• Composites Research
• /
• v.13 no.6
• /
• pp.47-54
• /
• 2000

One promising method for impact detection of composite structures is based on the use of piezopolymer thin fim (PVDf) sensor. In this paper, the relationship between the contact force and the signals of the attached strain gage and PVDF sensor to the composite plate subjected to low-velocity impact were derived. The relation for the open circuit and short circuit voltage of PVDF sensor was derived based on the equivalent circuit model of the piezoelectric sensor. The work was then extended to include experimental investigation into the use of short circuit voltage of PVDF sensor without using charge amplifier to detect low-velocity impact. The natural frequencies and damping ratio of the composite plate obtained from the vibration test were used to modify the analytical model and therefore the differences between measured and simulated signal of the modified analytical model in both forward and backward problem were considerably reduced. The reconstructed contact force and simulated sensor signals agreed well with the measured contact force, strain gage signal, and PVDF sensor singanl.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.5
• /
• pp.1110-1116
• /
• 2017

Depending on the operating characteristics, track circuit is installed for the purpose of direct or indirect control of the signal device, point switch machine and other security device. These are mainly used for train detection, transmission of information, broken rail detection and transmission of return current. Especially, the return current is related to signal system, power system and catenary line, and track circuit systems. It is one of the most important component shall be dealt for the safety of track side staff and for the protection of railway-related electrical system according to electrification. Therefore, an accurate analysis of the return current is needed to prevent the return current unbalance and the system induced disorder and failure due to an over current condition. Also, if the malfunction occurred by the return current harmonics, it can cause problems including train operation interruption. In this paper, we presented measurement and analysis method at return current and it's harmonics by high speed train operation on the honam high speed line.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.143-148
• /
• 2020

In the case of a system that detects and controls the phase of an alternating voltage, the analog control method compensates the phase offset part by filtering for the detected phase and applies it to the control. However, in the digital control method, precise control cannot be achieved due to an error between the operating frequency of the microprocessor or the microcontroller and the input phase time when controlled using such phase detection. In general, when the method used is a certain time, the accumulated error is compensated and adjusted at random. To solve this problem, a method of detecting a zero point in real time and compensating for the operating frequency of the microprocessor is needed. Therefore, the research to be performed in this paper to reduce these errors and apply them to precise digital control is as follows. 1) Research on how to implement Zero Crossing Detection algorithm through simulation modeling to compensate the zero point to match the operating frequency through detection. 2) A study on the method of detecting zero points in real time through the Zero Crossing Detection design using a microcontroller and compensating for the operating frequency of the microprocessor. 3) A study on the estimation of the rotor position of BLDC motors using the Zero Crossing Detection circuit.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.2
• /
• pp.39-45
• /
• 2004

This paper describes the design and implementation of Serial ATA physical layer and performance measurement. It is composed of tranceiver circuit that has the NRZ data stream with +/-250㎷ voltage level and 1.5Gbps data rate, transmission PLL circuit, clock ＆ data recovery circuit, serializer/deserializer circuit and OOB(Out Of Band) generation/detection circuit. We implement the verification of the silicon chip with 0.18${\mu}{\textrm}{m}$ Standard CMOS process. It can be seen that all of the blocks operate with no errors but the data transfer rate is limited to the 1.28Gbps even this should support 1.5Gbps data transfer rate.

• Journal of the Korea Convergence Society
• /
• v.11 no.10
• /
• pp.63-69
• /
• 2020

In this paper, a small microwave sensor that can be applied to a wearable device is proposed because it can detect the heartbeat signal of a human body moving irregularly at low speed. It consist of balanced microstrip radiation patches in the 2.4 GHz ISM band, self-oscillation detection circuit, and feedback circuit. Based on the theoretical development and simulation, the validity of the proposed structure was confirmed and the manufactured prototype was tested. The board size of the circuit is as small as 65mm × 85㎟, and has a low power consumption of 60mW thanks to the simple RF circuit structure. Finally heartbeat signal has been obtained from a human body moving at low speed (0.5Hz) within a linear distance of 2 to 30mm close to the sensor and a lateral distance of ±20mm.

• Journal of IKEEE
• /
• v.13 no.3
• /
• pp.1-6
• /
• 2009

In this paper, the external matching circuits were designed in order to compensate the efficiency which decreases by human body effect in the internal antenna phone. Comparing the two types of matching circuit, we selected the structure to minimize the switch stress. RF MEMS switch using low voltage was compared with FET switch and measured the performance in the handset. Here, the detection circuit which can couple th reflection power from antenna was added in the handset and we set up the demonstration system that can compensate the loss of hand effect automatically. In this system, when hand effect occurred, the radiation power increased 2.5dB by operation the matching circuit.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.2
• /
• pp.25-28
• /
• 2004

Three-phase inductive superconducting fault current limiter (SFCL) with DC reactor rated on 6.6 $KV_{rms}/200 A_{rms}$ has been developed in Korea. This system consists of one DC reactor, AC/DC power converter, and a three-phase transformer, which is called magnetic core reactor (MCR). This paper deals with the short-circuit analysis of the SFCL. The DC reactor was the HTS solenoid coil whose inductance was 84mH. The power converter was performed as the dual-mode operation for dividing voltage between the rectifying devices. The short-term normal operation (1 see) and short-circuit tests (2∼3 cycles) of this SFCL were performed successfully. In regular short-circuit test, the fault current was limited as 30% of rated short-circuit current at 2 cycles after the fault. The experimental results have a very similar tendency to the simulation results. Using the technique for the fault detection and SCR firing control, the fault current limiting rate of the SFCL was improved. From this research, the parameters for design and manufacture of large-scale SFCL were obtained.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.955-957
• /
• 1998

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia, and high poer rate per unit volume. However, position sensor isessential in SRM in order to synchronize the phase excitation to the rotor position. The position sensors increase the cost of drive system, and tend to reduce system reliability. This paper investigtes the speed control of sensorless SRM. The proposed system consists of position detection circuit, dwell angle controller, digital logic commutator, PI speed controller and 4-phase inverter. The performances in the proposed system are verified through the experiment.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.112-115
• /
• 2000

This paper describes the algorithm, architecture and design of the circuit implementing motion tracing features based on the edge detection. The Sobel operation was used to compute the edges of moving objects. Motion tracing is performed by searching for the center of the edges for each frame and adding those centers. The edger and the centers of the moving object from camera were displayed in the monitor and verified using Xillinx FPGA.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.149-152
• /
• 2001

In this paper, a 1.5V 2㎓ low-power peak detector is presented. Analyzing the designed peak detector circuit which is composed with two NMOSs, two diodes, and two capacitors, the detection characteristic relationships are derived. The simulation results with SPICE for 2㎓ pulse signals and sinusoidal signals on the 1.5V supply voltages show the good detection characteristics for input signal levels of 50㎷~500㎷, and show very small power dissipation of 0.332㎽.