• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.39-44
• /
• 2021

In this paper, two types of BPF(Band Pass Filter) which are hair-pin and interdigital have been designed for millimeter-wave application using two types of material which are LCP(Liquid Crystal Polymer) and PTFE(Polytetrafluoroethylene) and also, their performances such as bandwidth, insertion loss, and in-band flatness are compared. The proposed BPF are designed as third-order filters, and their pass band is from 26.5 GHz to 27.3 GHz. Interdigital BPF using PTFE substrate has most wide -3 dB S21 bandwidth of 7.8 GHz and hair-pin BPF using LCP substrate has most narrow -3 dB S21 bandwidth among the proposed four BPF. For in-band insertion loss, hair-pin BPF using PTFE substrate achieves low insertion loss better than -0.667 dB, and hair-pin BPF using LCP substrate exhibits relatively high insertion loss among the proposed four BPF better than -0.937 dB. However, the maximum difference in insertion loss performance among the proposed four BPF is 0.27 dB, which is too small to negligible. For in-band flatness, interdigital BPF using PTFE substrate shows greatest performance of 0.017 dB, and hair-pin BPF using LCP substrate exhibits the lowest performance of 0.07 dB. There are tiny difference in in-band flatness performance of 0.053 dB. As a results, it is considered that the BPF using LCP substrate can derive the performances similar to that of the BPF using PTFE substrate in Millimeter-wave band.

• The Journal of Korean Society for Radiation Therapy
• /
• v.16 no.1
• /
• pp.57-65
• /
• 2004

Introduction : The phantom that includes high density materials such as steel was custom-made to fix lung and bone in order to evaluation inhomogeneity correction at the time of conducting radiation therapy to treat lung cancer. Using this, values resulting from the inhomogeneous correction algorithm are compared on the 2 and 3 dimensional radiation therapy planning systems. Moreover, change in dose calculation was evaluated according to inhomogeneous by comparing with the actual measurement. Materials and Methods : As for the image acquisition, inhomogeneous correction phantom(Pig's vertebra, steel(8.21g/cm3), cork(0.23 g/cm3)) that was custom-made and the CT(Volume zoom, Siemens, Germany) were used. As for the radiation therapy planning system, Marks Plan(2D) and XiO(CMS, USA, 3D) were used. To compare with the measurement value, linear accelerator(CL/1800, Varian, USA) and ion chamber were used. Image, obtained from the CT was used to obtain point dose and dose distribution from the region of interest (ROI) while on the radiation therapy planning device. After measurement was conducted under the same conditions, value on the treatment planning device and measured value were subjected to comparison and analysis. And difference between the resulting for the evaluation on the use (or non-use) of inhomogeneity correction algorithm, and diverse inhomogeneity correction algorithm that is included in the radiation therapy planning device was compared as well. Results : As result of comparing the results of measurement value on the region of interest within the inhomogeneity correction phantom and the value that resulted from the homogeneous and inhomogeneous correction, gained from the therapy planning device, margin of error of the measurement value and inhomogeneous correction value at the location 1 of the lung showed $0.8\%$ on 2D and $0.5\%$ on 3D. Margin of error of the measurement value and inhomogeneous correction value at the location 1 of the steel showed $12\%$ on 2D and $5\%$ on 3D, however, it is possible to see that the value that is not correction and the margin of error of the measurement value stand at $16\%$ and $14\%$, respectively. Moreover, values of the 3D showed lower margin of error compared to 2D. Conclusion : Revision according to the density of tissue must be executed during radiation therapy planning. To ensure a more accurate planning, use of 3D planning system is recommended more so than the 2D Planning system to ensure a more accurate revision on the therapy plan. Moreover, 3D Planning system needs to select and use the most accurate and appropriate inhomogeneous correction algorithm through actual measurement. In addition, comparison and analysis through TLD or film dosimetry are needed.

• Archives of design research
• /
• v.15 no.1
• /
• pp.49-58
• /
• 2002

Advances in computer technology have made it possible for educators to design and develop their own multimedia instructional materials using visuals such as animation. Although, it generally believed that the Mew attribute of computer animation facilitates student's foaming, there is still relatively little research regarding the way in which student benefit from multimedia instruction using 3-D animation. The purpose of this research was to examine and determine whether the use of 3-D computer generated images is an effective teaching device for hoping children to understand color theory, and enhancing the tractional methods. In this study, a 3-D computer generated presentation was creative and it demonstrated the mixing of primary color to obtain secondary color. Three research hypotheses were developed in this research. The first hypothesis stated that 3-D computer generated presentation will be an effective device for teaching color theory. The second was that the presentation will be eye-catching and it will hold the children's attention. The third was presentation would enhance the children's memory of color. Results of this study show that visualization technology and the use of 3-D graphics ends can be employed in the field of art education to increases a chi1d's understanding of color theory. Also, it was proved that teaching children through 3-D graphic is an highly effective teaching tool. Thus this research is a oontribution to both children's au education and the relatively new field of computer animation.

• The KIPS Transactions:PartD
• /
• v.15D no.5
• /
• pp.609-620
• /
• 2008

The service handling the map data in the mobile device including navigation, LBS, Telematics, and etc., becomes various. The size of map data which is stored and managed in the mobile device is growing and reaches in several GB. The conventional navigation system has used the read-only PSF (physical storage format) in order to enhance the performance of system by maximum in the mobile device which has limited resources. So though a little part of the map data is changed the whole data must be updated. In general, it takes several ten minutes to write the 2 GB map data to a flash memory of mobile device. Therefore, we have developed the mobile spatial DBMS (database management system) to solve the problem which is that the partial map data couldn't be updated in the conventional navigation system. And we suggest the policy to guarantee the performance of the navigation system which is implemented using the spatial mobile DBMS and verify this by experiment.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.33-37
• /
• 2003

A low-power $1{\times}2$ polymeric thermo-optic switch with a trench structure is proposed and fabricated. The trench structure in the optimized region slows down the heat flow from the electrodes, which contributes to the reduction of power consumption. The temperature distribution in the polymer layers has been adjusted to increase the temperature gradient between the two arms of the Y-branch. For comparison, a $1{\times}2$ polymeric thermo-optic switch with no trench structure is fabricated together on the same substrate. In the device with a trench structure, the measured crosstalk is less than -17.0 dB for TE polarization.-15.0 dB for TM polarization. The power consumption is about 66 mW, which is 25% less than that of the device with no trench structure.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.4
• /
• pp.14-23
• /
• 2011

In this paper, a 7-bit 2GSPS folding/interpolation A/D Converter(ADC) with a Self-Calibrated Vector Generator is proposed. The ADC structure is based on a folding/interpolation architecture whose folding/interpolation rate is 4 and 8, respectively. A cascaded preprocessing block is not only used in order to drive the high input signal frequency, but the resistive interpolation is also used to reduce the power consumption. Based on a novel self-calibrated vector generator, further, offset errors due to device mismatch, parasitic resistors. and parasitic capacitance can be reduced. The chip has been fabricated with a 1.2V 0.13um 1-poly 7-metal CMOS technology. The effective chip area including the calibration circuit is 2.5$mm^2$. SNDR is about 39.49dB when the input frequency is 9MHz at 2GHz sampling frequency. The SNDR is improved by 3dB with the calibration circuit.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.2
• /
• pp.250-254
• /
• 2003

A film bulk acoustic resonator (FBAR) device for 2 GHz radio frequency (RF) bandpass filter application is presented. This FBAR device consists of an aluminum nitride (AlN) film sandwiched between top(Al) and bottom(Au) electrodes and an acoustic multilayer reflector of a silicon dioxide/tungsten (SiO2/W). The A/N film deposited using a RF sputtering was observed to have small columnar grains with a strongly preferred orientation towards c axis. In addition to a high quality factor (4300), a large return loss of 37.19 dB was obtained.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.1
• /
• pp.1-10
• /
• 2003

Device characteristics of the Metal-Ferroclecric-Semiconductor FET(MFSFET) are simulated in this study. The field-dependent polarization model and the square-law FET model are employed in our simulation. C-V$_{G}$ curves generated from our MFSFET simulation exhibit the accumulation, the depletion and the inversion regions clearly. The capacitance, the subthreshold and the drain current characteristics as a function of gate bias exhibit the memory windows are 1 and 2 V, when the coercive voltages of ferroelectric are 0.5 and 1 V respectively. I$_{D}$-V$_{D}$ curves are composed of the triode and the saturation regions. The difference of saturation drain currents of the MFSFET device at the dual threshold voltages in I$_{D}$-V$_{D}$ curve is 1.5, 2.7, 4.0, and 5.7 ㎃, when the gate biases are 0, 0.1, 0.2 and 0.3V respectively. As the drain current is demonstrated after time delay, PLZT(10/30/70) thin film shows excellent reliability as well as the decrease of saturation current is about 18 % after 10 years. Our simulation model is expected to be very useful in the estimation of the behaviour of MFSFET devices.T devices.

• Information and Communications Magazine
• /
• v.30 no.7
• /
• pp.58-62
• /
• 2013

최근에 ICT 기반의 융합 서비스 분야로 인구 밀집지역인 메가 시티에서의 교통, 전력, 상/하수도, u-헬스, 안전/보안등의 문제들을 근본적으로 해결하기 위하여 ICT기반 개방형 플랫폼을 이용한 서비스 인프라 구축 및 개선을 위한 연구들이 많이 진행되고 있다. 이러한 ICT 기반의 융합 인프라 구축 서비스들은 M2M(Machine to Machine)과 D2D(Device to Device)를 기본 연결 수단으로 사용하고 있으며, 이들을 기반으로 서비스 정보 전달 및 제어 정보를 실시간으로 처리하기 위한 IP 기반의 플랫폼이 지원되어야만 융합 서비스가 지속적으로 제공 가능할 것이다. 이들 융합서비스 중에서 전력과 관련하여 한국의 스마트그리드 사업은 기후 변화 대응을 위하여CO2 배출을 줄이고, 에너지 효율을 향상하여 새로운 비즈니스 모델을 만들어 일자리와 신산업을 창출하기 위한 국가 프로젝트로 진행되었다. 그러나, 현재의 전력관련 국내 상황을 살펴보면 여름철과 겨울철에 반복적인 전력 수급 불안으로 인해 피크 전력에 대한 예비력이 부족하여 국가적인 재난인 블랙 아웃의 위기를 걱정하고 있는 실정이다. 본고에서는 한국의 스마트그리드 제주실증단지 사업과 관련하여 현황 및 개선 사항들을 알아보고, 향후 거점지구와 국가 단위의 서비스 확장을 위하여ICT 기반의 개방형 인프라 플랫폼 기술의 중요성을 강조하고자 한다. 이러한 M2M과 D2D를 기반으로 하는 융합 서비스의 성공적인 수행은ICT 기반의 개방형 플랫폼의 우선적인 개발이 필요하며, 플랫폼 기반의 디바이스 보급과 네트워크의 구축이 진행되어야 지속 가능한 융합 서비스를 제공할 수 있을 것이다.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1088-1092
• /
• 2018

In this paper, we propose a dual-mode frequency tripler using push-push and stacked FET structures. The proposed circuit can operate either in frequency multiplier mode or in amplifier mode. In the frequency multiplier mode, push-push frequency multiplication is achieved by allowing input signals with particular phase shifts. In the amplifier mode, the device operates as a distributed amplifier to obtain high gain. Also both modes were designed using stacked FET structure. The designed circuit showed frequency tripled output power of 9.7 dBm at 2.4 GHz with the input at 800 MHz. On the other hand, in the amplifier mode, the device showed 8.9 dB of gain to generate 19.5 dBm at 800 MHz.