• Structural Engineering and Mechanics
• /
• v.41 no.1
• /
• pp.1-24
• /
• 2012

A reinforced concrete (RC) framed structure detailed according to non-seismic detailing provisions as per Indian Standard was tested on shake table under dynamic loads. The structure had 3 main storeys and an additional storey to simulate the footing to plinth level. In plan the structure was symmetric with 2 bays in each direction. In order to optimize the information obtained from the tests, tests were planned in three different stages. In the first stage, tests were done with masonry infill panels in one direction to obtain information on the stiffness increase due to addition of infill panels. In second stage, the infills were removed and tests were conducted on the structure without and with tuned liquid dampers (TLD) on the roof of the structure to investigate the effect of TLD on seismic response of the structure. In the third stage, tests were conducted on bare frame structure under biaxial time histories with gradually increasing peak ground acceleration (PGA) till failure. The simulated earthquakes represented low, moderate and severe seismic ground motions. The effects of masonry infill panels on dynamic characteristics of the structure, effectiveness of TLD in reducing the seismic response of structure and the failure patterns of non-seismically detailed structures, are clearly brought out. Details of design and similitude are also discussed.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.350-359
• /
• 2011

This paper describes the operational analysis results of a DC micro-grid using a detailed model of distributed generation. A detailed model of wind power generation, photo-voltaic generation and fuel cell generation was implemented with an userdefined model created with PSCAD/EMTDC software and coded in C-language. The operational analysis was carried out using PSCAD/EMTDC software, in which the power circuit is implemented by a built-in model and the controller is modeled by an user-defined model that is also coded in C-language. Various simulation results confirm that a DC micro-grid can operate without any problems in both the grid-tied mode and in the islanded mode. The operational analysis results confirm that the DC micro-grid makes it feasible to provide power to the load stably. It can also be utilized to develop an actual system design.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1183-1188
• /
• 2009

Estimating project costs during the early stage of conceptual planning is very important when deciding whether to approve the project and allocate an appropriate budget. However, due to greater uncertainties involved in a project, it is challenging to estimate costs during this initial stage within a reasonable tolerance. This paper attempts to develop a cost-estimate model for public road projects under these circumstances and limitations. In the conceptual planning stage of a road project, there is only limited information for cost estimation, for example, such input data as total length of the route, origin and destination, number of lanes, general geographic characteristics of the route, and other basic attributes. This implies that the model should individuate suitable but restricted information without considering detailed features such as quantity of earthwork and a detailed route of a given condition. With these limited facts, this paper applies a case-based reasoning (CBR) method to solve a new problem by deriving similar past problems, which in turn is used to estimate the cost of a given project based on best-fitted previous cases. To develop a CBR cost-estimate model, the authors classified 8 representative variables, including project type, the number of lanes, total length, road design grades, etc. Then, we developed the CBR model, primarily by using 180 actual cases of public road projects, procured over the last decade. With the CBR model, it was found that the degree of error in estimation can be reasonably reduced, to below approximately 30% compared to the final costs estimated upon the completion of detailed design.

• Korean Journal of Construction Engineering and Management
• /
• v.23 no.5
• /
• pp.87-97
• /
• 2022

Although the use of BIM in architectural projects has increased, repetitive modeling tasks and frequent design errors remain as obstacles to the practical application of BIM. In particular, interior finishing elements include the most varied and detailed requirements, and thus requires improving its modelling efficiency and resolving potential design errors. Recently, visual programming-based modules has gained traction as a way to automate a series of repetitive modeling tasks. However, existing approaches do not adequately reflect the practical modeling needs and focus only on replacing siimple, repetitive tasks. This study developed and evaluated the performance of three modules for automatic detailing of walls, floors and ceilings. The three elements were selected by analyzing the man-hours and the number of errors that typically occur when detailing BIM models. The modules were then applied to automatically detail a sample commercial facility BIM model. Results showed that the implementations met the practical modeling requirements identified by actual modelers of an construction management firm.

• Journal of Practical Engineering Education
• /
• v.14 no.2
• /
• pp.235-244
• /
• 2022

In this study, a class operation case of an engineering design project targeting a golf ball dispenser, a commercial product, was presented. The project was carried out according to the systematic engineering design approach suggested by Kim Jong-won and W. Beitz. This method broadly divides engineering design into four stages: 'product planning → conceptual design → basic design → detailed design'. In particular, the conceptual design stage is divided into 'functional structure diagram → detailed working principle exploration → various design alternatives creation → optimal design selection'. In the conceptual design, the input/output of the golf ball dispenser was defined and a functional structure diagram was prepared for it. Through this process, it was possible to subdivide the functions of the product and to easily explore the working principle for each. The searched working principles are devised as various design alternatives by various combinations, and for each proposal, the advantages and disadvantages were compared with each other to derive the optimal design alternative. In the basic design, the prototype layout was completed through failure mode analysis and the actual prototype was manufactured using it. Through the entire process, students participating in the class will be able to design commercial products in a systematic way and experience manufacturing prototypes within the department of mechanical engineering curriculum.

• Korean Journal of Computational Design and Engineering
• /
• v.11 no.2
• /
• pp.77-87
• /
• 2006

It is necessary to change the existing design process to cope with a short life-cycle product and various customer's demands. Also a frequent design change may delay the whole design process and it will increase the unit cost of the production. New alternatives or techniques have emerged to solve the existing design problems, such as a knowledge based engineering, an intelligent CAD, a function based design, and so on. In this paper, we propose a hybrid design system with a knowledge based design methodology and a function based design technique. The knowledge based design is good at a frequent design change and the function based design is effective to extract a core design behavior. In an early design process, the system utilizes a core design behavior through the function based design process. On the other hand, the system manages complicated design issues with the knowledge based design technique in the detailed design process. We conclude that the hybrid design system can bring fair effects on implementing an efficient design environment in aspect of time and expense.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2130-2137
• /
• 2020

The standard method for calculating anti-neutrino emissions from a reactor involves knowing the fractional fission rates for the most important fissioning nuclides in the reactor. To calculate these rates requires detailed reactor physics calculations based upon the reactor design, fuel design, burnup dependent fuel composition, location of specific fuel assemblies in the core and detailed operational data from the reactor. This has only been published for a few reactors during specific time periods, whereas to be of practical use for anti-neutrino reactor monitoring it is necessary to be able to predict these on the publicly available information from any reactor, especially if using these data to subtract the anti-neutrino signal from other reactors to identify an undeclared reactor and monitor its operation. This paper proposes a method to estimate the fission fractions for a specific reactor based upon publicly available information and provides a database based upon a series of spent fuel inventory calculations using the FISPIN10 code and its associated data libraries.

• Radiation Oncology Journal
• /
• v.10 no.1
• /
• pp.95-100
• /
• 1992

Since LINAC-based stereotactic radiosurgery uses multiple noncoplanar arcs, three-dimensional dose evaluation and many beam parameters, a lengthy computation time is required to optimize even the simplest case by a trial and error. The basic approach presented in this paper is to show promising methods using an experimental optimization and an analytic optimization The purpose of this paper is not to describe the detailed methods, but introduce briefly, proceeding research done currently or in near future. A more detailed description will be shown in ongoing published papers. Experimental optimization is based on two approaches. One is shaping the target volumes through the use of multiple isocenters determined from dose experience and testing. The other method is conformal therapy using a beam's eye view technique and field shaping. The analytic approach is to adapt computer-aided design optimization in finding optimum irradiation parameters automatically.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.14 no.3
• /
• pp.177-193
• /
• 2012

The purpose of this study is making a contribution to expand course of employment precluding students from fear and perception of danger related to establishing fashion business and improving self-confidence with practical businesses through an education experiencing in establishing fashion business with united both theory and practice. In this study, A Merchandise-Process consisting of researching, merchandising, marketing, selling has been applied after selection of fashion items by 4 groups of applicants. As a result, the result of these applicants's reaction has shown that most of them has improved self-confidence and felt a sense of accomplishment about practical businesses. The Applicant has experienced the market situation, realized reality of the business and formed human relationships with many people through the marketing. In conclusion, experience of applicants has shown that practical education is important because it was providing applicants with self-confidence of establishing fashion business, importance of teamwork and a sense of accomplishment about making a profit. Therefore, converting theoretical education to practical education is needed. A limitation of this study is that the detailed part of merchandising was omitted because the whole course of merchandising should be accomplished within a semester. To develop this study, detailed proceeding methods divided by one process is required.

• Journal of the Korean Society of Costume
• /
• v.56 no.7 s.107
• /
• pp.68-84
• /
• 2006

The aim of this study is to examine a structure of trousers worn by males in the western world during the 17th and 18th centuries in order to understand the characteristics of evolution in construction. it mainly examined engravings from these era because they provided me fine and detailed portrayals of what it needed to observe. Then, it classified them into models according to each era. it supplemented a flaw of depending on single type of studying material by examining other types of historical materials such as historical paintings and documents for comparative analysis of materials and decorations and previous studies on preserved historical documents to observe the examples of structures of trousers. Secondly, it studied both historical documents and previous studies on the trousers patterns used back in those days, analyzed the characteristics of each designing method by actually draping these patterns, and observed the differences in these completed patterns to understand the characteristics of changes in fashion design skill. As for the changes in length, these patterns show only a slight difference around above and below the knee line. However, the widths of waist, hip, girth and hem were significantly altered over the years to reduce wrinkles and the cutting lines became more refined to make the clothes fit to the body. As a result, a simple but fine patterning technique was born. In particular, new methods in cutting and sewing were invented for detailed parts such as waist, pocket, front and slit.