이 연구에서는 국내 피로설계규정상의 응력범주 C, D, E 및 E'에 해당하는 표준적인 구조인 십자 연결형, 면외거셋 부착형, 면내거셋 부착형 및 덮개판형을 모형화한 소형 시험편에 대한 피로실험을 실시하여 실험결과에 따라 각 시험편에 해당하는 국내 피로설계규정을 검증하며, 실험결과와 외국의 공개 데이터와의 비교 검토를 통해 국내 제작 강구조상세의 평가기준을 검토하였다. 실험 결과, AASHTO 및 JSSC, Eurocode의 관련 규정 값을 대부분 만족하는 것으로 확인되었다. 그러나, 십자연결형 접착부에 있어 모재가 파단된 하중전달형의 경우는 하중비전달형 보다 피로강도가 작으며, AASHTO 설계기준을 만족시키지 못하므로 설계기준에 대한 재검토가 필요할 것으로 판단된다. 한편, 요접부 길이의 영향은 면외거셋 에서 부착부 길이 80mm 시험편보다 150mm 시험편의 피로강도가 낮게 나타나 용접구조부 길이의 영향이 있음을 확인하였다. 실험결과들을 종합해보면, AASHTO 규정에 입각한 국내 시방서상의 피로규정을 대부분 만족하고 있으나, 보다 세분된 범주로 규정하고 있는 JSSC 및 Eurocode의 설계기준이 본 연구의 실험결과와 비교할 때 보다 합리적인 것으로 생각된다.
The objective of the study was to evaluate the use of n-alkanes to estimate DM intake and digestibility by beef cattle. Six steers were blocked (3 blocks, 2 animals/block) according to the body weight (279${\pm}$19 kg) and randomly allotted within blocks to two diets (3 steers/diet). A second trial was conducted with the same animals (321${\pm}$18 kg) after 36 days (d), using a switch back design. The diets consisted of two types of chopped sun-cured hay, alfalfa (Medicago sativa L) hay, or fescue (Festuca arundinacea Schreb) and alfalfa mixture, which were fed in equal amounts to steers. Animals were dosed with $C_{32}$ and $C_{36}$ alkanes, employing an intra-ruminal controlled-release device at the beginning of each trial. Hay intake per animal was measured from d 6 to 12 and sub samples were taken for chemical analysis. Rectal samples of feces were taken from each animal once/daily from d 8 to 14, freeze dried, and ground prior to alkane analysis. Alkanes were extracted from ground hay and feces. Feed intake was calculated from the dose rate of $C_{32}$ alkane and, the herbage and fecal concentrations of adjacent odd ($C_{33}$ or $C_{31}$) and even ($C_{32}$) chain length alkanes. Crude Protein, NDF, ADF, ash concentrations and In vitro dry matter digestibility (IVDMD) were 17.7, 42.2, 28.4, 7.9 and 71.7 for alfalfa, and 12.4, 56.5, 30.4, 6.9 and 69.1% for fescue/alfalfa mixture, respectively. For both diets, intake estimated from $C_{33}$:$C_{32}$ ratio was not different from the measured intake, but intake estimated from $C_{31}$:$C_{32}$ ratio was lower (p<0.05), than the measured intake for both diets. The average estimated forage intake from $C_{33}$:$C_{32}$ ratio was 4.86 and 0.69% below than the measured intake for alfalfa and, fescue/alfalfa mixed diets, respectively. The respective estimates with $C_{31}$:$C_{32}$ ratio were 9.59 and 11.33% below than the measured intake. According to these results, alkane $C_{33}$:$C_{32}$ ratio is better than alkane $C_{31}$:$C_{32}$ ratio for the estimation of intake by beef steers.
Operation of rice whiteners has been depending on operator's experience only and very limitted data are available for operational criteria of rice whiteners in Korea. With developments of new rice varieties and with a tendency of automation of machine operations for precision control, operational criteria depending on physical characteristics of rice grains arc required for an improvement of milled rice recovery and the performance of rice whitening systems. An experimental study was conducted to identify operational criteria of a rice whitening system consisted with an abrasive-aerated whitener developed newly and a frictional-aerated whitener being used commercially. Further, comparisons were made between the performance of the rice whitening system adopted for this study and a commercial system used in small scale milling plants. Results of this study are summarized as follows: 1. Total number of passes necessary for the final white rice in the combined whitening system depended exclusively on the counter pressure level of the frictional whitener successive to the abrasive whitener. 2. The counter pressure required for whitening Japonica type rice variety (Akibare) was higher by about 1.6 times than that for Japonica type (Pung-san), when other conditions were kept at the same. 3. Radial pressure in the whitening chamber of the frictional whitener should be maintained between 1.5 to $2.1kg/cm^2$ for the completion of whitening within 5 to 3 passes regardless of rice varieties. Hence, it was found that the radial pressure in the whitening chamber could be used as an operational criteria to control the counter pressure level. 4. The following regression equation was found between radial pressure($R_p$) in whitening chamber and electric power consumption of the whitening system: $$EPC=-0.545\;R^2_p+1.277\;R_p+0.874[KWH/100kg]$$ 5. The following multiple regression equation was found among radial pressure ($R_p$), counter pressure ($C_p$), and bioyield point ($B_i$), length (L) and width (W) of brown rice. $$R_p/(B_i/W^2)=0.547\{C_p/(B_i/W^2)\}^{0.365}(L/W)^{0.120}(R^2=0.9897)$$ 6. The milled rice recovery and machine efficiency (kg/KWH) from the combined whitening system were higher by about 2.0% point and by 15 to 27% point than those from the conventional system, respectively.
본 연구에서는 네일 삽입을 위한 천공작업 후, 공벽유지가 어려운 사질토 지반에 비교적 유리하게 적용할 수 있는 자천공방식의 스파이럴 파이프 네일링(SPN, Spiral Pipe Nailing) 시스템을 소개하고, 네일의 인장력 및 강성을 고려하여 안정성 평가를 하기위해 길이비($R_L$) 및 정착비($R_B$)를 다양하게 변화시켜가면서 간편시행쐐기법을 이용하여 한계평형해석을 수행하였다. 또한 FDM 수치해석 프로그램인 $FLAC^{2D}$ Ver. 3.30 프로그램을 사용하여, SPN 시스템 및 일반 쏘일네일링(GSN, General Soil Nailing) 시스템을 비교 평가하였다. 아울러 천공방법과 비트장착 등 SPN 시스템의 설계와 관련된 여러 인자에 대한 효과를 평가하기 위해, 6회의 변위제어방식 현장인발시험을 수행하였으며, 이를 토대로 SPN 시스템의 단기 인발거동특성을 평가해 보았다. 그 결과 SPN 시스템의 경우, GSN 시스템에 비해 강성, 인장강도 및 단위주면마찰력이 크게 발휘되므로, 전체안정성 측면에서 GSN 시스템에 비해 우수한 것으로 나타났다. 또한 강성을 고려한 간편시행쐐기법의 안정해석 결과를 살펴보면, 상용 한계평형해석 프로그램인 TALREN 97 프로그램의 안정해석 결과와 유사한 것으로 나타났다. 아울러 $FLAC^{2D}$ Ver. 3.30 프로그램 수치해석 결과를 살펴보면, SPN 시스템에서 유발되는 횡방향 변위의 경우, GSN 시스템에 비해, 10% 정도 감소하는 것으로 나타났다.
버켓기초는 현재 해양 구조물의 앵커나 해양 풍력발전의 기초로 광범위하게 쓰이고 있다. 그러나, 지금까지 버켓기초에 대한 설계 방법은 명확하게 제시되지 않았다. 그러므로, 본 연구에서는 범용 유한요소 해석 프로그램인 ABAQUS(2010)를 이용하여 점성토 지반에 설치된 버켓기초의 지지력 및 하중-변위거동에 대해 분석하였다. 버켓기초의 지지력에 영향을 주는 매개변수로 기초지름에 대한 근입깊이 비(L/D)를 선정하고 L/D 비를 0.25~ 1.0로 변화시키며 수직방향 압축과 수평방향의 지지거동을 분석하였다. 수치해석 결과 버켓기초의 지지력은 L/D비에 큰 영향을 받으며 L/D비가 0.25에서 1.0으로 증가함에 따라 수직방향 지지력은 약 40%, 수평방향 지지력은 약 90% 증가하는 것으로 나타났다. 수직하중이 작용하는 경우 버켓기초의 지지력은 깊은 기초와 유사하게 선단지지력과 주변마찰력을 분리하여 산정할 수 있었다. 그리고, 수평하중이 작용하는 경우 L/D비가 0.25 인 경우 기초의 수평이동 경향이 지배적이지만, L/D비가 0.5 이상으로 증가하면 기초의 회전파괴 경향이 지배적인 것으로 나타났다.
Lee, J.H.;Kim, J.H.;Kim, J.D.;Kim, S.W.;Han, In K.
Asian-Australasian Journal of Animal Sciences
/
제14권5호
/
pp.655-667
/
2001
This experiment was conducted to investigate the effect of feeding a low CP diet supplemented with synthetic amino acids on performance, nutrient utilization and carcass characteristics of finishing pigs fed under a three-phase feeding regimen. Ninety-six finishing pigs (Landrace$\times$Large White$\times$Duroc), $55.75kg{\pm}0.65$ of initial body weight, were blocked by weight and sex and allotted to four dietary treatments in a randomized block design. There were six pens per treatment and four pigs per pen. Pigs were fed a 16%-14%-12% CP (for phase I-II-III, respectively), sequence of diets. Dietary treatments were 1) Control, 2) Con+L (a sequence of diets reduced in CP by l percentage unit with lysine (L) supplementation, 3) Con+LMT (a sequence of diets reduced in CP by 2 percentage unit with LYS, methionine (MET) and threonine (THE) supplementation) and 4) Con+LMTT (a sequence of diets reduced in CP by 3 percentage unit with LYS, MET, THR and tryptophan (TRP) supplementation). The finishing period (55 to 105 kg) was divided into three phases (55 to 72 kg, 72 to 90 kg and 90 to 105 kg). Pigs fed either the control or Con+L diet grew faster (p<0.05) than pigs fed the Con-LMT or Con+LMTT diet. There was no difference in ADFI among dietary treatments. Phosphorus (P) digestibility was lowest in the control group and highest in the Con+LMTT group (p<0.05). Within each phase, no significant differences in dry matter (DM) and CP digestibilities were found. Although some amino acid digestibilities were affected by dietary treatments, digestibilities of essential amino acids (EAA), non-essential amino acids (NEAA) and total amino acid were not significantly influenced by dietary treatments. For the entire experiment periods, Con+L, Con+LMT and Con+LMTT treatments resulted in 13.4, 18.8 and 21.6% lower total N excretion compared with the control. Con+LMT and Con+LMTT treatments showed significantly lower BUN concentration compared with the control and Con+L treatment (p<0.05), but there was no significant difference in BUN concentration between pigs fed the control and Con+L treatment or between pigs fed Con+LMT and Con+LMTT treatments (p>0.05). Carcass length, backfat thickness and carcass grade were not significantly affected by dietary treatments (p>0.05). In conclusion, reducing dietary CP level by 1 percentage unit and supplementing only LYS at each phase could be a very beneficial feeding strategy for finishing pigs fed under a three phase feeding regimen in terms of both environmental and economical aspects.
Effects of particle size and physical effective fibre (peNDF) of rice straw in diets on chewing activities, feed intake, flow, site and extent of digestion and rumen fermentation in goats were investigated. A 4${\times}$4 Latin square design was employed using 4 mature Liuyang black goats fitted with permanent ruminal, duodenal, and terminal ileal fistulae. During each of the 4 periods, goats were offered 1 of 4 diets that were similar in nutritional content but varied in particle sizes and peNDF through alteration of the theoretical cut length of rice straw (10, 20, 40, and 80 mm, respectively). Dietary peNDF contents were determined using a sieve for particle separation above 8 mm, and were 17.4, 20.9, 22.5 and 25.4%, respectively. Results showed that increasing the particle size and peNDF significantly (p<0.05) increased the time spent on rumination and chewing activities, duodenal starch digestibility and ruminal pH, and decreased ruminal starch digestibility and $NH_{3}$-N concentration. Intake and total tract digestibility of nutrients (i.e. dry matter, organic matter, and starch) and ruminal fermentation were not affected by the dietary particle size and peNDF. Increased particle size and peNDF did not affect ruminal fibre digestibility, but had a great impact on the intestinal and total tract fibre digestibility. The study suggested that rice straw particle size or dietary peNDF was the important influential factor for chewing activity, intestinal fibre and starch digestibility, and ruminal pH, but had minimal impact on feed intake, duodenal and ileal flow, ruminal and total tract digestibility, and ruminal fermentation.
본 논문은 자동차용 타이어 공기압 모니터링 시스템(TPMS)의 핵심 부품인 가속도센서에 관한 연구이다. 일반적으로 압저항형 가속도센서는 정전용량형 가속도센서에 비하여 제조 비용이 적고 출력 특성이 선형적이며 주변 잡음에 면역성이 강한 장점을 갖는다. 그래서 TPMS용으로 압저항형을 선택하였고, ANSYS 프로그램을 이용하여 3가지 타입의 구조를 설계하여 공진주파수 특성을 비교하여 가장 안정적인 구조인 질량체 가장자리의 가운데에 있는 4개의 빔에 의하여 지지되는 브릿지 타입의 실리콘압저항형 가속도센서를 선택하였다. 그리고 센서 크기를 고려하여 빔의 길이는 $200{\mu}m$로 정하였으며, 빔 길이에 따른 최대응력과 최대변위를 시뮬레이션하여 센서를 설계하였다. TPMS용 4 빔 실리콘 미세 압저항형 가속도센서의 크기는 $3.0mm{\times}3.0mm{\times}0.4mm$의 크기로 제작 되었다. 휠 각도에 따른 출력 특성과 온도 특성을 측정하여 센서의 특성을 분석 하였다. 그 결과 가속도센서의 옵셋 전압은 43.2 mV 이고 감도는 $42.5{\mu}V/V/g$ 이다. 센서의 특징으로 내충격성은 1500 g 이고, 측정 범위는 0 ~ 60 g, 사용온도는 $-40^{\circ}C{\sim}125^{\circ}C$ 를 갖는다.
본 연구에서는 94 GHz 송수신 시스템에 응용이 가능한 평면형 회로 내의 전송 선로 방식의 하나인 CPW(Coplanar Waveguide)와 구형 도파관 간의 신호를 원활히 전달해주는 94 GHz CPW-구형 도파관 변환기를 설계하고 제작하였다. 제안된 변환기는 단일 면에 구현된 Fin-line 테이퍼와 Open 타입의 CPW-Slot-line 변환기 구조로 구성되어 있으며, 이는 MMIC의 플립칩 본딩을 위해 기존의 MMIC 기술을 이용하여 단단하고 구부러지지 않는 사파이어($Al_2O_3$)기판위에 구현되었다. Ansoft사의 HFSS 툴을 이용하여 최적화된 Single-section 변환기를 Back-to-back 구조의 지그로 제작하였고 Anritsu ME7808A Vector Network Analyzer 장비를 이용해 $85{\sim}105$ GHz를 대역에서 S-파라미터들을 측정하였다. 측정 결과, 3 mm 길이를 갖는 CPW의 삽입 손실을 고려하여 94 GHz에서 약 1.7 dB의 삽입 손실과 25 dB 이상의 반사손실을 확인 하였다.
잣송이 수확기계의 개발을 위한 기초자료를 얻기 위하여 강원대학교 임과대학 부속연습림에서 7영급 및 4영급의 착과한 잣나무의 정단부위 성장특성과 착과특성을 1992년 8월 말부터 9월 중순까지 조사하였다. 1. 당년 성장한 가지의 길이는 4영급에서 주지는 27~56cm이고 측지는 18~47cm로 7영급보다 훨씬 왕성하였다. 2. 측지의 분지각은 $24{\sim}89^{\circ}$이었고, 2년 성장한 주지의 직경은 10~30mm로서 두 특징에 있어 영급간 유의적인 차이가 없었으나, 1년생 주지의 직청은 4영급에서 9~18mm로서 7영급보다 생장량이 더 높았다. 3. 착과수는 평균 5개, 구과 생중량은 평균 272g으로 영급간 유의적인 차가 없었다. 4. 2년 자란 주지의 착과위치는 그 마디 아랫 쪽으로부터 7영급에서는 9.7~33.0cm, 4영급에서는 18.0~51.0cm의 범위인 곳으로 평균위치는 각 마디의 1/2과 4/5되는 위치였다. 5. 착과한 나무에 있어서 구과, 1년생지 및 2년생지를 합한 총생중량의 범위는 1.0~7.4kg이었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.