• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.234-237
• /
• 2008

It was reported that the semi-solid forming process has many advantages over the conventional forming process, such as a long die life, good mechanical properties and energy savings. It is very important, however, to control liquid segregation to gain mechanical property improvement of materials. During forming process, Rheology material has complex characteristics, thixotropic behavior. Also, difference of velocity between solid and liquid in the semi-solid state material makes a liquid segregation and specific stress variation. Therefore, it is difficult for a numerical simulation of the rheology Process to be Performed. General Plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. The behavior and stress of solid particle in the rheology material during forging process is affected by viscosity, temperature and solid fraction. In this study, compression experiments of aluminum alloy were performed under each other tool shape. In addition, the dynamics behavior compare with Okano equation to Power law model which is viscosity equation.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2253-2261
• /
• 2002

Recently the hydroforming technology has drawn a lot of attention because of its capability to produce high quality and light weight parts. In the present study, the tube expansion - one of the simplest hydroforming processes, has been investigated in order to understand fundamental phenomena such as deformation characteristics and effect of process parameters. As a result, the most important process parameters, which determine the state of stress at the expanded zone, were found to be pressure and die displacement. If the stress becomes equi-axial tension at the zone, necking occurs at some distance from the weld line and develops into a crack along the axial direction. Some aspects of mechanical property measurements as well as distributions of hardness and microstructure are also discussed in this paper.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.99-105
• /
• 2010

This study was performed to solve the breaking problem in the fine blanking(FB) process of sector gears for car seat recliner using nickel chrome molybdenum steel(SNCM220) plate. The optimal design of embossing circle is changed to oval with labors' experiences and finite element analysis. The maximum principal stress and effective strain in a forming process are analyzed by commercial finite element software to solve the problems in embossing stage of FB process. As a result of FE analysis, the maximum principal stress in forming is lower than yield point of material. It is shown from experiments in the modified die that the formed gear does not break in embossing stage.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.1-10
• /
• 2020

The seal plays a role in preventing oil leakage when the lip and the rotating shaft come into contact with the fluid and air pressure. Recently, micro dimples or micro pockets are processed and used on the lubrication surfaces of thrust bearings, mechanical bearings, and piston rings. Compared to a smooth surface, micro dimples reduce friction and increase the life of parts. This paper analyzed various kinds of micro dimple shapes on the sealing surface, i.e. circle, rectangle, triangle, and trapezoid. For this purpose, Introduced the design of experiments to work out a micro dimple configuration, unlikely to be damaged from cracks and low in contact stress. As a result, the triangular dimple showed the best results. Optimal factors were dimple size 0.15 mm, dimple depth 0.0383 mm, dimple density 40%, and the maximum equivalent stress was 9.1455 MPa, and the maximum contact pressure was 9.6612 MPa. This paper analyzed the optimal shape of dimples by finite element analysis. As a research project, experiments and comparative analysis of micro dimple shapes are needed.

• 소성∙가공
• /
• 제15권3호
• /
• pp.232-240
• /
• 2006

Magnesium alloys are expected to be widely used fur the parts of structural and electronic appliances due to their lightweight and EMI shielding characteristics. While the die casting has been mainly used to manufacture the parts from the magnesium alloys, the press forming is considered as an alternative to the die casting for saving the manufacturing cost and improving the structural strength of the magnesium alloy parts. However, the magnesium alloy has low formability at room temperature and therefore, in many cases, forming at elevated temperatures is necessary to obtain the required material flow without failure. In the present study, square cup deep drawing tests using the magnesium alloy AZ31 sheet were experimentally conducted at various elevated temperatures as well as room temperature, and the corresponding finite-element simulations, which calculated the damage evolution based on the Oyane's criterion, were conducted using the stress-strain relations from the tensile tests at various temperatures. The formability predictability by the finite-element analysis was investigated by comparing the predicted damage distributions over the deformed AZ31 sheet at elevated temperatures with the corresponding experimental deformations with failures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.122-125
• /
• 2005

Magnesium alloys are expected to be widely used for the parts of structural and electronic applications due to their lightweight and EMI shielding characteristics. While the die casting has been mainly used to manufacture the parts from the magnesium alloys, the press forming is considered as an alternative to the die casting for saving the manufacturing cost and improving the structural strength of the magnesium alloy parts. However, the magnesium alloy has low formability at room temperature and therefore, in many cases, forming at elevated temperatures is necessary to obtain the required material flow without failure. In the present study, square cup deep drawing tests using the magnesium alloy AZ31 sheet were experimentally conducted at various elevated temperatures as well as room temperature, and the corresponding finite-element simulations, which calculated the damage evolution based on the Oyane's criterion, were conducted using the stress-strain relations from the tensile tests at various temperatures. The formability predictability by the finite-element analysis was investigated by comparing the predicted damage distributions over the deformed AZ31 sheet at elevated temperatures with the corresponding experimental deformations with failures.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.44-50
• /
• 2006

The mono steel forged piston was improved a mechanical strength of an aluminum piston and reduced the weight of a articulated piston. The mono steel forged piston was composed of forged crown part and forged skirt part and was completed by friction welding process of two forged parts. Forging process analysis and friction welding analysis was done by finite element simulation using numerical package DEFORM. The preform shape and the initial billet dimension were decided by maximum stress of the die, amount of the flash and filling of die. The upset length of friction welding variable was decided by the shape of the flash that was created by friction welding analysis. Through this research, we developed a forging process of the mono steel forged piston, and decided the design variables of friction welding.

• Design & Manufacturing
• /
• 제9권3호
• /
• pp.19-23
• /
• 2015

Non-pneumatic wheels have been widely used instead of general tube type wheels beause of many reasons, for example, wheel size, price restriction, heavy-duty problem and so on. Almost small size wheels or casters were non-pneumatic type but structural stability was not certified. This paper presents a double structured non-pneumatic wheel, called "smart caster", which consisted with inner and outer wheels connected by chips, and finite element analysis processes were conducted in order to determine important dwsign factors before actual design for mass production. For structural analysis ABAQUS was used under various boundary conditions with incrementally varied loads until 2,000N. Then structural staility was evaluated according to varied loads below ultimate stress. Generally stresses were concentrated at the lower parts of the wheel, and especially contact parts between wheel and ground. In addition, maximum stress appeared at contact parts between the wheel lower part and chips.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.53-56
• /
• 1997

The multistage precision forming process for aperture of electronic guns consists mainly of drawing and swaging operations. The multistage forming sequence is analyzed in view of production industry, and based on the industrial investigation. The processes are simulated by the finite element code MARC. The elastic recovery, strain and stress distribution, and the die forces are summarized.

• 소성∙가공
• /
• 제18권1호
• /
• pp.20-25
• /
• 2009

A finite element analysis was carried out for a 4:1 planar contraction die for polymer melts using the viscoelastic constitutive equation of Leonov. Viscoelastic fluids showed significant differences in pressure drop and birefringence in contraction and expansion flows. The pressure drop was higher and the birefringence smaller in expansion than in contraction flow. The difference increased with increasing flow rate. The nonlinear Leonov model was shown to describe the viscoelastic effects observed in experiments.