• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.9 s.339
• /
• pp.29-34
• /
• 2005

This paper describes a novel internal clock generator, called duty cycle-corrected analog synchronous mirror delay (DCC-ASMD). The proposed circuit is well suited for dual edge-triggered systems such as double data-rate synchronous DRAM since it can achieve clock synchronization within two clock cycles with accurate duty cycle correction. To evaluate the performance of the proposed circuit, DCC-ASMD was designed using a $0.35\mu$m CMOS process technology. Simulation results show that the proposed circuit generates an internal clock having $50\%$ duty ratio within two clock cycles from the external clock having duty ratio range of $40\;\~\;60$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.3-9
• /
• 2015

In this paper, we propose the operation procedures of the 1-channel monopulse receiver which achieves the new configuration. Also, we analyzed the monopulse ratio and the target angle accuracy of the fabricated receiver by using the monopulse signal generator developed for verifying the proposal equipment. As a result, it is apparent that the monopulse ratio of the proposal receiver is equal to that of the 3-channel monopulse receiver. Also, the fabricated receiver exhibits the target angle accuracy with fewer than 0.1 RMS. The proposal receiver achieves the simple receiver configuration and the simple tracking procedures, as contrasted with the 3-channel monopulse receiver. Also, the proposal receiver has advantages in terms of size, weight, cost and power. Because the proposal monopulse receiver requires 1-channel receiver and needs not the signal processor in comparison with 3-channel monopulse receiver which requires 3-channel receiver and need the signal processor.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.12
• /
• pp.1579-1584
• /
• 2011

This paper discusses an energy system that can convert wave energy into electrical energy. This wave energy generation system is movable and has 12 arms and one generator. A multibody dynamic model for this system is established by using kinematic constraints. A gear mechanism, several kinematic constraints, and force elements are included in the model. Wave forces are obtained numerically from the time domain formulation based on the Morison equation. The MSC/ADAMS program is employed to carry out dynamic analysis of the wave energy generation system. The dynamic behavior responses of this system are analyzed for design verification. According to the results of the dynamic analysis, the yaw motion is relatively stable and kinetic energy sufficient to generate electrical energy is obtained when the wave height exceeds 1m.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10A
• /
• pp.796-806
• /
• 2009

This paper presents the method of emergency warning system operation based on T-DMB and the design of T-DMB AEAS receiver model. The proposed receiver model compares the geographical location of emergency with the location of DMB transmitting station from T-DMB broadcasting signal and classifies the receiver location into alert region, neighboring region and non-alert region and transmits the emergency alert message according to each region. The geographical location of emergency can be obtained from FIG 5/2 EWS data field for AEAS message and the location of DMB transmitting station can be estimated from either the latitude and the longitude in main identifier and sub identifier in FIG 0/22 data filed for TII(Transmitter Identification Information) or TII distribution database. In our experiment, we implemented the proposed receiver model with display section, storage section, DMB module for receiving broadcasting signal and control section and performed test emergency alert broadcasting using T-DMB signal generator.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.1
• /
• pp.545-550
• /
• 2023

A pretensioner is a safety device that protects occupants by pulling the seat belt in the event of a vehicle collision. However, since the pretensioner is driven by a explosive method, it is necessary to replace not only the gas generator but also all connecting parts including the manifold after an accident. Therefore, in this paper, we propose an elastic force-based pretensioner that can be used safely and semi-permanently. After analyzing the operating mechanism of the existing pretensioner from a thermodynamic/dynamic point of view, the spring stiffness that can be deployed within an appropriate operating time was determined by converting the gas explosion energy into elastic energy. In addition, the coil spring shape that satisfies the elastic stiffness was designed in consideration of the vehicle interior installation standard. Finally, the operating performance of the pretensioner driven by elastic force was verified through fabrication.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.258-265
• /
• 2006

In this paper, an active clamping sepic-flyback converter has been proposed, which is suitable for a fuel cell based power generation system. The proposed converter is superposition of sepic converter mode and flyback mode. It has outstanding high boosting output voltage, component utilization and high efficiency characteristics under the inherently severe low output voltage of the fuel cell generator. In this paper, the validity of the proposed converter has been verified by the informative simulation and experimental results that make used of the PEMFC.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.668-672
• /
• 2001

The utility interactive sinewave modulated inverter for the solar photovoltaic (PV) power conversion and conditioning with a new high frequency pulse modulated link is presented for domestic residential applications. As compared with the conventional full-bridge hard switching PWM inverter with a high frequency AC link, the simplest single-ended quasi-resonant soft switching sinewave modulated inverter with a duty cycle pulse control is implemented, resulting in size and weight reduction and low-cost. This paper presents a prototype circuit of the single-ended zero voltage soft switching sinewave inverter for solar power conditioner and its operating principle. In addition, this paper proposes a control system to deliver high quality output current. Major design of each component and the power loss analysis under actual power processing is also discussed from an experimental point of view. A newly developed interactive sinewave power processor which has $92.5\%$ efficiencty at 4kW output is demonstrated. It is designed 540mm-300mm-125mm in size, and 20kg in weight.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.9C
• /
• pp.652-660
• /
• 2008

Applications running under embedded systems require various device drivers designed for different types and versions of the OS to manage resources effectively. In this paper, an automated device driver generator system which can generate the device drivers to be used in newer versions the target OS is proposed. In the proposed system, the structures of device drivers of specific OS are designed in the templates and stored in a library, and the target device drivers are generated by adding codes to the stored templates. Once device drivers are generated, they are registered into the kernel. The experimental results show that data transfer time has been slightly increased when compared against manually created drivers for TFT-LCD driver, USB interface keyboard/mouse driver, and AC'97 controller drivers. The code size for the generated drivers after compilation has also been increased slightly when compared with manually designed device drivers.

• Journal of the Institute of Convergence Signal Processing
• /
• v.14 no.3
• /
• pp.181-190
• /
• 2013

In this paper, we designed file system in order to utilize data analysis by using correlation result from Daejeon correlator including related software development. Correlation results are consisted of visibility component (amplitude and phase) of radio source, but for data analysis of correlation result, various information such as weather, radio telescope position, observation time, radio source position, source type, and receiver noise temperature are needed. In this paper, we designed file system as a directory-structure for making use of these informations at Linux system for analyzing data and developed software to make file system. To verify the effectiveness of designed file system and developed software, file system generation experiment is conducted, and then astronomers accepted that there is no severe problem for scientific analysis using designed file system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.223-229
• /
• 2014

The acoustic cleaning system is widely used to remove foreign materials in factories, such as thermal power plants and incinerators. However, the acoustic cleaning systems tend to be clogged by foreign materials. In this paper, we develop a wireless sensor network for the sound wave detection in order to monitor proper operations in the acoustic cleaning systems. We observe that the developed wireless sensor network for the wave detection shows a stable operation in various industrial environments of wide temperature ranges. We also develop a data gathering device, which displays the current status of the sound generator and several values detected from the wireless sensor.