• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2333-2337
• /
• 2012

We report the synthesis and thermal annealing of Si-core/ZnO-shell nanorods using a two-step process comprising the metal-assisted electroless etching of Si and the sputter deposition of ZnO. Transmission electron microscopy and X-ray diffraction analysis showed that the cores of the annealed core-shell nanorods were single crystal diamond cubic-type Si, whereas the shells of the annealed core-shell nanorods were single crystal wurtzite-type ZnO. The PL spectra of Si nanorods consisted of a broad red emission band and a weaker blue emission band. The major emission band of Si nanorods was shifted from 700 nm (in the red region) to 440 nm (in the violet region) by ZnO coating. The violet emission of the core-shell nanorods was enhanced in intensity considerably by annealing in an oxidizing atmosphere. The origin of the PL enhancement by annealing is also discussed.

• Journal of Ceramic Processing Research
• /
• v.23 no.4
• /
• pp.436-442
• /
• 2022

Gallium nitride (GaN) substrates were ground in two different grinding wheel abrasive sizes of 270 and 800-mesh, and thechange in surface morphologies of the substrates and the depth of subsurface damage (SSD) were observed. With the 800-meshgrinding wheel, the surface roughness (SR) and the depth of SSD of the sample tended to decrease, which was not the casewith the 270-mesh grinding wheel. In the X-ray rocking curve, the sample exhibited some compressive stress with the 270-meshgrinding wheel, but with the 800-mesh grinding wheel, it demonstrated the occurrence of tensile stresses in the sample and adecrease in full width at half maximum (FWHM), which confirms an improvement in the crystallinity. In the Raman spectra,the compressive stress of the 270-mesh grinding wheel and the tensile stress of the 800-mesh grinding wheel were confirmedthrough peak shifts. Photoluminescence (PL) spectra confirmed that the intensity ratio of the yellow luminescence increasedat the 800-mesh grinding wheel, and a blue shift occurred further. These results indicate that the SR and the depth of SSDwere proportional to the abrasive grain size of the grinding wheel. At the same time, the increase in PL intensity at specificpeak positions indicates that the stress stemming from the grinding process was concentrated at the crystal surface. The abovemechanism is illustrated in a schematic diagram, which confirms the possibility of improving the grinding efficiency andsubsequent polishing processes in future applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.1
• /
• pp.21-26
• /
• 2020

This article reports the result on the spectroscopic analysis of the three Lightbox CVD-grown diamonds. Lightbox Jewelry, a De Beers company, has begun selling CVD laboratory-grown diamonds since September 2018. Recently, we had the opportunity to examine three Lightbox's pendant necklaces. The 0.25 ct, 0.25 ct, and 0.26 ct round brilliant were graded as "H" near colorless, Fancy Vivid orangy pink, and Fancy Vivid blue with cut grades of excellent, respectively. The laser-inscribed Lightbox logo under the table, large enough to be easily visible with a microscope. Based on the spectroscopic techniques, for near colorless sample was not subjected to post-growth HPHT processing to improve its color. For pink sample, optical centers at H3, 3H, 594 nm, NV, and GR1 were recorded. It was speculated that the pink sample have been received irradiation and annealing. In addition, the blue CVD synthetic sample was concluded to be irradiated without annealing.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.5
• /
• pp.235-240
• /
• 2013

Pure-carbon materials such as graphite, graphene, carbon nanotubes, and diamond have very high thermal conductivities. The reported thermal conductivity of graphene is in the range 3000~5000W/m-K at room temperature. Here, we developed graphene/cu foam hybrid type heat spreader to obtain higher thermal conductivity than Cu foam. Hybrid materials were characterized using optical microscopy (OM), scanning electron microscopy (SEM) and thermal conductivity measurement system; LFA (Laser Flash Analysis @ LFA 447, NETZSCH). We suggest that excellent thermal properties of graphene/cu foam hybrid structures are beneficial for all proposed electrical applications and can lead to a thermal management application.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.239-244
• /
• 2019

Two hydrogenation surface modifications, namely hydrogen atmosphere heat treatment and hydrogen plasma treatment, were found to lead to improved dispersion of nanodiamond (ND) seed particles and enhanced nucleation density for deposition of smooth ultrananocrystalline diamond (UNCD) film. After hydrogenation, the C-O and O-H surface functionalities on the surface of nanodiamond particles were converted to the C-H surface functionalities, and the Zeta potential was increased. As the degree of dispersion was improved, the size of nanodiamond aggregates decreased significantly and nucleation density increased dramatically. After hydrogen heat treatment at 600℃, average size of ND particles was greatly reduced from 3.5 ㎛ to 34.5 nm and a very high nucleation of ~3.9 × 10¹¹ nuclei/㎠ was obtained for the seeded Si surface.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.145-152
• /
• 2015

In this work, we were investigated the effect of the additive gases on the relationship between bonding structure and mechanical properties of the deposited films when the DLC films were deposited on Si-wafer by the rf-PECVD method with the addition of small amounts of carbon dioxide and nitrogen to the mixture gas of methane and hydrogen. The deposition rate of the films increased as the rf-power increased, while it decreased with increasing the amount of additive gases. Also, as the carbon dioxide gas increased, the hydrogen content in the films decreased but the $sp^3/sp^2$ ratio of the films increased. In case of nitrogen gas, the hydrogen content decreased, however the $sp^3/sp^2$ ratio and nitrogen gas flow rate did not show a specific tendency.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.1
• /
• pp.33-40
• /
• 2014

Poly vinylidene fluoride-co-hexafluoropropylene (PVdF-HFP) membrane were prepared by the electrospinning technique. We had applied a DLC coating process and then the surface of the membrane and the contact angle change was investigated. Electrospun fibrous PVdF-HFP membrane surface became to wrinkled shape by Ar plasma treatment and treatment conditions. The wrinkled surface of PVdF-HFP membrane became super-hydrophilic. However, after DLC coating process, it became super-hydrophobic. The resulting surfaces were characterized by water contact angle measurement, X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM). Resultantly it was recognized that the wettability characteristics of the membrane surfaces depended on the chemical composition and surface morphology.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.5
• /
• pp.831-836
• /
• 2013

This study demonstrates the process of fabricating patterns using tribonanolithography (TNL),with laboratory-made micro polycrystalline diamond (PCD) tools that are attached to an atomic force microscope (AFM). The various patterns are easily fabricated using mechanical scratching, under various normal loads, using the PCD tool on single crystal silicon, which is the master mold for replication in this study. Then, polydimethylsiloxane (PDMS) replica molds are fabricated using precise pattern transfer processes. The transferred patterns show high dimensional accuracy as compared with those of TNL-processed silicon micro molds. TNL can reduce the need for high cost and complicated apparatuses required for conventional lithography methods. TNL shows great potential in that it allows for the rapid fabrication of duplicated patterns through simple mechanical micromachining on brittle sample surfaces.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.99-104
• /
• 2004

Micro/meso cutting is getting more important in the fields of precision machining technology. A micro-turning lathe is one of parts to consist the Micro Factory. It accepts stepwise motion actuators that are used for feeding system instead of the conventional mechanism. It is consisted of two Piezoelectric ceramics; one is for feeding the slider, and the other is for clamping the slider in the guide way of the body. The linearity and positional accuracy of the actuators are good enough for high precision motion. The spindle unit is operated with DC motor on the top of the slider. The motion is communicated with miniaturized linear encoder attached on each side of axis. A mono crystal diamond tool is used for cutting tool. This micro-lathe has been made a machining experiment to see the characteristics of micro-machining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.623-624
• /
• 2005

Micro injection molding is a branch of micro system technology and has been under development for the mass manufacture of micro parts. Enhanced technological products like micro optical devices are entering the market. This paper presents fundamental research on the injection molding technique in micro fabrication. In order to successful manufacturing of micro plastic parts, it is necessary to research for development of micro-injection machine, machining of micro mold, decision of optimum injection conditions and the research for polymer material. Therefore in this study, in order to machining of micro mold, a mold core with microscopic V-shaped groove was tooled by ultra-precise tooling machine. The transcription experiments with a polymer, PMMA resin on the surface of core with Ni plating were carried out and surface profile of injected parts was measured with AFM.