• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1307-1308
• /
• 2006

The purpose of this study was to examine the interfacial reaction between diamond grits and Ni-based, Ag-based, brazing filler metal, respectively. The morphology of the interface between diamond grits and Ni-based, filler metal exhibited a very good condition after this heat treatment. Cr-carbide and Ni-rich compounds were detected by XRD analysis in the vicinity of the interface between diamond grits and Ni-based, filler metal after vacuum induction brazing. Chromium carbide is considered to play an important role in the high bonding strength achieved between diamonds grits and the brazing alloy.

• 한국분말재료학회지
• /
• 제14권6호
• /
• pp.348-353
• /
• 2007

In the present study, Zr-base metallic glass (MG) and Zr-base BMG/diamond composites were fabricated using a combination of gas atomization and spark plasma sintering (SPS). The microstructure, thermal stability and mechanical property of both the specimens as atomized and sintered were investigated. The experimental results showed that the SPSed specimens could be densified into nearly 100% and maintained the initial thermal stability at the sintering temperature of 630K. In addition, MG/diamond powder composites were successfully synthesised using SPS process. The composites, even a very low diamond volume fraction, generated a significant increase in compressive strength. With increasing the diamond volume fraction, the compressive strength was also increased due to the addition of hardest diamonds. It suggests that these composites would be potential candidates for a new cutting tool material.

• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.142-148
• /
• 1995

2219 aluminum alloy bonded diamond wheels containing intermetallic compounds were fabricated by powder metallurgy method. Nickel and titanium were added in aluminum matrix piece. The hot pressing condition was $600^{\circ}C$ and 20 Mpa in the furnace of the electric resistance type. The mechanical properties and grinding tests were carried out to confirm the wheel performance. Aluminum oxide ceramics were chosen for use in the grinding tests. The test proved that the heat resistance 2219 aluminum bonded diamond wheel containing 15 wt% nickel and 15 wt% titanium respectively showed the best performance.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.875-876
• /
• 2006

For dry machining of mineral materials the Institute of Materials Engineering pursues a novel thermal protection shield concept for diamond tools, in which thermal insulating materials in diamond composite structures act as heat shield, which protects diamonds in deeper layers against high temperature and graphitisation. Before the effectiveness of this concept could be investigated suitable composites have to be manufactured. In this paper the powder metallurgical production processes of diamond-alumina-cobalt-composites with varying alumina and cobalt particle sizes, their microstructures and porosities are described. It could be observed that the distribution of small-sized alumina particles ($<70{\mu}m$) in the cobalt matrix is uniform and the porosity of the composite decrease.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1130-1131
• /
• 2006

We found that the """interface reaction between Ni-based alloy bond, diamond, and steel core is very critical in bond strength of diamond tool. None element from metal bond diffuses into the steel core but the Fe element of steel core was easily diffused into the bond. This diffusion depth of Fe has a great effect on the bonding strength. The Cr in steel core accelerated the Fe diffusion and improved the bond strength, on the other hand, carbon decreased the strength. Ni-based alloy bond including Cr was chemically bonded with diamond by forming Cr carbide. However, the Cr and Fe in STS304 were largely interdiffused, the strength was very low. The Cr passivity layer formed at surface of STS304 made worse strength at commissure in brazing process.

• 한국분말재료학회지
• /
• 제15권6호
• /
• pp.509-513
• /
• 2008

High-pressure abrasive entrained jet have rapidly become important machining technology over the last two decades. However, suspension jet by high-pressure has been recently developed for packaging sawing. Ideally, diamond materials should be used for components in abrasive water-jet systems that are subject to high erosive conditions. Using the diamond orifices improve maintenance and extend wear part life. This paper gives insights to using an abrasive suspension jet with diamond orifice. The influences of orifice material and orifice design are evaluated.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1309-1310
• /
• 2006

High-purity and super-hard nano-polycrystalline diamond has been successfully synthesized by direct conversion from high-purity graphite under static pressures above 15 GPa and temperatures above $2300^{\circ}C$. This paper describes research findings on the formation mechanism of nano-structure and on the contributing factor leading to high hardness.

• 한국분말재료학회지
• /
• 제10권3호
• /
• pp.201-208
• /
• 2003

Distributions of diamond particles protruding on the surface of worn diamond segments in circular saw has been investigated. Scanning electron microscope was used to examine the worn ,surface and radial saw blade wear and grinding ratio was measured. The number of protruded diamond particle was approximately 50% of the total number of particles, and that was independent of diamond particle concentration and table speed. It was also noted that the inter-particle distance did not follow a symmetric function like Gaussian distribution function, instead it fitted well with a probability density function based on gamma function. The distribution of inter-particle spacing, therefore, was analyzed using a gamma function model.

• 한국진공학회지
• /
• 제17권6호
• /
• pp.538-543
• /
• 2008

나노급 다이아몬드는 최근 폭발법이나 증착법에 의한 신공정으로 100 nm 이하의 분말형태의 제조가 가능하다. 나노급 다이아몬드의 소결을 이용하면 이상적인 연마기기의 제작이 가능하다. 이러한 나노급 다이아몬드의 소결 공정에서 생기는 비이상적인 나노결정의 결정립성장과 다이아몬드 결합장애를 방지하기 위해서 나노급 무기물을 균일하게 코팅하는 공정개발이 필요하다. 본 연구에서는 나노급 다이아몬드의 소결 특성을 향상시키기 위해서 ALD(atomic layer deposition)을 이용하여 진공에서 $20{\sim}30\;nm$ 두께의 ZnO 박막을 코팅해 보았다. 나노급 다이아몬드 분말 전면에 경제적으로 ZnO ALD를 위해서 기존의 기계적 진동효과 또는 전용 fluidized bed reactor를 대치하여 새로이 20 mm 석영튜브 안에 다이아몬드 분말을 넣고 다공성 유리필터로 막은 후 펄스와 퍼지 공정시의 압력에 의한 다이아몬드의 부유를 이용한 변형된 fluidized bed 공정을 채용하였다. 다공성 유리필터로 양쪽이 막힌 석영튜브 안에 전구체 DEZn (diethylzinc : $C_4H_{10}Zn$)와 반응기체 $H_2O$를 사용하여 ZnO 박막을 캐니스터 온도 $10^{\circ}C$에서 원자층증착하였다. 공정 순서 및 반응물질 주입 시간은 DEZn pulse-0.1초, DEZn purge-20초, $H_2O$ pulse-0.1초, $H_2O$ purge-40초와 같이 설정하였으며, 이 네 단계를 1 cycle로 정의하여 100 cycle 반복 실시하였다. 다이아몬드 분말과 ZnO 박막이 증착된 다이아몬드 분말의 미세구조를 확인하기 위하여 투과전자현미경 (transmission electron microscope)을 이용하였다. TEM 측정결과, ALD 증착 전 나노급 다이아몬드 분말의 직경이 약 $70{\sim}120\;nm$이었고 사면체, 육면체 등의 다양한 형태를 보임을 확인하였다. ZnO 박막이 ALD코팅된 다이아몬드 분말의 직경은 약 $90{\sim}150\;nm$이었고, 다이아몬드 분말과 ZnO의 명암차이에 의해 약 $20{\sim}30\;nm$ 두께의 균일한 ZnO 박막이 다각형 형태의 다이아몬드 파우더 표면에 성공적으로 증착되었음을 확인하였다.

• 한국표면공학회지
• /
• 제50권3호
• /
• pp.177-182
• /
• 2017

The properties of electroless Ni-B thin film on diamond powder with different parameters (temperature, pH, surfactant etc.) were studied. The surface morphology, structure and composition distribution of the Ni-B film were observed by field effect scanning electron microscope (FE-SEM), energy-dispersive spectrometer (EDS), X-ray diffraction (XRD) and Auger electron spectroscopy (AES). The growth rate of Ni-B film was increased with increase of bath temperature. The B content in Ni-B film was reduced with increase of bath pH. As a result the structure of Ni-B film was changed from amorphous to crystalline structure. The PVP in solution plays multi-functional roles as a dispersant and a stabilizer. The Ni-B film deposited with adding 0.1 mM-PVP was strongly introduced an amorphous structure with higher B content (25 at.%). Also the crystallite size of Ni-B film was reduced from 12.7 nm to 5.4 nm.