• 한국재료학회지
• /
• 제28권1호
• /
• pp.18-23
• /
• 2018

To study the impedance characteristics of a fluorescent OLED according to the device structure, we fabricated Device 1 using ITO / NPB / $Alq_3$ / Liq / Al, Device 2 using ITO / 2-TNATA / NPB / $Alq_3$ / Liq / Al, and Device 3 using ITO / 2-TNATA / NPB / SH-1:BD / $Alq_3$ / Liq / Al. The current density and luminance decreased with an increasing number of layers of the organic thin films in the order of Device 1, 2, 3, whereas the current efficiency increased. From the Cole-Cole plot at a driving voltage of 6 V, the maximum impedance values of Devices 1, 2, and 3 were respectively 51, 108, and $160{\Omega}$ just after device fabrication. An increase in the impedance maximum value is a phenomenon caused by the charge mobility and the resistance between interfaces. With the elapse of time after the device fabrication, the shape of the Cole-Cole plot changed to a form similar to 0 or a lower voltage due to the degradation of the device. As a result, we were able to see that an impedance change in an OLED reflects the characteristics of the degradation and the layer.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권9호
• /
• pp.2967-2981
• /
• 2014

Device-to-Device (D2D) communication is a technology component for long-term evolution-advanced (LTE-A). In D2D communication, users in close proximity to each other can communicate directly without going through a base station; such direct communication can improve spectral efficiency. Although D2D communication brings improvement in spectral efficiency, it also causes interference to the cellular network as a result of spectrum sharing. In particularly, D2D communication can generate interference for each D2D pair when the common wireless medium in a co-located limited area is accessed. Even though the interference management for between the D2D pair and cellular networks has been proposed, the interference reducing methods have still not been fully studied for the D2D pairs. In this paper, we investigate the problem of D2D pair coexistence in which interference is considered between D2D pairs. Using a signal to interference model for a target D2D pair, we provide an analysis of the aggregated throughput of a dense D2D network. For a target D2D pair, we assume that the desired signal and interference signals obey multipath fading and shadow fading. Through analysis, we demonstrate the effect of cluster size such as the number of D2D pairs and the size of the considered area on the network performance. The analytical results are compared with computer simulations. Our work can be used for a rough guideline for controlling the system throughput in a dense D2D network environment.

• 대한방사선기술학회지:방사선기술과학
• /
• 제47권3호
• /
• pp.183-195
• /
• 2024

Additional functional upgrades to the large-area compton camera (LACC) measurement device that can provide characteristics evaluation information (nuclear species and radioactivity) and two-dimensional or three-dimensional distribution imaging information of radioactive materials existing in surface or internal of concrete structures are required in terms of work stability and efficiency in order to apply to actual decommissioning sites such as nuclear power plants or medical cyclotron facilities by using this measurement device. To this purpose, the technology that allows radiation workers to intuitively and visually check the distribution of radioactive materials in advance by matching the two-dimensional distribution imaging information of radioactive materials obtained through the LACC measurement device and visual imaging of the measurement zone (10 m × 5 m) was developed. In addition, the separate system that can automatically adjust the position (height) in units of the measurement area size (0.7 m × 0.3 m × 0.8 m) of the LACC measurement device was developed and the integrated management system for characteristics evaluation information and two-dimensional or three-dimensional distribution imaging information obtained per unit of measurement for radioactive materials was developed. These functional upgrades related to LACC measurement device can improve work efficiency and safety when measuring radioactivity of concrete structures and enable the establishment of appropriate decommissioning strategies using radioactivity measurement information for decommissioning nuclear power plants or medical cyclotron facilities.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권6호
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• Bulletin of the Korean Chemical Society
• /
• 제32권5호
• /
• pp.1593-1598
• /
• 2011

Blue fluorescent materials based on 9,9'-diethyl-2-diphenylaminofluorene derivatives were synthesized and characterized. These materials were used as the blue dopant materials for the emitting layer of organic light-emitting diode devices with the following device structure: ITO/DNTPD (40 nm)/NPB (20 nm)/MADN: dopants (2%, 20 nm)/$Alq_3$ (40 nm)/Liq (1.0 nm)/Al. All devices exhibited highly efficient blue emission. One of these devices exhibited a maximum luminance, luminous efficiency, power efficiency and CIE x, y coordinates of 8400 $cd/m^2$, 8.10 cd/A at 20 $mA/cm^2$, 3.36 lm/W at 20 $mA/cm^2$ and (0.151, 0.159), respectively. A deep blue device with CIE coordinates of (0.152, 0.139) showed the maximum luminance, luminous efficiency and power efficiency of 8630 $cd/m^2$, 6.31 cd/A at 20$mA/cm^2$ and 2.62 lm/W at 20 $mA/cm^2$, respectively.

• 한국전기전자재료학회논문지
• /
• 제28권7호
• /
• pp.446-449
• /
• 2015

An improvement of light-extraction efficiency of organic light-emitting diodes was studied by using random-textured films (RTF). Device was made in a structure of RTF/glass/ITO/TPD/$Alq_3$/LiF/Al. RTF mold was made by spreading PDMS solution on a sandpaper. By pressing this mold on the glass substrate pre-coated with ZPU material, the RTF was obtained. From this study, there was an improvement of external quantum efficiency by about 30% in the device with the random-textured film (RTF 40) compared to that of the reference one.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.96-99
• /
• 2000

We fabricated electroluminescent(EL) devices which have a blended single emitting layer containing poly(N-vinylcarbazole)[PVK] and poly(3-dodecylthiophene)[P3DoDT]. The molar ratio between P3DoDT and PVK changed with 1:0, 2:1 and 1:1. To improve the external quantum efficiency of EL devices, we applied insulating layer, LiF layer, between polymer emitting layer and Al electrode. All of the devices emit orange-red light and its can be explained that the energy transfer occurs from PVK to P3DoDT. In the voltage-current and voltage-light power characteristics of devices applied LiF layer, current and light power drastically increased with increasing applied voltage. In the consequence of the result, the external quantum efficiency of the devices that have a molar ratio 1:1 with LiF layer was 35 times larger than that of the device without LiF layer at 6V.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1291-1292
• /
• 2008

ITO is widely used as an anode material in OLED, because of its good transparency, low electrical resistivity, high work function, and efficient hole injection properties. The interface between the electrode and the organic layer in the OLED effects the charge injection process and may influence the electrical and the luminance properties. Surface treatment of ITO, such as an Aquaregia treatment has been shown to enhance the efficiency, and luminance characteristics of the OLED. In this study, we investigated the effect of Aquaregia treatment. The fundamental structures of the OLED were ITO/NPB/$Alq_3$/LiF/Al. The current density-voltage-luminance, efficiency, and lifetime characteristics were measured with untreated and Aquaregia-treated ITO substrates. The Aquaregia treatment was found to enhance the performance of OLED. For the Aquaregia treated device, the maximum luminance and efficiency were increased by about 2 times compared to the untreated device. The mechanism of the Aquaregia treatment is discussed based on AFM analyses.

• 수산해양교육연구
• /
• 제20권3호
• /
• pp.500-507
• /
• 2008

Hot air drying is a method that let moistures evaporate by heat exchange between heating air and dry target. This way is dominating more than about 70% of dryers that the use extent is wide fairly, and is established in domestic than dryer that use conduction or radiation etc. Most of research about drying had been emphasized in size of device through analysis for these dry phenomenon plain, heating topology, and aspect of form and so on by dry target's special quality, and research about device development or waste heat withdrawal technology in energy utilization efficiency side is slight real condition. Therefore, in this study, Investigated numerically about thermal efficiency elevation that is leaned against as that change the temperature of inlet and outlet in heat exchanger of the hot air drying tower.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.176-183
• /
• 2008

Performance of electrostatic diesel PM filtration systems (E-DPS) with different types has been tested using the carbon particles generated by spark discharge in laboratory. Among the five electrostatic precipitators, the multiple wires cylindrical E-DPS with the highest collection efficiency and relatively lower differential pressure at the flow rate of $1\;m^3$/min, as an applicable device to diesel engine as an after treatment system, has been combined with another collection cylinder to improve the collection efficiency of diesel particulate matters generated from diesel engines. The multiple wires cylindrical E-DPS combined with the cylindrical collector showed the collection efficiency of more than 60% at the engine speed of 2,000 rpm with the engine loads of 25 and 50%.