• 한국화재소방학회논문지
• /
• 제30권5호
• /
• pp.82-86
• /
• 2016

건축용 내화강재가 적용된 양단 고정단 보부재의 고온 시 최대 내력과 처짐을 해석적으로 평가하였으며, 이 결과를 일반강재 적용 정정 보부재와의 비교평가를 통하여 안전성을 평가한 결과, 건축용 내화강재 적용 부정정 보부재의 내화성능을 일반 강재 정정 보부재로 평가되는 것은 안전측이었으며, 부재길이가 길어지면 처짐의 증대와 최대 내력의 감소가 유발되는 등 이에 대한 보완책이 요구되는 것으로 나타났다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.194-199
• /
• 2013

Using moving support finite elements, seismic analysis of statically-determinate beams subjected to support motions is performed to show its accuracy and its ease of use. Examples of cantilever and simply-supported beam subjected to support motions are illustrated and the numerical results are compared with the analytical solutions. The examples show the elements facilitate modeling beams with the conventional 2-noded, Hermitian, Euler-Bernoulli beam element. The comparisons of the results with analytical solutions show good agreements with high accuracy.

• 한국해양공학회지
• /
• 제10권4호
• /
• pp.67-74
• /
• 1996

The paper focuse on the effect of a crack subjects to collaspe behabiors of statically indeterminate beams under concentrated load. Through the experiment and calculation, it was revealed that the collaspe load of statically indeterminate beams is much higher than that of statically determinate beams. The cumulative AE event counts of statically determinate beams was less than that of statically indeterminate beams, and the center notch beams sas revealed less than that of the side notch beams.

• 대한기계학회논문집A
• /
• 제37권4호
• /
• pp.555-567
• /
• 2013

지점운동을 받는 베르누이-오일러 보의 동적 유한요소해석을 위하여, 준정적 분해법을 사용하여 유한요소 정식화 및 지점운동 묘사를 위한 보요소를 개발하였다. 이 보요소들은 전통적인 2 절점 Hermitian 보 요소로서 기존의 모델링 방법을 그대로 따르면서 한 쪽 절점이 운동하는 지점과 일치하는 경우 해당 요소만을 본 연구에서 제안하는 요소로 대체하여 사용할 수 있도록 수식화하였다. 이 요소의 유용성과 정확성을 보이기 위해 지점운동을 받는 정정보들에 대해 수치실험을 실시하고 그 결과들을 이론해와 비교함으로써 사용이 간편함과 동시에 정확도가 매우 높다는 사실을 보였다.

• Tribology and Lubricants
• /
• 제8권2호
• /
• pp.50-63
• /
• 1992

The minimum oil film thicknesses (MOFT) in the crankshaft main bearings of a 1.5 liter, L-4, gasoline engine are measured and calculated to study the dynamically loaded engine bearing. The MOFT are measured simultaneously at each of the five main bearings using the total capacitance method(TCM). To improve the reliability of the TCM, a reasonable determination method of bearing clearance is introduced and the effects of bearipg cavitation and aeration on the test results are analyzed. Also the crankshaft is grounded by means of a slip ring instead of the friction contact method to improve the test precision. The calculation is based on the model of statically determinate beam, short bearing approximation and Mobility method. From the comparison between the measured and calculated MOFT curves, it is found that a qualitative similarity exists between them, but in all cases, measured MOFT are smaller than that of calculated. The crankshaft vibration and the imbalance of the load distribution between the engine bearings have important influence upon the MOFT curve. So it is found that the calculation result from the model of the statically determinate beam has a limitation in predicting bearing performance.

• 한국정밀공학회지
• /
• 제19권1호
• /
• pp.93-98
• /
• 2002

It is important to determinate the shear center of beam having arbitrary cross-section in structures. In this study, we have introduced the determination of shear center that gets the equivalent stiffness matrix representing arbitrary cross section of beam and applies energy equivalence theory. This method shows the results of applying on examples that we know the exact and approximate solution of open and cross section of beam. This study also compares with the shear center of composite rotor blade got by the experiment and by the suggested method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.188-193
• /
• 2013

The large mass method for dynamic analysis of statically determinate beams subjected to in-phase support motions is justified by showing that the equation of motion of the beams under consideration is equivalent to that of large mass model of the beam when an appropriate large mass ratio is employed. The accuracy of the stress responses based on the beam large mass method is investigated through careful numerical tests. The numerical results are compared to analytic solutions and the comparison shows that the large mass method yields not only the time history of motion but also the distributions of bending moment and shear force accurately.

• 한국화재소방학회논문지
• /
• 제29권5호
• /
• pp.23-28
• /
• 2015

건축물의 공간 효율성 증대를 주 목적으로 고강재 강재(SM 520)의 사용이 활성화되고 있으나, 화재와 같은 고온조건에서의 보부재에 대한 내화성능은 검증되지 못하고 있는 실정이다. 따라서 본 연구에서는 SM 520강재가 적용된 양단 고정단 경계조건인 부정정 보부재를 대상으로 표준화재온도곡선과 고온에서의 항복강도, 탄성계수 그리고 비열, 선팽창계수를 적용하는 해석적 방법을 통하여 내화성능을 평가하고, 이를 바탕으로 일반 구조용 강재에 의한 보부재의 내화성능 평가의 안전성을 확인하였다.

• Steel and Composite Structures
• /
• 제15권1호
• /
• pp.81-101
• /
• 2013

In this paper a robust 2-noded connection element has been developed for modelling the bolted end-plate connection between steel beam and column at elevated temperatures. The numerical procedure described is based on the model proposed by Huang (2011), incorporating additional developments to more precisely determinate the tension, compression and bending moment capacities of end-plate connection in fire. The proper failure criteria are proposed to calculate the tension capacity for each individual bolt row. In this new model the connection failure due to bending, axial tension, compression and shear are considered. The influence of the axial force of the connected beam on the connection is also taken into account. This new model has the advantages of both the simple and component-based models. In order to validate the model a total of 22 tests are used. It is evident that this new connection model has ability to accurately predict the behaviour of the end-plate connection at elevated temperatures, and can be used to represent the end-plate connections in supporting performance-based fire resistance design of steel-framed composite buildings.

• 대한조선학회논문집
• /
• 제53권3호
• /
• pp.188-194
• /
• 2016

Accurate estimation of shear flows in thin-walled beam section is the key issue to evaluate shear stress distribution of ship hull transverse section under the shear forces acting on hull girder. It is regarded that the method using the warping functions obtained by finite element formulation is the state of the art of this field. Recently, however, IACS took effect the new version of CSR in which direct calculation process of shear flow was suggested. In the direct calculation process, shear flow of ship hull section can be obtained by the addition of determinate and indeterminate shear flows calculated respectively. So, in this paper, the shear flow evaluation codes based on the process proposed by IACS CSR and warping function based method were developed respectively. The calculated results of shear flows for the several examples of ship sections were compared with each other and considered in detail.