• Progress in Medical Physics
• /
• v.27 no.1
• /
• pp.31-36
• /
• 2016

The paper discusses radiation dose of dual energy CT on which copper modulation layer, is mounted in order to improve diagnostic performance of the dual energy CT. The radiation dose is estimated using MCNPX and its results are compared with that of the conventional dual energy CT system. CT X-ray spectra of 80 and 120 kVp, which are usually used for thorax, abdominal, head, and neck CT scans, were generated by the SPEC78 code and were used for the source specification 'SDEF' card for MCNPX dose modeling. The copper modulation layer was located 20 cm away from a source covering half of the X-ray window. The radiation dose was measured as changing its thickness from 0.5 to 2.0 mm at intervals of 0.5 mm. Since the MCNPX tally provides only normalized values to a single particle, the dose conversion coefficients of F6 tally for the modulation layer-based dual energy CBCT should be calculated for matching the modeling results into the actual dose. The dose conversion coefficient is $7.2*10^4cGy/output$ that is obtained from dose calibration curve between F6 tally and experimental results in which GAFCHORMIC EBT3 films were exposed by an already known source. Consequently, the dose of the modulation layer-based dual energy cone beam CT is 33~40% less than that of the single energy CT system. On the basis of the results, it is considered that scattered dose produced by the copper modulation layer is very small. It shows that the modulation layer-based dual energy CBCT system can effectively reduce radiation dose, which is the major disadvantage of established dual energy CT.

• Journal of the Korean earth science society
• /
• v.26 no.6
• /
• pp.524-540
• /
• 2005

This study has focused on the amount of evaporites and geochemical characteritics of evaporites from the acid mine drainage and on the variation of constituents in acid mine drainage during evaporation. The various colors of evaporites are frequently observed at the rock surfaces contacting acid mine drainage. In order to produce evaporites in the laboratory, acid mine drainages were sampled from the abandoned mine areas (GTa, GTb, GH and GB) and air-dried at room temperature. During the evaporation of acid mine drainages, TDS, EC values and the concentrations of major and minor ions increased, whereas ER and DO values decreased with time. The concentration of Fe increased gradually with evaporation time in the GTb and GB, whereas GH founded in one day but rapidly not detected in the other day after due to removal of Fe by formation-precipitation of amorphous Fe hydroxide. The amounts of the evaporites were produced in amounts of 4 g (GTa), 5 g (GB), 15 g (GH), and 24 g (GTb) from 4 liter of acid mine drainage after 80 days of the evaporation, respectively. In linear analysis from the products with the parameters which are the EC, TDS, salinity, ER, DO and pH contents in field, the determination coefficients were 0.98, 0.99, 0.98, 0.88, 0.89, and 0.25 respectively. If we measure the parameters in field, it would be easy to estimate the amount of evaporites in acid mine drainage. Gypsum and epsomite were identified in all of the evaporites by x-ray powder diffraction studies. Evaporite (GTb) was heated at 52, 65, 70, 95, 150, 250, and 350oC for one hour in electrical furnaces. Gypsum, $CaSO_4\cdot1/2H_2O$ and kieserite were identified in the heated evaporite by XRD. With increased heating temperature, the intensity of the peak at $7.66/AA$ (diagnostic peak of gypsum), the peak at 5.59A ($CaSO_4{\cdot}1/2H_2O)$ and the peak at $4.83{\AA}$ (kieserite) decreased in x-ray diffraction due to dehydration. In the SEM and EDS analysis for the evaporite, gypsum of well-crystallized, radiating cluster of fibrous, acicular, and columnar shapes were observed in all samples. Ca was not detected in the EDS analysis of the flower structures of GTb. Because of that, the evaporite with flower structures is thought to be eposmite.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.2
• /
• pp.232-240
• /
• 1997

Background : Postprimary pulmonary tuberculosis is located mainly in upper lobes. The tuberculous lesion involving the lower lobes usually arises from the upper lobe cavity through endobronchial spread. When tuberculosis is confined to the lower lung field, it often masquerades as pneumonia, lung cancer, bronchiectasis, or lung abscess. Thus the correct diagnosis may be sometimes delayed for a long time. Methods : We carried out, retrospectively, a clinical study on 50 patients confirmed with lower lung field tuberculosis who visited the Department of Pulmonary Medicine at Hanyang University Hospital from January 1992 to December 1994. The following results were obtained. Results : Lower lung field tuberculosis without concomitant upper lobe disease occurred in fifty patients representing 6.9% of the total admission with active pulmonary tuberculosis over a period of 3 years. It occurred most frequently in the third decade but age distribution was relatively even. The mean age was 43 years old. Female was more frequently affected than male (male to female ratio 1 : 1.9). The most common symptom was cough(68%), followed by sputum(52%), fever(38%), and chest discomfort(30%). On chest X-ray of the 50patients, consolidation was the most common finding in 52%, followed by solitary nodule(22%) collapse(16%), cavitary lesion(10%), in decreasing order. The disease confined to the right side in 25 cases, left side 20 cases, and both sides 5 cases. Endobronchial tuberculosis (1) Endobronchial involvement was proved by bronchoscopic examination in 20 of 50patients. (2) Mean age was 44years old and female was more affected than man (male to female ratio 1 : 3). Sputum AFB stain and Mycobacterium tuberculosis culture were positive only in 50% of cases unlikely upper lobe tuberculosis, additional diagnostic methods were needed. In our study, bronchoscopic examination and percutaneous fine needle aspiration biopsy increased diagnostic yield by 18% and 32%, respectively. The most common associated condition was diabetes mellitus(18%) and others were anemia, anorexia nervosa, stomach cancer, and systemic steroid usage. Conclusion : When we find a lower lung field lesion, we should suspect tuberculosis if the patient has diabetes mellitus, anemia, systemic steroid usage, malignancy or other immune suppressed states. Because diagnostic yield of sputum AFB smear & Mycobacterium tuberculosis culture was low, additional diagnostic methods such as bronchoscopy and fine needle aspiration biopsy were needed.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.1
• /
• pp.5-19
• /
• 1998

Introduction: Direct histologic and bacteriologic examination of a representative specimen of lung tissue is the only certain method of providing an accurate diagnosis in various pulmonary diseases including diffuse pulmonary diseases. The purpose of national survey was to define the indication, incidence, effectiveness, safety and complication of open and thoracoscopic lung biopsy in korea. Methods: A multicenter registry of 37 university or general hospitals equipped more than 400 patient's bed were retrospectively collected and analyzed for 3 years from the January 1994 to December 1996 using the same registry protocol. Results: 1) There were 511 cases from the 37 hospitals during 3 years. The mean age was 50.2 years(${\pm}15.1$ years) and men was more prevalent than women(54.9% vs 45.9%). 2) The open lung biopsy was performed in 313 cases(62%) and thoracoscopic lung biopsy was performed in 192 cases(38%). The incidence of lung biopsy was more higher in diffuse lung disease(305 cases, 59.7%) than in localized lung disease(206 cases, 40.3%) 3) The duration after abnormalities was found in chest X-ray until lung biopsy was 82.4 days(open lung biopsy: 72.8 days, thoracoscopic lung biopsy: 99.4 days). The bronchoscopy was performed in 272 cases(53.2%), bronchoalveolar lavage was performed in 123 cases(24.1%) and percutaneous lung biopsy was performed in 72 cases(14.1%) before open or thoracoscopic lung biopsy. 4) There were 230 cases(45.0%) of interstitial lung disease, 133 cases(26.0%) of thoracic malignancies, 118 cases(23.1%) of infectious lung disease including tuberculosis and 30 cases (5.9 %) of other lung diseases including congenital anomalies. No significant differences were noted in diagnostic rate and disease characteristics between open lung biopsy and thoracoscopic lung biopsy. 5) The final diagnosis through an open or thoracoscopic lung biopsy was as same as the presumptive diagnosis before the biopsy in 302 cases(59.2%). The identical diagnostic rate was 66.5% in interstitial lung diseases, 58.7% in thoracic malignancies, 32.7% in lung infections, 55.1 % in pulmonary tuberculosis, 62.5% in other lung diseases including congenital anomalies. 6) One days after lung biopsy, $PaCO_2$ was increased from the prebiopsy level of $38.9{\pm}5.8mmHg$ to the $40.2{\pm}7.1mmHg$(P<0.05) and $PaO_2/FiO_2$ was decreased from the prebiopsy level of $380.3{\pm}109.3mmHg$ to the $339.2{\pm}138.2mmHg$(P=0.01). 7) There was a 10.1 % of complication after lung biopsy. The complication rate in open lung biopsy was much higher than in thoracoscopic lung biopsy(12.4% vs 5.8%, P<0.05). The incidence of complication was pneumothorax(23 cases, 4.6%), hemothorax(7 cases, 1.4%), death(6 cases, 1.2%) and others(15 cases, 2.9%). 8) The 5 cases of death due to lung biopsy were associated with open lung biopsy and one fatal case did not describe the method of lung biopsy. The underlying disease was 3 cases of thoracic malignancies(2 cases of bronchoalveolar cell cancer and one malignant mesothelioma), 2 cases of metastatic lung cancer, and one interstitial lung disease. The duration between open lung biopsy and death was $15.5{\pm}9.9$ days. 9) Despite the lung biopsy, 19 cases (3.7%) could not diagnosed. These findings were caused by biopsy was taken other than target lesion(5 cases), too small size to interpretate(3 cases), pathologic inability(11 cases). 10) The contribution of open or thoracoscopic lung biopsy to the final diagnosis was defininitely helpful(334 cases, 66.5%), moderately helpful(140 cases, 27.9%), not helpful or impossible to judge(28 cases, 5.6%). Overall, open or thoracoscopic lung biopsy were helpful to diagnose the lung lesion in 94.4 % of total cases. Conclusions: The open or thoracoscopic lung biopsy were relatively safe and reliable diagnostic method of lung lesion which could not diagnosed by other diagnostic approaches such as bronchoscopy. We recommend the thoracoscopic lung biopsy when the patients were in critical condition because the thoracoscopic biopsy was more safe and have equal diagnostic results compared with the open lung biopsy.

• Korean Journal of Digital Imaging in Medicine
• /
• v.9 no.1
• /
• pp.37-43
• /
• 2007

1. Purpose : This study is to present effective exposure conditions to acquire the best image of simple abdomen in Film Screen (F.S) system and Computed Radiography (C.R) system. 2. Method : In the F.S system, while an exposure condition was fixed as 70kVp, images of a patients simple abdomen were taken under the different mAs exposure conditions. Among these images, the best one was chosen by radiologists and radiological technologists. In the C.R system, the best image of the same patient was acquired with the same method from the F.S system. Both characteristic curves from F.S system and C.R system were analyzed. 3. Results : In the F.S system, the best exposure condition of simple abdomen was 70kVp and 20mAs. In the CR system, with the fixed condition at 70kVp, the image densities of human organs, such as liver, kidney, spleen, psoas muscle, lumbar spine body and iliac crest, were almost same despite different environments (3.2mAs, 8mAs, 12mAs, 16mAs and 20mAs). However, when the exposure conditions were over or under (below) 12mAs, the images between the abdominal wall and the directly exposed part became blurred because the gap of density was decreased. In the C.R system, while the volume of mAs was decreased, an artifact of quantum mottle was increased. 4. Conclusion : This study shows that the exposure condition in the C.R system can be reduced 40% than in the F.S system. This paper concluded that when the exposure conditions are set in CR environment, after the analysis of equipment character, such as image processing system(EDR : Exposure Data Recognition processing), PACS and so on, the high quality of image with maximum information can be acquired with a minimum exposure dose.

• Tuberculosis and Respiratory Diseases
• /
• v.53 no.5
• /
• pp.510-518
• /
• 2002

Background : Bronchial anthracofibrosis (BAF) is a dark black or brown pigmentation of multiple large bronchi associated with a fibrotic stenosis or obliteration that is incidentally found during a diagnostic bronchoscopy some reporters have suggested endobronchial tuberculosis or tuberculous lymphadenitis as a possible cause of BAF. However, some BAF patients do not have any medical history of tuberculosis. The aim of this study was to elucidate the clinical features of simple BAF patients, which were not associated with tuberculosis. Methods : We reviewed the patients' charts retrospectiely and interviewed all BAF patients who were followed up for 1 year or more. Among the 114 BAF patients, 43 patents (38 %) had no associated tuberculosis, cancer and pneumoconiosis. The clinical characteristics, radiological findings and associated pulmonary diseases of these patients were evaluated. Results : Most patients were non-smokers, old aged, housewifes who resided in a farming village. The common respiratory symptoms were dyspnea, cough and hemoptysis. The predominant X-ray findings were a multiple bronchial wall thickening(89%), bronchial narrowing or atelectasis (76%) and a mediastinal lymph node enlargement with/without calcification (78%). Pulmonary function test usually showed mild obstructive ventilatory abnormalities but no patient showed a restrictive ventilatory pattern and the patients were frequently affected with chronic bronchitis(51%), post-obstructive pneumonia(40%) and chronic asthma(4%). Conclusion : Because BAF is frequently associated with chronic bronchitis and obstructive pneumonia as well as tuberculosis, a careful clinical evaluation and accurate differential diagnosis is more essential than empirical anti-tuberculous medication.

• Radiation Oncology Journal
• /
• v.23 no.3
• /
• pp.169-175
• /
• 2005

Purpose: Although computed tomography (CT) simulators are commonly used in radiation therapy department, many Institution still use conventional CT for treatments. In this study the setup errors that occur during simulation, CT scan (diagnostic CT scanner), and treatment were evaluated for the twenty one breast cancer patients. Materials and Methods: Errors were determined by calculating the differences in isocenter location, SSD, CLD, and locations of surgical clips implanted during surgery. The anatomic structures on simulation film and DRR image were compared to determine the movement of isocenter between simulation and CT scan. The isocetner point determined from the radio-opaque wires placed on patient's surface during CT scan was moved to new position if there was anatomic mismatch between the two images Results: In 7/21 patients, anatomic structures on DRR Image were different from the simulation Image thus new isocenter points were placed for treatment planning. The standard deviations of the diagnostic CT setup errors relative to the simulator setup in lateral, longitudinal, and anterior-posterior directions were 2.3, 1.6, and 1.6 mm, respectively. The average variation and standard deviation of SSD from AP field were 1.9 mm and 2.3 mm and from tangential fields were 2.8 mm and 3.7 mm. The variation of the CLD for the 21 patients ranged from 0 to 6 mm between simulation and DRR and 0 to 5 mm between simulation and treatment. The group systematic errors analyzed based on clip locations were 1.7 mm in lateral direction, 2.1 mm in AP direction, and 1.7 mm in SI direction. Conclusion: These results represent that there was no significant differences when SSD, CLD, clips' locations and isocenter locations were considered. Therefore, it is concluded that when a diagnostic CT scanner is used to acquire an image, the set-up variation is acceptable compared to using CT simulator for the treatment of breast cancer. However, the patient has to be positioned with care during CT scan in order to reduce the setup error between simulation and CT scan.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.6
• /
• pp.1263-1270
• /
• 1997

Background : Differentiation of malignity and benignity is crucial for management of solitary pulmonary nodule(SPN). Clinical parameters such as patient's age, nodule size, smoking history, doubling time, typical calcification in X-ray and CT findings have been reported as helpful in this purpose. However, in most cases, these parameters are not conclusive. Glucose metabolism is increased in cancer tissues including lung cancer tissues. After uptake of 2-[F-18]-fluoro-2-deoxy-D-glucose(FDG), the glucose analogue, by cancer cell, FDG is trapped in the cell without further metabolism after phosphorylation. Thus, hypermetabolic focus in FDG-positron emission tomography (PET) imaging suggest malignancy. We evaluated the diagnostic efficacy of FDG-PET imaging in distinguishing malignant and benign SPN. Methods : We evaluated 28 patients with SPN from Jan. 1995 to Jan. 1997. CT scan of chest and whole-body FDG-PET imaging were performed in all patients. Histologic diagnosis was confirmed by transthoracic fine needle aspiration and biopsy, bronchoscopic biopsy and open thoracotomy. Results : Of the 28 SPN's, 22 nodules were malignant and 6 nodules were benign. FDG-PET imaging diagnosed all malignant nodules correctly as positive, and diagnosed 4 of 6 benign nodules correctly as negative. One tuberculous granuloma and one aspergilloma showed hypennetabolic focus and were diagnosed falsely positve with FDG-PET imaging. In the diagnosis of SPN with FDG-PET, sensitivity and specificity were 100% and 66.7%, positive predictive value and negative predictive value were 92% and 100%. Conclusion : FDG-PET imaging is highly useful noninvasive diagnostic tool in distinguishing between malignant SPN and benign SPN.

• Journal of radiological science and technology
• /
• v.32 no.4
• /
• pp.361-370
• /
• 2009

The image quality management of bone mineral density is the responsibility and duty of radiologists who carry out examinations. However, inaccurate conclusions due to lack of understanding and ignorance regarding the methodology of image quality management can be a fatal error to the patient. Therefore, objective of this paper is to understand proper image quality management and enumerate methods for examiners and patients, thereby ensuring the reliability of bone mineral density exams. The accuracy and precision of bone mineral density measurements must be at the highest level so that actual biological changes can be detected with even slight changes in bone mineral density. Accuracy and precision should be continuously preserved for image quality of machines. Those factors will contribute to ensure the reliability in bone mineral density exams. Proper equipment management or control methods are set with correcting equipment each morning and after image quality management, a phantom, recommended from the manufacturer, is used for ten to twenty-five measurements in search of a mean value with a permissible range of ${\pm}1.5%$ set as standard. There needs to be daily measurement inspections on the phantom or at least inspections three times a week in order to confirm the existence or nonexistence of changes in values in actual bone mineral density. in addition, bone mineral density measurements were evaluated and recorded following the rules of Shewhart control chart. This type of management has to be conducted for the installation and movement of equipment. For the management methods of inspectors, evaluation of the measurement precision was conducted by testing the reproducibility of the exact same figures without any real biological changes occurring during reinspection. Bone mineral density inspection was applied as the measurement method for patients either taking two measurements thirty times or three measurements fifteen times. An important point when taking measurements was after a measurement whether it was the second or third examination, it was required to descend from the table and then reascend. With a 95% confidence level, the precision error produced from the measurement bone mineral figures came to 2.77 times the minimum of the biological bone mineral density change. The value produced can be stated as the least significant change (LSC) and in the case the value is greater, it can be stated as a section of genuine biological change. From the initial inspection to equipment moving and shifter, management must be carried out and continued in order to achieve the effects. The enforcement of proper quality control of radiologists performing bone mineral density inspections which brings about the durability extensions of equipment and accurate results of calculations will help the assurance of reliable inspections.

• Tuberculosis and Respiratory Diseases
• /
• v.66 no.4
• /
• pp.288-294
• /
• 2009

Background: A lung hyperinflation, or air trapping, caused by expiratory flow-limitation contributes to dyspnea in patients with chronic obstructive pulmonary disease (COPD). Forced expiratory volume in 1 second ($FEV_1$) has served as an important diagnostic measurement of COPD, but does not correlate with patient-centered outcomes such as dyspnea. Therefore, this study was performed to investigate the role of radiologic quantity in evaluating the dyspnea in patients with COPD by measuring lung hyperinflation in chest x-ray and high resolution chest tomography (HRCT). Methods: Fifty patients with COPD were enrolled in this study. Their subjective dyspnea score (modified Borg scale dyspnea index), spirometry, and lung volume were measured. Simultaneous hyperinflations of chest x-ray score ("chest score") and degree of emphysema of HRCT ("HRCT score") were measured. The "chest score" were composed of lung length, retrosternal space width, and height of the arc of the diaphragm and "HRCT score" were composed of severity and extent of emphysema. Results: The mean age of patients was 69 years old and their mean $FEV_1$ was 51.7%. The Borg score significantly correlated with parameters of spirometry and lung volume, including FVC, $FEV_1$, $FEV_1$/FVC, RV, RV/TLC, and DLCO. The Borg score correlated well with "HRCT score", but did not correlate with "chest score". Also, the Borg scale correlates inversely with body mass index. Conclusion: The quantity of emphysema on chest HRCT may serve as an objective marker of dyspnea in patients with COPD.