• Korean Journal of Crystallography
• /
• v.6 no.1
• /
• pp.14-26
• /
• 1995

The growth mechanism of diamond thin films, deposited by Hot Filament CVD, was investigated through observation of changes in their surface morphology as a function of the substance temperature and deposition time. Amorphous carbon or DLC thin films were deposited at low substrate temperature. Diamond films consisting of square-shaped particles, whose surfaces are (100) planes, were deposited at an intermedate temperature. At high substrate temperatures, diamond films consisting of the particles showing both (100) and (111) plane were deposited. The (100) proferred orientation of the diamond films are believed to be due to a relatively high supersaturation during deposition, and the growth condition for the diamond films having (100) preferred orientation can be applied to the single crystal growth since no twins are generated on the (100) plane. The grain size of the diamond films did not change with increasing temperature and its increasing rate with increasing deposition time was the same irrespective of the substrate temperature. However, the nucleation density increased with substrate temperature and its increasing rate with deposition time was much higher for the films deposited at higher substrate temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.905-908
• /
• 2000

The growth properties of diamond grain were examined by Raman spectroscopy and microscope images. Diamond thin films were prepared on single crystal Si wafers by microwave Plasma chemical vapor deposition. Preparation conditions, substrate temperature, boron concentration and deposition time were controlled differently. Prepared diamond thin films have different surface morphology and grain size respectively Diamond grain size was gradually changed by substrate temperature. The biggest diamond grain size was observed in the substrate, which has highest temperature. The diamond grain size by boron concentration was slightly changed but morphology of diamond grain became amorphous according to increasing of boron concentration. Time was also needed to be a big diamond grain. However, time was not a main factor for being a big diamond grain. Raman spectra of diamond film, which was deposited at high substrate temperature, showed sharp peaks at 1334$cm^{-1}$ / and these were characteristics of crystalline diamond. A broad peak centered at 1550$cm^{-1}$ /, corresponding to non-diamond component (sp$^2$carbon), could be observed in the substrate, which has low temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.7
• /
• pp.552-556
• /
• 1998

Diamond thin films were deposited on Si substrate using $CH_4 and H_2$mixed gas by RF plasma CVD. Prior to deposition, the substrate surface was mechanically scratched with the diamond paste of $3{\mu}m$ to improve the density of nucleation sites. The microstructure of diamond films deposited with methane(0.5%~2%) at the reaction pressure ranging from 20 torr to 50torrr were studied by a scanning electron microscope. It was observed in the deposited diamond films that the nucleation density decreased and crystallinity increased with decreasing the methane concentration. However, the nucleation density and crystallinity were decreased with decreasing the process pressure.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.1
• /
• pp.33-38
• /
• 2002

In this study, the metastable state diamond thin films have been deposited on Si substrates from methane-hydrogen and oxygen mixture using microwave plasma enhanced chemical vapor deposition (MPCVD) method. Effects in experimental parameters of MPCVD including methane concentrations, oxygen additions, operating pressure, deposition time on the growth rate and crystallinity were investigated. Diamond thin film was synthesized under the following conditions: methane concentration of 0.5%(0.5sccm)~5%(5sccm), oxygen concentration of 0~80%(2.4sccm), operating pressure of 30Torr~70Torr, deposition time of 1~32hr. SEM, XRD, and Raman spectroscopy were employed to analyze the growth rate and morphology, crystallinity and prefered growth direction, and relative amounts of diamond and non-diamond phases, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.403-409
• /
• 1999

We fabricated diamond like carbon (DLC) thin films using pulsed laser deposition (PLD) method. Among many deposition parameters, the effects of the deposition temperature and the laser energy density were investigated. Structural properties of the films were studied by Raman spectroscopy. The surface morphologies and cross-section imagies of the films were investigated by atomic force microscopy (AFM) and scanning electron microscopy (SEM) respctively. DLC thin films fabricated at $12 J/cm^2$ of a laser energy density and $300^{\circ}C$ of a deposition temperature showed the best quality.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.19-27
• /
• 2003

Morphology and composition of MgO films grown on single-crystalline diamond (100) have been studied. MgO thin films were deposited in the substrate temperature range from room temperature (RT) to 723K by means of electron beam evaporation using MgO powder source. Atomic force microscopy images indicated that the film grown at RT without $O_2$ supply was relatively uniform and flat whereas that deposited in oxygen ambient yielded higher growth rates and rough surface morphologies. X-ray photoelectron spectroscopy analyses demonstrate that the MgO film deposited at RT without $O_2$ has the closest composition to the stoichiometric MgO, and that a thin contaminant layer composed mainly of magnesium peroxide (before etching) or hydroxide (after etching) was unintentionally formed on the film surface, respectively. These results will be discussed in relation to the interaction among the evaporated species and intentionally supplied oxygen molecules at the growth front as well as the interfacial energy between diamond and MgO.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1330-1332
• /
• 1998

Polycrystalline diamond films are deposited on a Si substrate by employing a 2.45 GHz $\mu$-wave plasma CVD system. Prior to depositing the diamond film, a DPR(diamond photo-resist) layer is coated to enhance the nucleation density. The growth rate of diamond films increases with the $\mu$-wave power and approaches to be about $1.5{\mu}m/hr$ at 1100 W. Structural properties of diamond films deposited are characterized from their SEM photographs, Raman spectra, and AFM surface images. Lager grain size, higher intensity of diamond peak, and smoother surface are observed for films deposited at a higher power. The possible mechanism on the diamond growth is also discussed to explain the experimental results.

• Korean Journal of Crystallography
• /
• v.7 no.2
• /
• pp.175-182
• /
• 1996

ZnO thin films were deposited on Corning 7059 glass substrates to study fundamental properties of films. According to the experimental results, (002) preferred ZnO thin films were grown by purging Ar/O2 mixed gas, but not without oxygen gas. The structure and the orientation of ZnO thin films were much affected by the substrate temperature and rf power. High quality ZnO films were obtained by increasing their values. Optimum deposition parameters were : 300W rf power, 300℃ substrate temperature, Ar/O2=70/30. To characterize SAW propagation properties, IDT was fabricated by etching Al films deposited on diamond/Si wafer with RIE. Measured λ(wavelength) was 24μm and experimental results were well matched with simulation. Center frequency was 250MHz, and the calculated phase velocity of ZnO/ diamond structure was about 6000m/s.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.97-100
• /
• 1990

Diamond thin films were synthesized by the MPECVD (Microwave Enhanced Chemical Deposition) using the mixture of the hydrogen and organic compounds($CH_3COCH_3$, $CH_3OH$). In X-ray Diffraction, the d values of all the deposits on the Si substrates with the experimental conditions coincide with those of natural diamond in POD (Powder Diffraction Data). The changes of the morphology of all the deposits were examined by SEM. The amount of amorphous carbon or graphite in the diamond films were increased as the acetone concentration was increased. The morphology of the diamond particles can be changed from ball-like to euhedral by adding the small amount of the methanol in the reaction gases of the high acetone concentration.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.06a
• /
• pp.49-54
• /
• 1998

The growth of diamond films in plasma enhanced chemical vapor deposition(PECVD) processes requires high substrate temperatures and gas pressures, as well as high-power excitation of the gas source. Thus determining the substrate temperature in this severe environment is a challenge. The issue is a critical one since substrate temperature is a key parameter for understanding and optimizing diamond film growth. The precise Si substrate temperature calibration based on rapid-scanning spectroscopic ellipsometry have been developed and utilized. Using the true temperature of the top 200 ${\AA}$ of the Si substrate under diamond growth conditions, real time spectroellipsometry (RTSE) has been performed during the nucleation and growth of nanocrystallind thin films prepared by PECVD. RTSE shows that a significant volume fraction of nondiamond(or{{{{ {sp }^{2 } -bonded}}}}) carbon forms during thin film coalescence and is trapped near the substrate interface between ∼300 ${\AA}$ diamond nuclei.