• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.153-153
• /
• 2012

Endpoint detection with plasma impedance monitoring and self-plasma optical emission spectroscopy is demonstrated for dielectric layers etching processes. For in-situ detecting endpoint, optical-emission spectroscopy (OES) is used for in-situ endpoint detection for plasma etching. However, the sensitivity of OES is decreased if polymer is deposited on viewport or the proportion of exposed area on the wafer is too small. To overcome these problems, the endpoint was determined by impedance signal variation from I-V monitoring (VI probe) and self-plasma optical emission spectroscopy. In addition, modified principal component analysis was applied to enhance sensitivity for small area etching. As a result, the sensitivity of this method is increased about twice better than that of OES. From plasma impedance monitoring and self-plasma optical emission spectroscopy, properties of plasma and chamber are analyzed, and real-time endpoint detection is achieved.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.5
• /
• pp.231-237
• /
• 2001

Etch rates up to 120 nm/min for $Ta_{2}O_{5}$ were achieved in both $SF_{6}/Ar$ and $Cl_{2}/Ar$ discharges. The effect of ultraviolet (UV) light illumination during ICP etching on $Ta_{2}O_{5}$ etch rate in those plasma chemistries was examined and UV illumination was found to produce significant enhancements in $Ta_{2}O_{5}$ etch rates most likely due to photoassisted desorption of the etch products. The effects of ion flux, ion energy, and plasma composition on (Ba, Sr)$TiO_3$ etch rate were examined and maximum etch rate ~90 nm/min was achieved in $Cl_{2}/Ar$ ICP discharges while $CH_{4}/H_{2}/Ar$ chemistry produced extremely low etch rates (${\leq}10\;nm/min$) under all conditions.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.783-786
• /
• 2003

A simple fabrication method of self-aligned ridge waveguides with dielectric side buffers is demonstrated on +Z- cut LiNbO$_3$. The ridge waveguide is fabricated by a combination of the annealed proton exchange process and the proton-exchanged wet etching technique. The self-aligned process is achieved by wet etching of aluminum.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.3
• /
• pp.165-178
• /
• 2024

In semiconductor memory device manufacturing, the capability for high aspect ratio contact (HARC) etching determines the density of memory device. Given that there is no standardized definition of "high" in high aspect ratio, it is crucial to continuously monitor recent technology trends to address technological gaps. Not only semiconductor memory manufacturing companies such as Samsung Electronics, SK Hynix, and Micron but also semiconductor manufacturing equipment companies such as Lam Research, Applied Materials, Tokyo Electron, and SEMES release annual reports on HARC etching technology. Although there is a gap in technological focus between semiconductor mass production environments and various research institutes, the results from these institutes significantly contribute by demonstrating fundamental mechanisms with empirical evidence, often in collaboration with industry researchers. This paper reviews recent studies on HARC etching and the study of dielectric etching in various technologies.

• Corrosion Science and Technology
• /
• v.10 no.1
• /
• pp.37-42
• /
• 2011

Aluminum was electrochemically etched in acid solution and the surface area was magnified by the formation of etch pits. Etched aluminum was covered with a compact and dense dielectric oxide film by anodization and applied to the aluminum electrolytic capacitor electrode. Capacitance of aluminum electrolytic capacitor is closely related with surface area, which depends on size and number of etch pits. Size of etch pits need to be controlled because inside of the pits can be buried by the formation of dielectric oxide film. In this work, the effect of ultrasound pretreatment on the aluminum etch pit formation and capacitance were investigated. Additionally, the relationship between the second etching effect on pit size and capacitance was studied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.123.2-123.2
• /
• 2013

Etching endpoint detection with plasma impedance monitoring (PIM) is demonstrated for small area dielectric layers inductive coupled plasma etching. The endpoint is determined by the impedance harmonic signals variation from the I-V monitoring system. Measuring plasma impedance has been examined as a relatively simple method of detecting variations in plasma and surface conditions without contamination at low cost. Cluster analysis algorithm is modified and applied to real-time endpoint detection for sensitivity enhancement in this work. For verification, the detected endpoint by PIM and real-time cluster analysis is compared with widely used optical emission spectroscopy (OES) signals. The proposed technique shows clear improvement of sensitivity with significant noise reduction when it is compared with OES signals. This technique is expected to be applied to various plasma monitoring applications including fault detections as well as end point detection.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.14-17
• /
• 2000

Giga bit dynamic random access memory(DRAM) requires the capacitor of high dielectric films. Some metal oxides films have been proposed as the dielectric material . And Pt is one of the most promising electrode materials. However very little has been done in developing the etching technologoy Pt film. Therefore, it is the first priority to develop the technology for plasma etching of Pt film. In this study, the dry etching of Pt film was investigated in Inductively Coupled Plasma(ICP) etching system with Cl$_2$/Ar and HBr/Cl$_2$/Ar gas mixing. X-ray photoelectron spectroscopy (XPS) was used in analysis of sidewall residues for the understanding of etching mechanism. We found the etch residues on the pattern sidewall is mainly Pt-Pt, Pt-Cl and Pt-Br compounds, Etch profile was observed by Scanning Electron Spectroscopy(SEM) . The etch rate of Pt film at 10%, Cl$_2$/90% Ar gas mixing ration was higher than at 100%. Ar. Addition of HBr to Cl$_2$/Ar as an etching gas led to generally higher selectivity to SiO$_2$. And the etch residues were reduced at 5% HBr/5% Cl$_2$/90% Ar gas mixing ration. These pages provide you with an examples of the layout and style which we wish you to adopt during the preparation of your paper, Make the width of abstract to be 14cm.

• Journal of Korean Vacuum Science & Technology
• /
• v.5 no.2
• /
• pp.52-55
• /
• 2001

We report best dielectric function of ZnS by spectroscopic ellipsometry in the 3.7 - 6.0 eV photon energy range at room temperature. Using proper wet chemical etching procedure, natural overlayer was removed to obtain the pure dielectric function of ZnS, which had a higher <$\xi$$_2$> value at the El band gap peak than that previously reported. We also determined the dielectric property of the natural overlayer on ZnS by following the evolution of <$\xi$$_2$> with chemical etching. We found that the optical property of the overlayer was well described by amorphous semiconductor model.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.170-170
• /
• 2013

We present a novel etching technique for 2-dimentional (2-D) hexagonal boron nitride (h-BN) by using capacitively coupled plasma (CCP) of oxygen combined with a post-treatment by de-ionized (DI) water. Oxygen CCP etching process for h-BN has been systematically studied. It is found that a passivation layer was generated to obstruct further etching while it can be easily and radically removed by DI water. An essential cleaning effect also has been observed in the etching process, organic residues are successfully removed and the surface roughness has much decreased. Considering h-BN is the most important 2-D dielectric material and its potential application for graphene to silicon-based electronic devices, such an etching method can be widely used to control the 2-D h-BN thickness and improve the surface quality.

• Korean Journal of Materials Research
• /
• v.16 no.3
• /
• pp.151-156
• /
• 2006

A method for fabrication of nano-scale GaN structure by inductively coupled plasma etching is proposed, exploiting a thermal dewetting of Pt thin film as an etch mask. The nano-scale Pt metal islands were formed by the dewetting of 2-dimensional film on $SiO_2$ dielectric materials during rapid thermal annealing process. For the case of 30 nm thick Pt films, pattern formation and dewetting was initiated at temperatures greater $600^{\circ}C$. Controlling the annealing temperature and time as well as the thickness of the Pt metal film affected the size and density of Pt islands. The activation energy for the formation of Pt metal island was calculated to be 23.2 KJ/mole. The islands show good resistance to dry etching by a $CF_4$ based plasma for dielectric etching indicating that the metal islands produced by dewetting are suitable for use as an etch mask in the fabrication of nano-scale structures.