• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.6
• /
• pp.709-715
• /
• 2007

The dewaterability of a sludge can be characterized by two ways: the residual moisture content in the sludge cake after dewatering process, and the filtration of the sludge. Time to filter (TTF) represents filtration processes that are special cases of the flow through a solid matrix concept. TTF characterizes a resistance to filtration. The sludge resistance, in turn, can be subdivided into resistances associated with the solid phase and the liquid phase to evaluate the effect of each of the two phases on sludge dewaterability. In order to determine the dewatering characteristics of the water sludge samples, TTF and zeta potential were measured. For these studies cationic polymer was chosen for water sludge dewatering experiments. The zeta potential of thickener sludges neared from minus values to zero values till 4 days after sampling. The dewaterability of thickener sludges using cationic polymer was deteriorated according to the increase of detention time. As the detention time was increased from 4 to 10 days, the optimal dose of the polymer was increased from 4 to 8mg/L. Therefore, the optimal detention time plays an important part for the dewaterability of a sludge.

• Economic and Environmental Geology
• /
• v.57 no.2
• /
• pp.177-184
• /
• 2024

This study was conducted to find a way to reduce the production of cakes generated in the domestic aggregate production process. Cakes from 8 wet aggregate producers were collected and particle size was analyzed. Samples were collected step by step from an aggregate producer A, particle size analysis was performed, and the material balance was calculated before and after an sand recovery unit by modeling the production process. As a result of the particle size analysis of eight cakes, one sample contained 50% sand, and the rest contained about 5% to 25% sand. The results showing that the cake contained a variety of sand in cakes may indicate that the recovery efficiency of the sand recovery units in the field varied. Sieve analysis of the samples showed that the generation of sand particles increased 2.8 times during the third crushing compared to the second crushing, and more cake particles were generated. As a result of simulating the sand recovery unit model, the lower the cut point of the cyclone and dewatering screen, the higher the sand production and the less cake production appeared. In order to reduce the production of cake in the field, it was determined that an optimal operation of the sand recovery unit was necessary in the aggregate production process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.5
• /
• pp.1098-1107
• /
• 2001

This study is to develop the pretreatment for the excess and digested sludge by elector-coagulation and dewatering. Electrocoagulation is applied to excess and digested sludge before transferring to the pistion type for dewatering. Piston type filter press as a laboratory scale plant was used to estimate the dewaterability. MMD of excess sludge was increased from initial diameter of particles ($34.16{\mu}m$) to the 87%($64.01{\mu}m$) after electrocoagulation. Al electrode is more effective than Fe electrode for the dewaterabiltity of excess sludge Electrodewatering after electrocoagulation as pretreatment makes the water content of sludge cake 50~60 wt%.

• Korean Journal of Food Science and Technology
• /
• v.28 no.4
• /
• pp.638-643
• /
• 1996

The efficiency of dewatering of soybean milk residue was improved by hydraulic pressing after pH adjustment to 4.5 with organic acids such as acetic and lactic acids. Water content of raw soybean milk residue was reduced from 80% to 72% by pressing after pH adjustment, while only to 78% by the conventional hydraulic press. The water content of the residue after pH adjustment was further reduced to 63% by hydraulic pressing with ohmic heating. The pH adjustment facilitated separation of cake from the filter cloth and reduced the solid content of the expressed liquid from 10 to 3%.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.6
• /
• pp.800-808
• /
• 2005

It is required to propose an alternatives for appropriate sludge treatment owing to persistent construction of sewage treatment plant and increase of sewage sludge quantity. In order to treat sludge more efficiently, the methods which reduce the cost of sludge treatment have been studied such as sludge reduction and conditioning. Especially ozone treatment reduces solid quantity and improves separation of solid-liquid at the same time. Therefore ozone treatment have a positive effect on reduction and stabilization of sludge. So, this study applied ozone to sewage sludge and induced cell destruction of sludge. By comparing with the correlation between thickening and dewatering, and evaluating moisture content and solubilization of cake, this study verificates the effect of process improvement for ozone pre-treatment. In J-STP case, according to ozone dose solid flux increased about 12 times from $1kg/m^2{\cdot}h$ to $12kg/m^2{\cdot}h$. Also this plant were capable to shorten thickening time from 40 minutes to 6~7 minutes. Thus it is expected to reduce volume and retention time of thickener. On pH effect factor, dewatering at pH4 was more than at pH11, $3.05{\times}10^{11}$ and $3.82{\times}10^{11}(m/kg)$. But effect of pH was analogous to ozone, $2.81{\times}10^{11}(m/kg)$. The effect of pH on thickening was similar to law sludge, $0.68(kg/m^2{\cdot}h)$, and the effect of ozone injection on thickening was the biggest, $3.45(kg/m^2{\cdot}h)$. The COD solubilization rate improved from about 5 to 30%. So it is judged that we are able to utilize most solubilized sludge to another sewage treatment plants.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.4
• /
• pp.508-514
• /
• 2004

Industrial and municipal wastewater treatment plants produce large amounts of sludge cakes for final disposal. This problem is an inevitable drawback inherent to the activated sludge process. Both the reduction of the amount of sludge produced and improvement of its dewaterability are presently very important issue also in Korea. So many pre-treatment processes have been developed in order to improve sludge dewatering efficiency. In this study the effects of hydrogen peroxide and paper sludge mixing processes were considered as reasonable alternatives to enhance sludge dewaterability. The CST of sludge was significantly decreased, and dewaterability improved by hydrogen peroxide oxidation treatment. The optimum dosage of hydrogen peroxide was proved to be 10mg/g-TS (when TS of sludge was 2%) with the conditions of pH 4 and only 1~2 minutes of reaction time. The mixing of paper sludge with sewage sludge was turned out to be very effective in reduction of sludge cake; 30% of sludge cake reduction was accomplished. Optimum mixing ratio of paper sludge was about 30%(v/v). This process also could save 25% of polymer to be required. These two alternatives are somewhat realistic, but it was concluded that paper sludge mixing process will be the best choice.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.1
• /
• pp.123-130
• /
• 2007

The effects of hydrogen peroxide treatment on the reduction of waterworks sludge were investigated in this study. Sludge treated by peroxidation $H_2O_2$ oxidation) was dewatered using a pressure filter at 3atm. It was observed that $H_2O_2$ treatment at the acidic condition significantly reduce both cake water content and specific resistance to filtration (SRF), indicating the enhancement of dewaterability and filterability. The filterability by hydrogen peroxide treatment at pH 3.5 was better than acidic treatment and became comparable with polymer conditioning. The sludge filterability evaluated by SRF was optimal at a dose 2ml $H_2O_2$/sludge($0.02g\;H_2O_2/gTS$) after adjusting of pH to 3.5. The $H_2O_2$ oxidation at pH 3.5 also produced even more dewatered cake when compared with polymer conditioning. The reduction rate of sludge mass at an optimal condition showed 34% compared with untreated sludge. The effects of peroxidation on sludge properties including zeta potential, bound water and particle size were also evaluated. Peroxidation at the acidic condition reduced both bound water and zeta potential. By $H_2O_2$ combined with sulfuric acid leached iron caused Fenton's reaction, which showed a potential to significantly reduce the amount of solids mass and to produce more compact cake with higher filterability.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.2 no.1
• /
• pp.87-98
• /
• 1994

Sludge minimization in an water treatment plant can be achieved by optimizing a main water treatment process as well as by enhancing a thickening and a dewatering facilities. In this study, dewatering and drying techniques for reducing the quantity of the water sludge generated from the conventional water treatment plant in the local states were investigated by reducing its water content. Not only the types and dosages of polymers but also the mixing intensity of the mixtures of a concentrated sludge and polymers on the different pH were evaluated for the optimum dewatering conditions of the water sludge. Weight reduction of the water sludge was also tested at a given temperature range. The dewatering efficiency of the water sludge was not affected by the types of polymer but by mixing intensity(GT value) in this study. pH effect on dewaterbility of the water sludge took a major role at the neutral pH range. The optimal polymer dose was 1.5 mg-polymer/g-TSS(about 40mg/L as polymer). Dewaterability was enhanced at a lower mixing intensity(GTbelow 10,000 sec-1). Free water in the void of sludge cake was dried around $100^{\circ}C$, chemical bound water was evaporated around $320^{\circ}C$, and organic material was burned out at the range of 300 to $600^{\circ}C$. Ignition losses of the water sludge were varied 15 to 40 % as the raw water quality. The ignition loss due to the chemical bound water was 10-20% and the loss due to the organic material was 4-20% of the total ignition loss.

• Korean Journal of Food Science and Technology
• /
• v.28 no.2
• /
• pp.324-329
• /
• 1996

In order to develop a novel dewatering process for soybean milk residue, hydraulic press with ohmic heating was built and its expression conditions were examined. The electric conductivity of raw soybean milk residue was 0.128 S/m and increased linearly with increasing temperature. Water content of the residue could be reduced to 74% with the conventional hydraulic press, but to less than 70% by applying ohmic heating to the hydraulic press. The most effective dewatering was achieved by applying alternative current with 5 kHz frequency at 60 V during expression. The solid content of the expressed liauid was markedly reduced from 10% to 3.3% by ohmic heating during expression. Temperature of the cake rose to above $95^{\circ}C$ during the dewatering due to ohmic heating.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.1
• /
• pp.3-9
• /
• 1990

Expression is on operation of separating liquid from solid liquid mixtures which has long been used on a universal scale in widely divergent fields. In fruit pulps processing and fermentation industries. removal of a portion of the liquid in filler cake is essential to the maximum yields of products. In sewage sludge treatments, dewatering of filter cakes is important to disposal by incineration. transportation. and landfill. In the chemical process industries, drying of wet cakes increases cost, and it is desirable to eliminate as much liquor as possible by non-thermal methods. This paper is mainly concerned with the development of a simplified equation for constant-pressure expression.