• Journal of Veterinary Clinics
• /
• v.29 no.1
• /
• pp.107-111
• /
• 2012

Three dogs (An 8 years-old intact female Poodle, a 7 years-old intact male Schunauzer, and an 8 yearsold Golden Retriever) were presented due to acute vomiting, dyspnea, and generalized weakness. Megaesophagus was confirmed through radiographic examination in all 3 dogs. Relative oesophageal diameter (ROD) was measured and results of ROD measurements showed the possibility of megaesophagus secondary to myasthenia gravis in three dogs. Thus we performed anticholinesterase test as screening test for myasthenia gravis. In all three dogs, esophageal diameter was reduced after neostigmine methylsulfate administration. For definite diagnosis of acquired myasthenia gravis, serum acetylcholine receptor antibody titer was measured, but definite diagnosis was confirmed only in one case. However, based on history, radiographic findings, anticholinesterase test, ROD measurement, other two cases were still suspected as megaesophagus secondary to myasthenia gravis. Treatment with pyridostigmine bromide was initiated in all dogs, and improvement of esophageal diameter was shown in all dogs. One dog was successfully managed for 15 months after initial treatment and, is still alive, but other two dogs were died shortly after initial treatment, because of severe aspiration pneumonia.

• Journal of the Korea Furniture Society
• /
• v.26 no.2
• /
• pp.179-185
• /
• 2015

A study was carried out to observe the 1% aqueous safranine solution flow speed in longitudinal and radial directions of softwood G. biloba, ring-porous wood A. altissima, and diffuse- porouswood D. kaki. In radial direction, ray cells and in longitudinal direction tracheids, vessel and wood fiber were considered for the measurement of liquid penetration speed at less than 12% moisture contents (MC). The length, lumen diameter, pit diameter, end wall pit diameter and the numbers of end wall pits determined for the flow rate. The liquid flow in the those cells was captured via video and the capillary flow rate in the ones were measured. Vessel in hardwood species and tracheids in softwood was found to facilitate prime role in longitudinal penetration. Radial flow speed was found highest in ray parenchyma of G. biloba. Anatomical features like the length and diameter, end-wall pit numbers of ray parenchyma were found also responsible fluid flow differences. On the other hand, vessel and fiber structure affected the longitudinal flow of liquids. Therefore, the average liquid penetration depth in longitudinal tracheids of G. biloba was found the highest among all cells considered in D. kaki and A. altissima.

• Journal of Veterinary Clinics
• /
• v.14 no.2
• /
• pp.287-296
• /
• 1997

Serial ultrasonographic examinations were daily performed on 8 bitches (5 Maltese and 3 Yorkshire terrier) from day 15 until parturition to determine the size of gestational structures. Gestational age was timed from the day of ovulation (day 0), which was estimated to occur when plasma progesterone concentration was first increased above 4.0 ng/ml. When the size of fetal and extra-fetal structures according to gestational age was measured, there was a difference between Maltese and Yorkshire terrier in extra-fetal structures (P<0.001), and no difference in fetal structrures (P<0.001). The correlations between the gestational age and the growth in fetal and extra-fetal structures were examined by regression analysis. The extra-fetal structure which showed high correlation from day 20 to 35 was inner chorionic cavity diameter in two breeds. The fetal structures which showed high correlation from day 36 until parturition was fetal head diameter in two breeds. In conclusions inner chorionic cavity diameter was the most accurate for estimation of gestational age and prediction of whelping day from day 20 to 35, and fetal head diameter from day 36 to parturitions respectively. Ultrasonography is very useful tool to evaluate the gestational age and to predict the whelping day in pet dogs.

• Particle and aerosol research
• /
• v.13 no.2
• /
• pp.53-63
• /
• 2017

As semiconductor process was highly integrated, particle contamination became a major issue. Because particle contamination is related with process yields directly, particles with a diameter larger than half pitch of gate should be controlled. PBMS (Particle beam mass spectrometry) is one of powerful nano particle measurement device. It can measure 5~500 nm particles at ~ 100 mtorr condition in real time by in-situ method. However its usage is restricted to research filed only, due to its big device volume and high price. Therefore aperture changeable aerodynamic lenses (ACALs) which can control particle focusing characteristics by changing its aperture diameter was proposed in this study. Unlike conventional aerodynamic lenses which changes particle focusing efficiency when operating condition is changed, ACALs can maintain particle focusing efficiency. Therefore, it can be used for a multi-monitoring system that connects one PBMS and several process chambers, which greatly improves the commercialization possibility of the PBMS. ACALs was designed based on Stokes number and evaluated by numerical method. Numerical analysis results showed aperture diameter changeable aerodynamic lenses can focus 5 to 100 nm standard particles at 0.1 to 10 torr upstream pressure.

• Korea-Australia Rheology Journal
• /
• v.17 no.4
• /
• pp.157-164
• /
• 2005

Hydrodynamic characteristic of surfactant drag-reducing flows is still not fully understood. This work investigated the temperature and diameter effect on hydrodynamic characteristic of cationic surfactant drag reducing flows in pipes. Solution of oleyl bishydroxyethyl methyl ammonium chloride (Ethoquad O/12), 900 ppm, as a cationic surfactant and sodium salicylate (NaSal), 540 ppm, as a counter-ion was tested at 12, 25, 40, and $50^{\circ}C$ in pipes with diameter of 13, 25, and 40 mm. Drag reduction effectiveness of this surfactant solution was evaluated in 25 mm pipe from 6 to $75^{\circ}C$. Rheological characteristic of this solution was measured by stress control type rheometer with cone-and-plate geometry. Scale-up laws proposed by previous investigators were used to evaluate the flow characteristic of the solution. It was found that this surfactant solution has clear DR capability until $70^{\circ}C$. Result of this work suggested that temperature has a significant influence in changing the hydrodynamic entrance length of surfactant drag reducing flows. From rheological measurement, it was found that the solution exhibits Shear Induced Structure at all temperatures with different degree of peak viscosity and critical shear rate.

• Nuclear Engineering and Technology
• /
• v.39 no.4
• /
• pp.349-358
• /
• 2007

A single-beam gamma densitometer is utilized to measure the average void fraction in a small diameter stainless steel pipe under critical flow conditions. A typical design of a single-beam gamma densitometer is composed of a sealed gammaray source, a collimator, a scintillation detector, and a data acquisition system that includes an amplifier and a single channel analyzer. It is operated in the count mode and can be calibrated with a test pipe and various types of phantoms made of polyethylene. A good average void fraction is obtained for a small diameter pipe with various flow regimes of the core, annular, stratified, and bubbly flows. Several factors influencing the performance of the gamma densitometer are examined, including the distance between the source and the detector, the measuring time, and the ambient temperature. The void fraction is measured during an adiabatic downward two-phase critical flow in a vertical pipe. The test pipe has an inner diameter of 10.9 mm and a thickness of 3.2 mm. The average void fraction was reasonably measured for a two-phase critical flow in the presence of nitrogen gas.

• Korean Journal of Materials Research
• /
• v.34 no.7
• /
• pp.355-362
• /
• 2024

AR (alkali resistant)-glass fibers were developed to provide better alkali resistance, but there is currently no research on AR-glass fiber manufacturing. In this study, we fabricated glass fiber from AR-glass using a continuous spinning process with 40 wt% refused coal ore. To confirm the melting properties of the marble glass, raw material was put into a (platinum) Pt crucible and melted at temperatures up to 1,650 ℃ for 2 h and then annealed. To confirm the transparent clear marble glass, visible transmittance was measured and the fiber spinning condition was investigated by high temperature viscosity measurement. A change in diameter was observed according to winding speed in the range of 100 to 700 rpm. We also checked the change in diameter as a function of fiberizing temperature in the range of 1,240 to 1,340 ℃. As winding speed increased at constant temperature, fiber diameter tended to decrease. However, at fiberizing temperature at constant winding speed, fiber diameter tended to increase. The properties of the prepared spinning fibers were confirmed by optical microscope, tensile strength, modulus and alkali-resistance tests.

• The Journal of Korean Academy of Prosthodontics
• /
• v.36 no.3
• /
• pp.468-482
• /
• 1998

Since the concept of osseointegration was introduced by Branemark of Sweden, dental implants have been used for various dental prosthetic treatments. The survival rate of dental implant is likely to be closely related to the total biomechanical role of each component of implant system. The use of interchangeable component is very attractive for dental practitioners because such an approach would save treatment cost, flexibility of prosthetic treatment options as well as conveniences. Therefore, the use of interchangeable implant system has been increasing without scientific assessment of safety and efficacy of various interchangeable implant system. The purpose of this study, therefore, were to compare the geometric characteristic of four interchangeable dental implant screws and the loosening torque of these screws. Four types of dental implant screws tested in this study were Nobelpharma, 3i, Impla-med, Restore. Four screws each of the test specimens were subjected for scanning electron microscopic examinations under the same condition and a 35x magnified standard SEM picture was objected from each test specimen using JSM-5200 scanning microscope. From each of the SEM pictures, eight parameters. i.e., diameter of screw head. screw length, thread pitch, major diameter. neck diameter, neck length, crest width and root width were determined using a caliper. The measurement for each parameters were then corrected for their magnification factor. The loosening torque were also determined by using a torque gauge. All of the measurements were statistically analyzed by ANOVA test and multiple range test. Statistical significance was set in advance at the probability level of less than 0.05. All analyses were done with SPSS software for the personal computer. The conclusion obtained from this studies were summarized as the following; 1. No statistically significances were noted in the thread pitch. and crest width in the four screws, and in the case of major diameter, the Impla-med screw was significantly smaller than the other three screws (p<0.05). Therefore, four implant bolts could be physically inserted in a abutment nuts. 2. The diameter of screw head was decreased in the order of Restore, 3i, Nobelpharma, Impla-med screws and the length of screws were decreased in the order of 3i, Restore, Nobelpharma and Impla-med. The diameter of neck was decreased in the order of Impla-med, Restore. Nobelpharma, 3i screws. The differences of each of these parameters were statistically significant (p<0.05). The width of root of screws were decreased in the order of Nobelpharma, Impla-med, Restore and 3i. The differences among Nobelpharma and Impla-med. Restore and 3i were statistically significant (p<0.05). 3. When the screws were loosening 1, 3, 4 and 5 times, the loosening torque for Impla-med and 3i screws were significantly higher than that of Nobelpharma or Restore screws (p<0.05). However, when statistically smaller than that of 3i, Restore or Nobelpharma screws(p<0.05).

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.1
• /
• pp.38-46
• /
• 2016

In this study, the bleeding tests were performed to investigate the effects of cement paste(w/c=0.42) on bleeding through varying the number of strand and the diameter of cylinder. The test variables were specified by differing the diameter of cylinder and the number of strand. The bleeding test was performed with respect to all diameter parameters by with or without strand. In addition, the number of strands were specified at four levels, 0, 1, 2, and 3 EA in case of 50 mm cylinder. In case of without strand, the bleeding rate was determined at low level under 2%. Moreover, all of the specimens had similar value in the measurement error. In case of with strand, maximum bleeding rate was 10%. As the diameter of cylinder decreased, the bleeding rate was decreased. The bleeding rate was altered rapidly in between 50 to 100mm of diameter. Even though bleeding rate was increased according to the increase in the number of strand, these tendency for bleeding rate was negligible with the measurement error.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.381-382
• /
• 2010