• Journal of Surface Science and Engineering
• /
• v.29 no.5
• /
• pp.549-555
• /
• 1996

Diamond Like Carbon film is amorphous film which is considered to consist of three coordinate graphite structure and tetrahedron coordinate diamond structure. Its hardness, thermal conductivity and chemical stability are nearly to one of diamond. It is well known to become semi-conductor by doping of inpurity. In this study Diamond Like Carbon film was synthesized by Microwave Plasma CVD in the gas mixture of hydrogen-methan-nitrogen and doped of nitrogen on the single-crystal silicon or silica glass. The temperature of substrate and nitrogen concentration in the gas mixture had an effect on the bonding state, structural properties and conduction mechanism. The surface morphology was observed by Scanning Electron Microscope. The strucure was analyzed by laser Raman spectrometry. The bonding state was evaluated by electron spectroscopy. Diamond Like Carbon film synthesized was amorphous carbon containing the $sp^2$ and $sp^3$ carbon cluster. The number of $sp^2$ bonding increased as nitrogen concentration increased from 0 to 40 vol% in the feed gas at 1233K substrate temperature and at $7.4\times10^3$ Pa. Increase of nitrogen concentration made Diamond Like Carbon to be amorphous and the doze of nitragen could be controlled by nitrogen concentration of feed gas.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.1
• /
• pp.84-95
• /
• 2001

Titanium is widely used in dentistry for its low density, high strength, fatigue resistance, corrosion resistance, and biocompatibility. But it has a tendency of surface damage under circumstance of friction and impact for its low hardness of the surface. Coating is one of methods fir increasing surface hardness. Its effect is to improve surface physical characteristics without change of titanium. Diamond-like carbon and titanium nitride are known for its high hardness of the surface. So that this study was aimed at the wear test and the cytotoxicity test of the commercially pure titanium and Ti-6Al-4V alloy which were deposited by diamond-like carbon film or titanium nitride film to acertain improvement of the surface hardness and the biocompatibility. A disk (25mm diameter, 2mm thickness) was made of commercially pure titanium and Ti-6Al-4V alloy and these substrates were deposited by diamond-like carbon film or titanium nitride film. Diamond-like carbon film was deposited by the method of radiofrequency plasma assisted chemical vapor deposition and titanium nitride film was deposited by the method of reactive arc ion plating. Then these substrates were tested about wear characteristics by the pin-on-disk type wear tester in which ruby ball was used as a wear causer under the load of 32N, The fracture cycles were measured by rotating the substrates until their films were fractured. The wear volume was measured after 150 cycles and 3,000 cycles using surface profiler. The cytotoxicity test was peformed by the method of the MTT assay. The results were as follows : 1. In the results of the wear volume test, commercially pure titanium and titanium alloy which were coated by diamond-like carbon film or titanium nitride aim had higher resistance against wear than the substrates which were not coated by any films (P<0.05). 2. In the results of the fracture cycle test and the wear volume test, diamond-like carbon film had higher resistance against wear than titanium nitride film (P<0.05). 3. In both coatings of diamond-like carbon aim and titanium nitride film, Ti-6Al-4V alloy had higher resistance against wear than commercially pure titanium (P<0.05) 4. In the results of the cytotoxicity test, diamond-like carbon film and titanium nitride film had little cytotoxicity as like commercially pure titanium or Ti-6Al-4V alloy (P>0.05).

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.243-245
• /
• 1994

We synthesized the conducting diamond-like carbon films using plasma-enhanced chemical vapor deposition and analysized its characteristics. We obtained the metal-containing diamond-like carbon films using $CH_4$, Ar gas and aluminum target. We observed the changes of electrical conductivity, microhardness and surface morphology according to $Ar/CH_4$ ratio, substrate bias and target bias. As the target bias and $Ar/CH_4$ ratio increase and the substrate bias decreases, the electrical conductivity and surface roughness increase. The increase of hardness involves decrease of the electrical conductivity. Metal-containing amorphous hydrogenated carbon films show improved adhesion on metal substrates compared to pure diamond-like carbon films and better electrical conductivity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.5
• /
• pp.77-83
• /
• 2022

A high-hardness tool material is required to reduce extreme abrasive wear when drilling carbon fiber reinforced plastic (CFRP). Single-crystal diamond is the hardest material in the world, but it is very expensive to be used as a cutting tool. Polycrystalline diamond (PCD) is a diamond grit fused at a high temperature and pressure, and diamond-like carbon (DLC) is an amorphous carbon with high hardness. This study compares DLC coatings and PCD inserts to conventional TiAlN-coated tungsten carbide drills. In fiberglass and carbon fiber reinforced polymer drilling, the tool wear of DLC-coated carbide was approximately half that of TiAlN-coated tools, and slight tool wear occurred in the case of PCD insert end drills.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.214-218
• /
• 2003

We studied the nematic liquid crystal (NLC) aligning capabilities by the UV alignment method on a diamond like carbon (DLC) thin film surface A good LC alignment by UV exposure on the DLC thin film surface at 200${\AA}$ of layer thickness was achieved. Also, a good LC alignment by the UV alignment method on the DLC thin film surface was observed at annealing temperature of 180$^{\circ}C$. However, the alignment defect of the NLC was observed above annealing temperature of 200$^{\circ}C$. Consequently, the good thermal stability of LC alignment by the UV alignment method o the DLC thin film surface can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.419-422
• /
• 2002

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of a diamond like carbon (DLC) thin film. A high pretilt angle of about $3.5^{\circ}$ by ion beam(IB) exposure on the DLC thin film surface was measured. A good LC alignment by the IB alignment method on the DLC thin film surface was observed at annealing temperature of $200^{\circ}C$, and the alignment defect of the NLC was observed above annealing temperature of $220^{\circ}C$. Consequently, the high NLC pretilt angle and the good thermal stability of LC alignment by the IB alignment method on the DLC thin film surface can be achieved.

• Journal of Surface Science and Engineering
• /
• v.35 no.2
• /
• pp.122-128
• /
• 2002

This study was conducted to synthesize the diamond like carbon films by plasma enhanced chemical vapor deposition (PECVD). The effects of gas composition on growth and mechanical properties of the films were investigated. A little amount of hydrogen or oxygen were added to base gas mixture of methane and argon. Methane dissociation and diamond like carbon nucleation were enhanced by installing negatively bias grid near substrate. The deposited films were indentified as hard diamond like carbon films by micro-Raman spectroscopy. The surface and fractured cross section of the films which were observed by scanning electron microscopy showed that film growth is very slow as about 0.3$\mu\textrm{m}$/hour, and relatively uniform with hydrogen addition. Vickers hardness of tungsten carbide (WC) cutting tool increased from about 1000 to 1600~1800 by deposition of DLC film, that of commercial TiN coated tool was about 1270. In cutting test of aluminum 6061 alloy, DLC coated cutting tool showed 1/3 or lower crater and flank wear than TiN coated or non-coated WC cutting tools.

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.248-254
• /
• 1998

DLC(Diamond-Like-Carbon) thin film, one of the solid state amorphous carbon films, has been deposited by the method of PECVD (Plasma Enhanced Chemical Vapor Deposition). The structural features have been characterized using both FT-IR Spectroscopy and Raman Scattering. The film is considered to consist of microcrystalline diamond domains and graphitelike carbon domains, which are interconnected by hydrogenated $sp^3$ tetrahedral carbons. This shows a good agreement with the results by I-Vmeasurements. In I-Vstudy, the sudden increase of current has been observed and this phenomenon is understood to be due to the tunneling effect between graphitelike domains. A characteristic feature related to the $\beta$-SiC has been identified in the study of Raman Scattering for the very thin film, which suggests that a buffer layer forms at the interface of the Si substrate and the carbon film.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.184.2-184
• /
• 2000

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.9-15
• /
• 2020

Carbon fiber reinforced plastic (CFRP) is a composite material useful in the aerospace and automotive industries because of its light weight and high strength. In this study, side milling tests were carried out using AlCrN, diamond-like carbon (DLC), and diamond-coated end mills. Additionally, a comparison study according to the cobalt content was conducted. Thus, tool wear and surface quality were examined and the influences of using coating and a certain material type were analyzed. The surface roughness of the machined surface was measured. Microscope observations revealed that the CFRP fiber at the machined surface was not damaged even at a cutting distance of 3,000 mm. Therefore, this study showed that the diamond-coated end mill containing 6% cobalt is appropriate for milling CFRP.