로서 높은 전 도도를 갖고 있는 Ag, Cu, Au 및 Pd! Ag릎 사용함으로써 고주파 손실을 저감시킬 수 있다. L LTCC 기술이 최종적으로 소형화, 고기능 고주파 부품기술로 지속적으로 발전하기 위하여 무수축(Zero shrinkage) 소성기술, 광식각 후막기술 등이 원천기술로서 확립될 수 있어야 하 며, 특히 국내의 이동통신 기술에 대한 막대한 투자에도 불구하고 차세대 이동통신 부품기 술에 대한 개발은 상대적으로 미흡한 실정이므로 국내에 LTCC 관련 소재공정 및 부품소자 기술에 대한 개발투자가 시급히 이루워져야 할 것으로 판단된다. 본 발표에서는 지금까지 국내외 LTCC 기술의 발전과정을 정리하였고, 현재 이 기술의 응용과 소재와 공정을 중심으로한 개발현황에 대하여 조사하였으며, 앞으로 LTCC가 발전 해야할 방향을 제시하고자 한다.

• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.67-75
• /
• 2005

For th aim of lightweight microwave absorbers, conductive and magnetic microspheres are fabricated by plating of Co films on hollow ceramic microspheres of low density. Metal plating was carried out in a two-step electroless plating process (pre-treatment of activation and plating). Uniform coating of the film with about $2{\~}3{\cal}um$ thickness was identified by SEM. High-frequency magnetic and microwave absorbing properties were determined in the rubber composites containing the Co-coated microspheres. Due to conductive and ferromagnetic behavior of the Co thin films, high dielectric constant and magnetic loss can be obtained in the microwave frequencies. Due to those electromagnetic properties, high absorption rate (25 dB) and thin matching thickness ($2.0{\~}2.5{\cal}mm$) are predicted in the composite layers containing the metal-coated microspheres of low density (about 0.84 g/cc) for the electromagnetic radiation in microwave frequencies.

• Journal of the Korean Magnetics Society
• /
• v.19 no.6
• /
• pp.203-208
• /
• 2009

Magnetic and Ka-band absorbing properties have been investigated in Ti-Co substituted M-type barium hexaferrites with $BaTi_{0.5}Co_{0.5}Fe_{11}O_{19}$ composition. The ferrite powders were prepared by conventional ceramic processing technique and used as absorbent fillers in ferrite-rubber composites. The magnetic properties were measured by vibrating sample magnetometer. The complex permeability and dielectric constant were measured by using the WR-28 rectangular waveguide and network analyzer in the frequency range 26.5~40 GHz. For the Ti-Co substituted M-hexaferrites, the ferromagnetic resonance is observed at Ka-band (29.4 GHz). The matching frequency and matching thickness are determined by using the solution map of impedance matching. A wide band microwave absorbance is predicted with controlled ferrite volume fraction and absorber thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.57-58
• /
• 2008

PTC thermistor are characterized by an increase in the electrical resistance with temperature. The PTC materials of middle Curie point were produced or that of high Curie point (above $200^{\circ}C$), it was determined that compositional modifications of $Pb^{2+}$ for $Ba^{2+}$ produce change sin the Curie point to higher temperature. PTC ceramic materials with the Curie point above $120^{\circ}C$ were prepared by adding $PbTiO_3$, PbO or $Pb_3O_4$ into $BaTiO_3$. Thereby, adding $Pb^{2+}$ into $BaTiO_3$-based PTC material to improve Tc was studied broadly, however, weal know that PbO was poisonous and prone to volatilize, then to pollute the circumstance and hurt to people, so we should dope other innocuous additives instead of lead to increase Tc of composite PTC material. In order to prepare lead-free $BaTiO_3$-based PTC with middle Curie point, the incorporation on $Bi_{1/2}Na_{1/2}TiO_3$ into $BaTiO_3$-based ceramics was investigated on samples containing 0, 1, 2, 3, 4, and 50mol% of $Bi_{1/2}Na_{1/2}TiO_3$. $Bi_{1/2}Na_{1/2}TiO_3$ was compounded as standby material by conventional solid-state reaction technique. The starting materials were $Bi_{1/2}Na_{1/2}TiO_3$, $BaCO_3$, $TiO_2$ and $Y_2O_3$ powder, and using solid-state reaction method, too. The microstructures of samples were investigated by SEM, DSC, XRD and dielectric properties. Phase composition and lattice parameters were investigated by X-ray diffraction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.363-364
• /
• 2005

LTCC(low temperature co-fired ceramics)용 glass/ceramic 복합체를 제조하기 위해 3종류 의 glass를 선정하고 filler로 $Al_2O_3$ 와 $TiO_2$를 사용하여 glass frit에 따른 소결 및 유전 특성에 대하여 조사하였다. Glass frit은 lead-borosilicate(PBS), zinc-borosilicate(ZBS), bismuth-borosilicate(BBS) glass 조성을 사용하였고 1100~$1400^{\circ}C$에서 melting시킨 후 quenching하여 frit화하였다. $Al_2O_3$와 $TiO_2$ filler에 10~50 vol%로 glass frit을 각각 혼합한 후 600~$950^{\circ}C$에서 2시간 동안 소결한 결과 50 vol% glass frit 일 때 $900^{\circ}C$ 이하에서 소성이 가능하였다. 유전특성은 $900^{\circ}C$에서 $Al_2O_3$-50vol%PBS($\varepsilon_{r}$=8.8, $Q{\times}f_o$=4,900, $\tau_f$=-24), $Al_2O_3$-50vol% ZBS($\varepsilon_{r}$=5.7, $Q{\times}f_o$=17,800, $\tau_f$=-21), $Al_2O_3$-50vol%BBS($\varepsilon_{r}$=11.1, $Q{\times}f_o$= 2,080, $\tau_f$=-48), $TiO_2$-50vol%PBS($\varepsilon_{r}$=18.6, $Q{\times}f_o$=3,800, $\tau_f$=+135), $TiO_2$-50vol%ZBS($\varepsilon_{r}$=36.4, $Q{\times}f_o$= 7,500, $\tau_f$=+159), $TiO_2$-50vol%BBS($\varepsilon_{r}$=56.4, $Q{\times}f_o$=520, $\tau_f$=+119)을 나타내었다. 따라서 LTCC용 기판재료 및 마이크로파 유전체로 응용이 가능한 것으로 확인되었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.695-700
• /
• 2018

This paper presents the development of compact and lightweight broadband power amplifier module using HMIC (Hybrid Microwave Integrated Circuit) technology that could be high-density integration for many non-packaged microwave components into the small area of a high dielectric constant printed circuit board, such as a ceramic substrate, also using the special design and fabrication schemes for the structure of minimized electromagnetic interference to obtain the homogeneous electrical performance at the wideband frequency. The results confirmed that the small signal gain has a gain flatness of ${\pm}1.5dB$ within the range of 32 to 36 dB. In addition, the output power satisfied more than 30 dBm. The noise figure was measured within 7 dB, and OIP3 (Output Third Order Intercept Point) was more than 39 dBm. The fabricated broadband power amplifier satisfied the target specification required to electrically drive the high power amplifiers of jamming generators for electronic warfare, so the actual applicability to the system was verified. Future studies will be aimed at designing other similar microwave power amplifiers in the future.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.97-105
• /
• 2020

Recently, as the data speed and operating frequencies of Ethernet keeps increasing, electro magnetic interference (EMI) also becomes increasing. The generation of such EMI will cause malfunction of near electronic devices. In this study, EMI filters were applied to reduce the EMI generated by DC-DC SMPS (switching mode power supply), which is the main cause of EMI generation of Ethernet switch. As the EMI filter, MLCCs with excellent withstanding voltage characteristics were used, which had advantages in miniaturization and mass production. Two types of EMI MLCC filters were used, which are X-capacitor and X, Y-capacitor. X-capacitor was composed of 2 MLCCs with 10 nF and 100 nF capacity and 1 Mylar capacitor. Y-capacitor was consisted of 6 MLCCs with a capacity of 27 nF. When only X-capacitor was applied as EMI filter, the conductive EMI field strength exceeded the allowable limit in frequency range of 150 kHz ~ 30 MHz. The radiative EMI also showed high EMI strength and very small allowable margin at the specific frequencies. When the X and Y-capacitors were applied, the conductive EMI was greatly reduced, and the radiation EMI was also found to have sufficient margin. In addition, X, Y-capacitors showed very high insulation resistance and withstanding resistance performances. In conclusion, EMI X, Y-capacitors using MLCCs reduced the EMI noise effectively and showed excellent electrical reliability.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.3
• /
• pp.297-303
• /
• 2024

In this study, KTN heterolayer thin films were fabricated by alternately stacking films of K(Ta_0.70Nb_0.30)O₃ and K(Ta_0.55Nb_0.45)O₃ synthesized using the sol-gel method. The sintering temperature and time were 750℃ and 1 hour, respectively. All specimens exhibited a polycrystalline pseudo-cubic crystal structure, with a lattice constant of approximately 0.398 nm. The average grain size was around 130~150 nm, indicating relatively uniform sizes regardless of the number of coatings. The average thickness of a single-coated film was approximately 70 nm. The phase transition temperature of the KTN heterolayer films was found to be approximately 8~12℃. Moreover, the 6-coated KTN heterolayer film displayed an excellent dielectric constant of about 11,000. As the number of coatings increased, and consequently the film thickness, the remanent polarization increased, while the coercive field decreased. The 6-coated KTN heterolayer film exhibited a remanent polarization and coercive field of 11.4 μC/cm² and 69.3 kV/cm at room temperature, respectively. ΔT showed the highest value at a temperature slightly above the Curie temperature, and for the 6-coated KTN heterolayer film, the ΔT and ΔT/ΔE were approximately 1.93 K and 0.128×10^-6 K·m/V around 40℃, respectively.

• Korean Journal of Materials Research
• /
• v.34 no.2
• /
• pp.116-124
• /
• 2024

In this study, we investigated the microstructure and piezoelectric properties of 0.96(K_0.456Na_0.536)Nb_0.95Sb_0.05-0.04Bi_0.5(Na_0.82K_0.18)_0.5ZrO₃ (KNNS-BNKZ) ceramics based on one-step and two-step sintering processes. One-step sintering led to significant abnormal grain (AG) growth at temperatures above 1,085 ℃. With increasing sintering temperature, piezoelectric and dielectric properties were enhanced, resulting in a high d₃₃ = 506 pC/N for one-step specimen sintered at 1,100 ℃ (one-step 1,100 ℃ specimen). However, for one-step 1,115 ℃ specimen, a slight decrease in d₃₃ was observed, emphasizing the importance of a high tetragonal (T) phase fraction for superior piezoelectric properties. Achieving a relative density above 84 % for samples sintered by the one-step sintering process was challenging. Conversely, two-step sintering significantly improved the relative density of KNNS-BNKZ ceramics up to 96 %, attributed to the control of AG nucleation in the first step and grain growth rate control in the second step. The quantity of AG nucleation was affected by the duration of the first step, determining the final microstructure. Despite having a lower T phase fraction than that of the one-step 1,100 ℃ specimen, the two-step specimen exhibited higher piezoelectric coefficients (d₃₃ = 574 pC/N and k_p = 0.5) than those of the one-step 1,100 ℃ specimen due to its higher relative density. Performance evaluation of magnetoelectric composite devices composed of one-step and two-step specimens showed that despite having a higher g₃₃, the magnetoelectric composite with the one-step 1,100 ℃ specimen exhibited the lowest magnetoelectric voltage coefficient, due to its lowest k_p. This study highlights the essential role of phase fraction and relative density in enhancing the performance of piezoelectric materials and devices, showcasing the effectiveness of the two-step sintering process for controlling the microstructure of ceramic materials containing volatile elements.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.2
• /
• pp.83-90
• /
• 2023

The β-Ga₂O₃ has the most thermodynamically stable phase, a wide band gap of 4.8~4.9 eV and a high dielectric breakdown voltage of 8MV/cm. Due to such excellent electrical characteristics, this material as a power device material has been attracted much attention. Furthermore, the β-Ga₂O₃ has easy liquid phase growth method unlike materials such as SiC and GaN. However, since the grown pure β-Ga₂O₃ single crystal requires the intentionally controlled doping due to a low conductivity to be applied to a power device, the research on doping in β-Ga₂O₃ single crystal is definitely important. In this study, various source powders of un-doped, Sn 0.05 mol%, Sn 0.1 mol%, Sn 1.5 mol%, Sn 2 mol%, Sn 3 mol%-doped Ga₂O₃ were prepared by adding different mole ratios of SnO₂ powder to Ga₂O₃ powder, and β-Ga₂O₃ single crystals were grown by using an edge-defined Film-fed Growth (EFG) method. The crystal direction, crystal quality, optical, and electrical properties of the grown β-Ga₂O₃ single crystal were analyzed according to the Sn dopant content, and the property variation of β-Ga₂O₃ single crystal according to the Sn doping were extensively investigated.