• Nuclear Engineering and Technology
• /
• 제56권1호
• /
• pp.9-18
• /
• 2024

In-vessel retention through external reactor vessel cooling (IVR-ERVC) is a severe accident management (SAM) strategy that has been adopted and used in many nuclear reactors such as AP1000, APR1400, and light water reactor etc. Some reactor accidents have raised concerns about nuclear reactors among residents, leading to a decrease in residents' acceptability and many studies on SAM are being conducted. Experiments on IVR-ERVC are almost impossible due to its specificity, so fluid characteristics are analyzed through BALI experiments with similar condition. In this study, computational fluid dynamics (CFD) via Reynolds-averaged Navier-Stokes (RANS) and large eddy simulation (LES) for BALI experiments were performed. Steady-state CFD analysis was performed on three turbulence models, and SST k-ω model was in good agreement with the experimental measurement temperature within the maximum error range of 1.9%. LES CFD analysis was performed based on the RANS analysis results and it was confirmed that the temperature and wall heat flux for depth was consistent within an error range of 1.0% with BALI experiment. The LES CFD analysis results were compared with those of the Lagrangian-based solver. LES matched the temperature distribution better than SOPHIA, but SOPHIA calculated the position of boundary between stratified layer and convective layer more accurately. On the other hand, Lagrangian-based solver predicted several small eddy behaviors of the convective layer and LES predicted large vortex behavior. The vibration characteristics near the cooling part of the BALI experimental device were confirmed through Fast Fourier Transform (FFT) investigation. It was found that the power spectral density for pressure at least 10 times higher near the side cooling than near the top cooling.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• 제40권3호
• /
• pp.206-213
• /
• 2004

As far as an opening device of fishing gears is concerned, applications of a kite are under development around the world. The typical examples are found in the opening device of the stow net on anchor and the buoyancy material of the trawl. While the stow net on anchor has proved its capability for the past 20 years, the trawl has not been wildly used since it has been first introduced for the commercial use only without sufficient studies and thus has revealed many drawbacks. Therefore, the fundamental hydrodynamics of the kite itself need to ne studied further. Models of plate and canvas kite were deployed in the circulating water tank for the mechanical test. For this situation lift and drag tests were performed considering a change in the shape of objects, which resulted in a different aspect ratio of rectangle and trapezoid. The results obtained from the above approaches are summarized as follows, where aspect ratio, attack angle, lift coefficient and maximum lift coefficient are denoted as A, B, $C_L$ and $C_{Lmax}$ respectively : 1. Given the triangular plate, $C_{Lmax}$ was produced as 1.26${\sim}$1.32 with A${\leq}$1 and 38$^{\circ}$B${\leq}$42$^{\circ}$. And when A${\geq}$1.5 and 20$^{\circ}$${\leq}$B${\leq}$50$^{\circ}$, $C_L$ was around 0.85. Given the inverted triangular plate, $C_{Lmax}$ was 1.46${\sim}$1.56 with A${\leq}$1 and 36$^{\circ}$B${\leq}$38$^{\circ}$. And When A${\geq}$1.5 and 22$^{\circ}$B${\leq}$26$^{\circ}$, $C_{Lmax}$ was 1.05${\sim}$1.21. Given the triangular kite, $C_{Lmax}$ was produced as 1.67${\sim}$1.77 with A${\leq}$1 and 46$^{\circ}$B${\leq}$48$^{\circ}$. And when A${\geq}$1.5 and 20$^{\circ}$B${\leq}$50$^{\circ}$, $C_L$ was around 1.10. Given the inverted triangular kite, $C_{Lmax}$ was 1.44${\sim}$1.68 with A${\leq}$1 and 28$^{\circ}$B${\leq}$32$^{\circ}$. And when A${\geq}$1.5 and 18$^{\circ}$B${\leq}$24$^{\circ}$, $C_{Lmax}$ was 1.03${\sim}$1.18. 2. For a model with A=1/2, an increase in B caused an increase in $C_L$ until $C_L$ has reached the maximum. Then there was a tendency of a very gradual decrease or no change in the value of $C_L$. For a model with A=2/3, the tendency of $C_L$ was similar to the case of a model with A=1/2. For a model with A=1, an increase in B caused an increase in $C_L$ until $C_L$ has reached the maximum. And the tendency of $C_L$ didn't change dramatically. For a model with A=1.5, the tendency of $C_L$ as a function of B was changed very small as 0.75${\sim}$1.22 with 20$^{\circ}$B${\leq}$50$^{\circ}$. For a model with A=2, the tendency of $C_L$ as a function of B was almost the same in the triangular model. There was no considerable change in the models with 20$^{\circ}$B${\leq}$50$^{\circ}$. 3. The inverted model's $C_L$ as a function of increase of B reached the maximum rapidly, then decreased gradually compared to the non-inverted models. Others were decreased dramatically. 4. The action point of dynamic pressure in accordance with the attack angle was close to the rear area of the model with small attack angle, and with large attack angle, the action point was close to the front part of the model. 5. There was camber vertex in the position in which the fluid pressure was generated, and the triangular canvas had large value of camber vertex when the aspect ratio was high, while the inverted triangular canvas was versa. 6. All canvas kite had larger camber ratio when the aspect ratio was high, and the triangular canvas had larger one when the attack angle was high, while the inverted triangluar canvas was versa.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• 제7권6호
• /
• pp.12-20
• /
• 2008

Recent wireless communication technologies are envisioned as an innovative alternative to solve transportation problems. On ad hoc networks, as a wireless communication technology, nodes can communicate data without any infrastructure. In particular, vehicular ad hoc networks (VANETs), a specific ad hoc network applied to vehicles, enable vehicles equipped with a communication device to form decentralized traffic information systems in which vehicles share traffic information they experienced. This study investigated traffic information dissemination in a VANET-based traffic information system. For this study, an integrated transportation and communications simulation framework was developed, and experiments were conducted with real highway networks and traffic demands. The results showed that it took 3 minutes in the low traffic density situations (10 vehicle/lane.km) and 43 seconds in the high traffic density condition (40 vehicle/lane.km) to deliver traffic information of 5km away with 10% market penetration rate. In uncongested traffic conditions, information seems to be disseminated via equipped vehicles in the opposite direction. In congested traffic conditions, the sufficient availability of equipped vehicles traveling in the same direction reduces the chance to use vehicles in the opposing direction even though it is still possible.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.187-205
• /
• 2014

The global price of oil, which is both finite and limited in quantity, has been rising steadily because of the increasing requirements for energy in both developing and developed countries. Furthermore, regulations have been strengthened across all industries to address global warming. Many studies of hull resistance, propulsion and operation of ships have been performed to reduce fuel consumption and emissions. This study examined the design parameters of the propeller boss cap fin (PBCF) and hub cap for 6,000TEU container ships to improve the propulsion efficiency. The design parameters of PBCF have been selected based on the geometrical shape. Computational fluid dynamics (CFD) analysis with a propeller open water (POW) test was performed to check the validity of CFD analysis. The design of experiment (DOE) case was selected as a full factorial design, and the experiment was analyzed by POW and CFD analysis. Analysis of variance (ANOVA) was performed to determine the correlation among design parameters. Four design alternatives of PBCF were selected from the DOE. The shape of a propeller hub cap was selected as a divergent shape, and the divergent angle was determined by the DOE. Four design alternatives of PBCF were attached to the divergent hub cap, and the POW was estimated by CFD. As a result, the divergent hub cap with PBCF has a negative effect on the POW, which is induced by an increase in torque coefficient. A POW test and cavitation test were performed with a divergent hub cap with PBCF to verify the CFD result. The POW test result showed that the open water efficiency was increased approximately 2% with a divergent hub cap compared to a normal cap. The POW test result was similar to the CFD result, and the divergent hub cap with the PBCF models showed lower open water efficiency. This was attributed to an increase in the torque coefficient just like the CFD results. A cavitation test was performed using the 2 models selected. The test result showed that the hub vortex is increased downstream of the propeller.

• The Journal of the Korea institute of electronic communication sciences
• /
• 제9권8호
• /
• pp.927-938
• /
• 2014

A number of crime and disease relief situation show a clear increasing trend in domestic and overseas country. In particular, we desperately need a fast location information sharing with high accuracy for dealing with this situation efficiently. In this paper, we propose a DGPS framework and performance evaluation based on Web service enable increase location accuracy using low-cost GPS or AGPS. The framework consists of mobile station to realize the final service by receiving the correction values that are created in the base station closest to the current position from DGPS server, base station system to transmit the correct values to DPGS server by installing at base point and DGPS framework working at DGPS server. Our framework is fundamentally designed to respond based on XML to service request. In addition, for performance evaluation, we make use of 3 sites of Level 2 city base-station among the base stations being operated in Suncheon-si. Through performance evaluation, we show that our framework outperforms about 10%~15% in terms of error improvement rate, compared with the existing schemes. And we have the advantage that various services can be expanded owing to receiving the correction values through mobile device such as, smart phone, smart pad, net-book by using XML based Web services.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제13권4호
• /
• pp.195-206
• /
• 1980

Fish were grown in a water recycling rearing system consisting of a filter system, of which the area is about $30\;m^2$ and the volume of filter gravels is about $15\;m^3$, 6 rearing and 2 supplementary tans about $7\;m^2$ of surface area each. The results for 180 days from April 18 to October 14,1980 are summarized as following: One rearing tank was used for main experiment stocked with an equal number, and weight of each Israeli strain and $F_1$, hybrid between this strain and Korean local strain of common carp. Gross total production was 461 kg with a net production of 395 kg, and the Israeli strain grew to about 8 times initial weight and the hybrid about 6 times. Based on an analysis of results of the above mentioned main experiment and the other miscellaneous fish grown in the remaining tanks, it was considered to be feasible to implement a commercial production in this system by improving parts of the system and adding a number of the units. A special problem seems to be an adoption of more effective aeration device when fish loading increases. A solid waste removal system was deviced by use of by-pass flow ana this system worked very efficiently in view of supply water economy. A serious problem encountered in this experiment was heavy outbreaks of the gill-fluke, Dactylogyrus sp. which was relatively easily eradicated with Dipterex or DDVP treatment in the first trials, but later on strains which were resistant to any of these chemicals appeared.

• Journal of the Korean Society for information Management
• /
• 제31권3호
• /
• pp.29-63
• /
• 2014

This study attempted to reveal the characteristics of the Y generation, to derive the services of the next generation digital library, and to compare differences between the demands of the baby boom generation and the Y generation to some extent. As a result, first, it is shown that the digital device the Y generation uses the most, was a cell phone or smartphone, followed by desktop PC, notebook PC, and digital camera. Although there were some differences, the Y generation's use ratio of digital devices was substantially similar to the baby boomers'. Second, there was a significant difference between the Y generation and baby boom generation in terms of using digital services. While the Y generation used internet portals the most, the baby boom generation used e-mail service the most. Third, we surveyed the services which the Y generation and baby boom generation require for the next generation digital libraries, by grouping as follows: the cloud service, infinite creative space (maker space), big data, augmented reality, Google Glass, context-aware technologies, semantic services, SNS service, digital textbook service, RFID and QRCode service, library space configuration, a state-of-the-art display technology, and other innovative services. While the most demanded service by the Y generation was big data service, the baby boom generation most demanded digital textbook service.

• Journal of KIISE:Computing Practices and Letters
• /
• 제14권9호
• /
• pp.916-920
• /
• 2008

The personal workspace consists of user- specified computing environment such as user profile, applications and their configurations, and user data. Mobile computing devices (i.e., cellular phones, PDAs, laptop computers, and Ultra Mobile PC) are getting smaller and lighter to provide personal work-space ubiquitously. However, various personal work-space mobility solutions (c.f. VMWare Pocket ACE[1], Mojopac[2], u-PC[3], etc.) are appeared with the advance of virtualization technology and portable storage technology. The personal workspace can be loaded at public PC using above solutions. Especially, we proposed a framework called ubiquitous personal computing environment (u-PC) that supports mobility of personal workspace based on wireless iSCSI network storage in our previous work. However, previous u-PC could support limited applications, because it uses IRP (I/O Request Packet) forwarding technique at filter driver level on Windows operating system. In this paper, we implement OS-level virtualization technology using system call hooking on Windows operating system. It supports personal workspace mobility and covers previous u-PC limitation. Also, it overcomes personal workspace loading overhead that is limitation of other solutions (i.e., VMWare Pocket ACE, Mojopac, etc). We implement a prototype consisting of Windows XP-based host PC and Linux-based mobile device connected via WiNET protocol of UWB. We leverage several use~case models of our framework for proving its usability.

• Nuclear Engineering and Technology
• /
• 제40권6호
• /
• pp.451-458
• /
• 2008

After more than 10 years construction, KSTAR (Korea Superconducting Tokamak Advanced Research) had finally completed its assembly in June 2007, and then achieved the goal of first-plasma in July 2008 through the four month's commissioning. KSTAR was constructed with fully superconducting magnets with material of $Nb_3Sn$ and NbTi, and their operation temperatures are maintained below 4.5K by the help of Helium Refrigerator System. During the first-plasma operation, plasmas of maximum current of 133kA and maximum pulse width of 865ms were obtained. The KSTAR Integrated Control System (KICS) has successfully fulfilled its missions of surveillance, device operation, machine protection interlock, and data acquisition and management. These and more were all KSTAR commissioning requirements. For reliable and safe operation of KSTAR, 17 local control systems were developed. Those systems must be integrated into the logically single control system, and operate regardless of their platforms and location installed. In order to meet these requirements, KICS was developed as a network-based distributed system and adopted a new framework, named as EPICS (Experimental Physics and Industrial Control System). Also, KICS has some features in KSTAR operation. It performs not only 24 hour continuous plant operation, but the shot-based real-time feedback control by exchanging the initiatives of operation between a central controller and a plasma control system in accordance with the operation sequence. For the diagnosis and analysis of plasma, 11 types of diagnostic system were implemented in KSTAR, and the acquired data from them were archived using MDSpius (Model Driven System), which is widely used in data management of fusion control systems. This paper will cover the design and implementation of the KSTAR integrated control system and the data management and visualization systems. Commissioning results will be introduced in brief.

• Journal of the Korean Institute of Gas
• /
• 제18권4호
• /
• pp.13-20
• /
• 2014

In natural gas distribution system, gas pressure is regulated correspond to requirement using throttle valve which is releasing huge pressure energy as useless form. The waste pressure can be recovered by using turbo machinery devices such as a turbo expander. In this process, excessive temperature drop occurs due to Joule-Thompson effect during the expansion process. Installing natural gas boiler before or after the turbo expander prevents temperature drop. Fuel cell or gas engine hybrid system further improve the efficiency, but 1~2% of total transporting natural gas is used for operating the hybrid system. In this study, a heat pump system is proposed as a preheating device which can be operated without using transporting natural gas. Thermodynamic analysis on evaporating and condensing temperatures and refrigerants is conducted. Results show that R717 is proper refrigerant for the hybrid system with high COP and low turbine work within the defined operating conditions. In domestic usage in Korea, the heat pump system has more economic feasibility owing to natural gas being imported with a high price of LNG form.