• 사물인터넷융복합논문지
• /
• 제10권2호
• /
• pp.103-108
• /
• 2024

본 논문에서는 YOLO(You only look once)v5를 기반으로 한 실시간 객체 검출 기술을 활용하여 스마트 엘리베이터 시스템을 연구하였다. 외부 엘리베이터 버튼이 눌러지면 YOLOv5 모델이 카메라 영상을 분석하여 대기자의 유무를 판별하고, 대기자가 없다고 판별되면 해당 버튼을 자동으로 취소시킨다. 연구에서는 YOLOv5와 사물인터넷에서 활용되는 MQTT(Message Queuing Telemetry Transport)를 통한 객체 탐지 및 통신 기술의 효과적인 구현 방법을 소개한다. 그리고 이를 활용하여 대기자 유무를 실시간으로 판별하는 스마트 엘리베이터 시스템을 구현하였다. 제안한 시스템은 불필요한 소비 전력을 절감하면서 CCTV(closed-circuit television)의 역할을 할 수 있다. 따라서 제안한 스마트 엘리베이터 시스템은 안전 및 치안 문제에도 기여할 수 있을 것으로 기대한다.

• 한국지반환경공학회 논문집
• /
• 제24권12호
• /
• pp.61-67
• /
• 2023

도심지 지하에 위치하며 고온, 고압조건에서 운영되는 열수송관은 파손 시 인적, 경제적으로 대규모 피해가 발생할 수 있다. 파손을 사전에 예측하기 위해 기존 파손이력과 설비이력을 분석하여 파손빈도와 상관관계를 가지는 독립변수를 도출하고, 각 변수를 활용한 단순회귀분석 변형모델이 현장에 적용되고 있다. 다만, 모델에 적용되는 독립변수간 상관관계가 클수록 변수간 독립성이 훼손되어 모델의 신뢰성이 낮아진다. 본 연구에서는 상호 연관성을 가지는 것으로 판단되는 관경, 매설깊이, 감시시스템 절연레벨, 감지선의 단선 또는 단락의 독립성을 검정하여 파손빈도 추정모델에 적용하기 위해 필요한 변수간 결합 및 범주 설정 방안을 도출하였다. 독립성 검정을 위해 연속형 변수인 관경과 매설깊이는 각각 3개의 범주, 감시시스템 절연레벨은 2개의 범주로 변환하였으며, 범주형 변수인 감시시스템 감지선 상태는 범주를 그대로 2개로 유지하였다. 독립성 검정 결과, 관경과 매설깊이간, 감시시스템 절연레벨과 감지선의 단선 또는 단락간 유의확률이 유의수준(α = 0.05)보다 작아 상호간 상관관계가 큰 것으로 나타났다. 따라서 관경과 매설깊이를 하나의 변수로 결합하고 사전에 설정한 범주를 고려하여 결합 변수의 범주는 9개로 설정하였다. 감시시스템 절연레벨과 감지선의 단선 또는 단락 역시 하나의 변수로 결합하였으며, 감지선 상태가 단선 또는 단락인 경우 절연레벨값을 신뢰할 수 없으므로 결합 변수의 범주는 3개로 설정하였다.

• 전기학회논문지
• /
• 제64권9호
• /
• pp.1315-1322
• /
• 2015

This paper proposes an active islanding detection method for the BESS (Battery Energy Storage System) with 3-phase inverter which is connected to the AC grid. The proposed method adopts the DDSRF (Decoupled Double Synchronous Reference Frame) PLL (Phase Locked-Loop) so that the independent control of positive-sequence and negative-sequence current is successfully carried out using the detected phase angle information. The islanding state can be detected by sensing the variation of negative-sequence voltage at the PCC (Point of Common Connection) due to the injection of 2-3% negative-sequence current from the BESS. The proposed method provides a secure and rapid detection under the variation of negative-sequence voltage due to the sag and swell. The feasibility of proposed method was verified by computer simulations with PSCAD/EMTDC and experimental analyses with 5kW hardware prototype for the benchmark circuit of islanding detection suggested by IEEE 1547 and UL1741. The proposed method would be applicable for the secure detection of islanding state in the grid-tied Microgrid.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2005년도 종합학술발표회 논문집 Vol.15 No.1
• /
• pp.191-196
• /
• 2005

A low-cost, high-performance 40 Gb/s clock recovery module using a phase-locked loop(PLL) for a 40 Gb/s optical receiver has been designed and implemented. It consists of a clock recovery circuit, a RF mixer and frequency discriminator for phase/frequency detection, a DR-VCO, a phase shifter, and a hold circuit. The recovered 40 GHz clock is synchronized with a stable 10 GHz DR-VCO. The clock stability and jitter characteristics of the implemented PLL-based clock recovery module has shown to significantly improve the performance of the conventional open-loop type clock recovery module with DR filter. The measured peak-to-peak RMS jitter is about 230 fs. When input signal is dropped, the 40 GHz clock is generated continuously by hold circuit. The implemented clock recovery module can be used as a low-cost and high-performance receiver module for 40 Gb/s commercial optical network.

• 조명전기설비학회논문지
• /
• 제28권2호
• /
• pp.70-75
• /
• 2014

A track circuit is a critical piece of equipment that allows the existence of the trains on the track to be detected. Train detection is very important for the signal safety equipment. It allows for the confirmation of a train's location, the locking of switch points, the coordination of safe distance between trains, and the advance notice of a train's arrival. Track circuits can be powered by AC or DC. The DC track circuits are usually used on non-electrified tracks. On these tracks, many signal errors can be caused by lightning or problems with the power source. These problems can also cause damages to the rectifiers which must be repaired or replaced, promptly. This issue is especially problematic in the summer because of the higher frequency of thunderstorms. Issues with track circuits also cause problems for other equipment, such as railroad crossings and switch points. This further disrupts the safe operation of trains. This study aims to enhance maintenance efficiency and improve safety by utilizing parallel operation and multiplexing of a DC track circuit as well as installing an external surge protector. The experimental results on the operation of the proposed method is also presented.

• 한국안전학회지
• /
• 제29권5호
• /
• pp.54-59
• /
• 2014

The record type receivers that are operated in large industrial sites have strength in preventing fire. However, because of its long circuit lines and multiple detectors, the receivers are vulnerable to lightning, noise, and breakdown of equipments, resulting in malfunction. In case of malfunctioning of detection circuits of main protection areas, such as electrical room and server room, potential release of gaseous extinguisher agents may lead to property and life damage. In this paper, we present the results on the characteristics of the transponder that initiates the solenoid valves, with respect to various electromagnetic and lightning inflow conditions. Based on the measured data, we analyzed the systematic problems of the transponder. In order to prevent receiver malfunctions, a sequential circuit was configured with two additional transponders and a timer. The circuit was tested with a simulator with preference and delay circuit algorithms.

• 전기학회논문지
• /
• 제64권1호
• /
• pp.182-187
• /
• 2015

In the three-phase power system, when any one-phase or two-phases is open-phase, the unbalanced current flows and the single-phase power supplies to three-phase loads. Specially, motor coil and transformer coil receive over-current. As a result, great damage as well as electrical fire can occur to the power system. In order to improve these problems, this paper proposes that an open-phase detection device is designed by a new algorithm using electric potential difference between the resultant voltage of neutral point and ground, and a control circuit topology of open-phase protector is composed of highly efficient semiconductor devices. It improves response speed and reliability. The control algorithm circuit also operates the cut-off of a conventional residual current protective device (RCD) which flows an enforced leakage current to ground wire at open-phase accident. Furthermore, time delay circuit is added to prevent the incapable operation of open-phase protector about instantaneous open-phase not open-phase fault. The time delay circuit improves more reliability.

• 센서학회지
• /
• 제20권6호
• /
• pp.375-381
• /
• 2011

Ionic polymer-metal composite(IPMC) consists of an ion conductive membrane plated by metallic electrodes on both surfaces. When it bends, a voltage is generated between two electrodes. Since IPMC is flexible and thin, it can be easily mounted on the various surfaces of a body. The present study investigates a sensor system using IPMC to effectively detect the bending angles applied on IPMC sensor. The paper evaluates several R and C circuit models that describe the physical composition of IPMC and selects the best model for the detection of angles. The circuit models implemented with a charge model describe the relationship between input bending angles and output voltages. The identification of R and C values was performed by minimizing the error between the real output voltages and the simulated output voltages from the circuit models of IPMC sensor. Then the output signal of a sensor was fed into the inverse model of the identified model to reproduce the bending angles. In order to support the validation of the model, the output voltages from an arbitrary bending motion were also applied to the selected inverse model, which successfully reproduced the arbitrary bending motion.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.707-710
• /
• 2002

A 120kV/70A high voltage switch has been installed at Korea Atomic Energy Research Institute in Taejon to supply power with Korea Superconducting Tokamak Advanced Research (KSTAR) Neutral Beam Injection (NBI) system. NBI system requires fast cutoff of the power supply voltage for protection of the grid when arc detected and fast turn-on the voltage for sustaining the beam current. Therefore the high voltage switch and arc current detection circuit are important part of the NBI power supply and there are much need for high voltage solid state switches in NBI system and a broad area of applications. This switch consisted of 100 series connected MOSFETs and adopted the proposed simple and reliable gate drive circuit without bias supply, Various results taken during the commissioning phase with a 100kW resistive load and NBI source are shown. This paper presents the detailed design of 120kV/70A high voltage MOSFETs switch and simple gate drive circuit. Problems with the high voltage switch and gate driver and solutions are also presented.

• The Journal of the Acoustical Society of Korea
• /
• 제14권2E호
• /
• pp.43-49
• /
• 1995

인공지능(AI)의 한기법인 Space Search 기법을 이용하여 회로의 단선 결함의 유무 및 결함위치를 찾아내는 방법을 제시하였다. 보통 회로의 결함은 단선 및 단락의 구조적 결함으로 나뉘어진다. 두가지 결함 모두 회로의 기능에 중대한 이상을 초래한다. 그중 단선에 의한 회로의 결함에 대하여 다루었다. 우선 회로를 net와 net의 연결 path에 따라 tree 구조로 변환하였다. 서로 독립된 net들은 서로 다른 tree의 node를 이루며 각각의 tree는 적기적으로 연결됨이 없다. 각 tree의 최상단부의 root node에 test vector를 입력하고 최하단부의 leaf node에서 vector를 관찰하여 입력된 test vector와 비교한다. 그 비교 결과 동일 유무에 따라 결함의 유무를 판정한다. 결함이 있다고 판정된 leaf node는 depth search 방법에 의하여 root node쪽으로 test vector를 관찰하여, 전기적 신호에 의하여 회로의 서놔 단선된 위치를 찾아내도록 하는 방법을 제시하였다.