• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.80-83
• /
• 2004

The FRP plate or sheet bonding technology was widely used for strengthening deficient RC structures. The strengthened structure using FRP bonding scheme, however, experience the complex interfacial behaviour which is difficult to predict. Therefore, the unbonded scheme using some anchorage device can be is an alternative for more reliable design. In this study, wedge-type anchor for FRP plate is developed for the unbonded flexural strengthening scheme. Some parameter study using 2D finite element method is performed. The analysis parameters are taken as wedge-guide friction coefficients, wedge- FRP ,.friction coefficient and wedge inclination angle. Based on the parameter study, more efficient anchors are designed and tested. The test result show that the developed anchor assure about $80\%$ FRP strength, which is higher performance than typical bonding scheme. Last, 3D finite element analysis is performed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1519-1522
• /
• 1996

In this paper, we have developed a tele-robotic system for nozzle dam installation/removal works and tube relating maintenance works inside unclear power plant steam generator. Developed tele-robotic system consists of many hardwares including robot and a control system. Based on the 3 dimensional graphic simulation, a 6 D.O.F. hydraulic actuated robot and a 2 D.O.F. robot install/removal device have been developed. And also we deviced special tools for nozzle dam carry and bolting. For the tele-robot and other devices to be controlled at the nonradioactive area outside reactor containment building, we developed a tele-robot control system consisting of supervisory controller and remote controller.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.232-234
• /
• 2000

Double-side LPM may be replaced the solenoid as the valve driving device with out difficulty and give full play to control the valve accurately. Double-side LPM's magnetic structure is so complex by the cubic effect configuration that finite element analysis is required. Thus, in this paper, by 2D and 3D finite element analysis, we get the flux distribution and static thrust force curves of designed double side LPM.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.2
• /
• pp.185-194
• /
• 2008

In this paper, an efficient technique is proposed to integrate the 3D user interface with the tiled display system in PC cluster environment. In the developed 3D user interface software, various menus are provided to increase the user friendliness of the interface, including the several model-control-commands. To eliminate the noise produced from the 3D user interface devices, the box filtering algorithm is employed. Further, a communication splitting algorithm, which is a kind of asynchronous communication method, is proposed to reduce the motion delay between the 3D interface and the tiled display system, and its efficiency is validated through the benchmarking tests.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2175-2178
• /
• 2005

Selective Laser Sintering(SLS) method is one of Rapid Prototyping(RP) technologies. It has been used to fabricate desirable part to sinter powder and stack the fabricated layer. Since the sintering process occurs using infrared laser having high thermal energy, shrinkage and curling of the fabricated part occurs according to thermal distribution. Therefore, the fast scanning path generation is necessary to eliminate the factors of quality deterioration. In case of fabricating larger size parts, the unique scanning device and scanning path generation should be considered. In this paper, the development of SLS machines being capable of large size fabrication(800${\times}$1000${\times}$800 mm, W${\times}$D${\times}$H) will be addressed. The dual laser system and the unique scanning device have been designed and built, which employ CO2 lasers and dynamic 3-axis scanners. The developed system allows scanning a larger planar surface with the desired laser spot size. Also, to generate the fast scanning paths, adaptive path generation is needed with respect to the shape of each layer, and not simply x, y scanning, but the scanning of arbitrary direction should be enabled. To evaluate the suggested method, the complex part will be used for the experiment fabrication.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.6
• /
• pp.462-469
• /
• 2014

After drilling operations at the offshore plant, crude oil is producted under high pressure. After that time, oil recovery is reduced, because the pressure of the pipe inside is low during the secondary produce. At that time injection sea water at the pipe inside through water injection pump that the device increase to recovery. A variety of mathematical analysis during the detailed design analysis was not made through the dynamics characteristic at the domestic company. 2D model has reliability of analysis results for the uncomplicated model. Also element and the node the number of significantly less than in the 3D model. So, the temporal part is very effective. In addition, depending on the quality of mesh 3D is a real model and FEM model occurs error. So, user needs a lot of skill. In this paper, a 2D finite element analysis was performed through the dynamics analysis and the study model was validated.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.67-74
• /
• 2009

In this paper, the multi-band antenna with CPWG(Coplanar Waveguide with Ground) feed for telematics mobile devices is designed and fabricated. The proposed antenna improves the return loss characteristic by using open-circuited stub matching and rectangular slot in the radiation patch. In addition, CPWG structure makes up for the drawback of the CPW which is variation of impedance matching according to the gap variation of the feed line and the ground. The fabricated antenna has 1.4GHz ($1.43GHz{\sim}2.83GHz$, 65%) band width on -10dB (VSWR<2) and the maximum gains are 0.8dBi, 1.34dBi, 2.41dBi, 2.53dBi, 2.6dBi and 1.51dBi on each resonant frequency that are GPS $(1.564GHz{\sim}1.585GHz)$, PCS/DCS $(1.710GHz{\sim}1.984GHz)$, WCDMA $(2.170GHz{\sim}2300GHz)$, Bluetooth/Wi-Fi/WLAN $(2.4GHz{\sim}2.483GHz)$, WiBro $(2.3GHz{\sim}2.4GHz)$, SDMB $(2.605GHz{\sim}2.655GHz)$. It also has an omni-directional radiation pattern of H-Plane.

• Journal of Navigation and Port Research
• /
• v.27 no.2
• /
• pp.217-221
• /
• 2003

In this work, we used a novel RF-CSP to develop a broadband amplifier MMIC, including all the matching and biasing components, for Ku and K band applications. By utilizing an ACF for the RF-CSP, the fabrication process for the packaged amplifier MMIC could be simplified and made cost effective. STO (SrTiO$_3$) capacitors were employed to integrate the DC biasing components on the MMIC. A pre-matching technique was used for the gate input and drain output of the FETs to achieve a broadband design for the amplifier MMIC. The amplifier CSP MMIC exhibited good RF performance (Gain of 12.5$\pm$1.5 dB, return loss less than -6 dB, PldB of 18.5$\pm$1.5 dBm) over a wide frequency range. This work is the first report of a fully integrated CSP amplifier MMIC successfully operating in the Ku/K band.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.175-180
• /
• 2006

A single sideband(SSB) modulator operating at 5.5 GHz was fabricated by polarization inversion techniques. The dimension of domain inversion in a $LiINbO_3$ Mach-Zehnder structure was precisely controlled so that the RF signal applied on two Mach-Zehnder arms gives rise to $90^{\circ}$ effective phase difference. The single sideband suppression was maximized by optimization of the polarization status of the optical input and by the DC bias value. The fabricated device showed the center frequency of 5.8 GHz and the maximum sideband suppression of 33dB, where the bandwidth of 15 dB sideband suppression ranged over a 2.5 GHz span. The optical phase delay could be regulated by the DC bias voltage, fur example, the enhanced optical modulation sideband was distinctively switched from the upper sideband to the lower sideband by changing the DC bias voltage from 1.9 V to -10.6 V.

• The Journal of Korean Physical Therapy
• /
• v.34 no.5
• /
• pp.278-281
• /
• 2022

Purpose: This study sought to compare the muscle activity of the deltoid muscle according to the range of motion during the proprioceptive neuromuscular facilitation (PNF) upper extremity D2 pattern exercise performed with an isokinetic exercise device. The aim was to provide basic data for selecting an exercise for the relevant segment of the range of motion to enhance function in clinical practice. Methods: In this study, the relevant measurements of the anterior and middle trapezius of 25 healthy adults were taken using a surface electromyography system. The upper extremity pattern exercise was performed in three ranges (0% to 50%, 50% to 100%, and 25% to 75%) using the upper extremity isokinetic device. Results: There was a statistically significant difference in the muscle activity ratios of the anterior and middle deltoid muscles according to the measurement conditions (p<0.05). There was a statistically significant difference in the activity ratio of the middle deltoid muscle according to the measurement conditions in the ratio from the start range to the end range (p<0.05). There was no significant difference in the muscle onset time difference according to the measurement conditions (p>0.05). Conclusion: The muscle activity of the anterior and middle deltoid muscles was analyzed according to the range of motion during the PNF upper extremity pattern exercise performed with an isokinetic device. The results could be used as a basis for selecting exercises for the relevant segment of the range of motion according to the function to be emphasized.