• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.53-61
• /
• 2014

In this paper, we present the design, fabrication and measurement of high efficiency GaN HEMT power amplifier using harmonic matching technique. In order to achieve high efficiency, harmonic load-pull simulation is performed, that is, the optimum load impedances are determined at $2^{nd}$ and $3^{rd}$ harmonic frequencies as well as at the fundamental. Then, the output matching circuit is designed based on harmonic load-pull simulation. The measurement of the fabricated power amplifier shows the linear gain of 20 dB and $P_{1dB}$(1 dB gain compression point) of 33.7 dBm at 1.85 GHz. The maximum power added efficiency(PAE) of 80.9 % is achieved at the output power of 38.6 dBm, which belongs to best efficiency performance among the reported high efficiency power amplifiers. For W-CDMA input signal, the power amplifier shows a PAE of 27.8 % at the average output power of 28.4 dBm, where an ACLR (Adjacent Channel Leakage Ratio) is measured to be -38.8 dBc. Digital predistortion using polynomial fitting was implemented to linearize the power amplifiers, which allowed about 6.2 dB improvement of an ACLR performance.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.40-45
• /
• 2013

Satellite's infrared detector shall be calibrated under thermal vacuum environment using a reference black body before a launch. The full aperture black body (FABB) as an infrared calibration reference shall be composed of vacuum compatible materials and temperature controlled from $-40^{\circ}C$ to $+40^{\circ}C$ with emissivity higher than 0.95. The temperature homogeneity over the central 80 % area of the FABB front surface shall be better than 2 K. The FABB designed by thermal and flow analysis was $1m{\times}1m{\times}8mm$ copper plate on which black painted aluminum honeycomb core was attached. Copper tubes were welded on the opposite side of the honeycomb core to allow temperature regulated gaseous nitrogen to flow through them. By the FABB validation test, the temperature homogeneity was observed around 1 K using 20 PT100 sensors and modified COTS infrared camera. The emissivity value was 0.975 at $40^{\circ}C$ under atmospheric pressure.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.208-215
• /
• 2021

In this study, a customiz ed bridge system was developed for North Korea application. For the application of North Korea, the customized bridge system design, fabrication, and construction performance evaluation were performed using ultra-high performance concrete a compressive strength 120MPa or more and a direct tensile strength 7MPa or more. The comparison of the North Korean truck luggage load(30, 40, 55) and the Korean standard KL-510 load showed that cross-section increased as the load increased. Furthermore, a bridge with a span length of 30m was fabricated with ultra-high performance concrete for the construction performance evaluation. The evaluation of the load condition analysis was performed by a flexural test. The results showed that a bridge with a span length of 30m secured about 167% of sectional performance under initial cracking load conditions and about 134% of load bearing capacity under ultimate load conditions. As a result of economic analysis, the customized bridge system using ultra-high-performance concrete was less than about 11% of the upper construction cost compared to the steel composite girder bridge. Therefore, these results suggest that the price competitiveness can be secured when applying the ultra-high-performance concrete long-span bridge developed through this study.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.512-518
• /
• 2019

To develop a membrane electrode assembly (MEA) with lower Pt loading and higher performance in proton exchange membrane fuel cells (PEMFCs), it is an important research issue to understand interfacial structure of Pt/C catalyst and ionomer and design the catalyst layer structure. In this study, we prepared short-side-chain Nafion-based ionomer dispersion using propylene glycol (PG) as a solvent instead of water which is commonly used as a solvent for commercially available ionomers. Cathode catalyst layers with different ionomer content from 20 to 35 wt% were prepared using the ionomer dispersion for the fabrication of four different MEAs, and their fuel cell performance was evaluated. As the ionomer content increased to 35 wt%, the performance of the prepared MEAs increased proportionally, unlike the commercially available water-based ionomer, which exhibited an optimum at about 25 wt%. Small size micelles and slow evaporation of PG in the ionomer dispersion were effective in proton transfer by inducing the formation of a uniformly structured catalyst layer, but the low oxygen permeability problem of the PG-based ionomer film should be resolved to improve the MEA performance.

• Advanced Industrial SCIence
• /
• v.2 no.2
• /
• pp.9-15
• /
• 2023

Since silicone rubber heaters are flexible, they can be directly attached or installed in objects to be heated even in flat, curved or three-dimensional shapes. Since the current heating method heats the entire object to be heated and raises it to a required temperature, ignoring areas or positions where heat is not required, partial intensive heating cannot be performed. When using multi-heating zones, rather than heating the entire object to be heated, only the parts that need heat are intensively heated according to the process, so it is possible to heat quickly by local location by applying different amounts of heat with a small amount of electric capacity to each place that needs heat, and heat energy can reduce. In this study, the temperature and heating time of the partially concentrated region in the multi-heating region structure are measured so that a uniform temperature or temperature difference occurs in the region requiring thermal fusion. In order to determine the optimal power density range and reduce capacitance, the safety of a silicon rubber heater manufactured with a multi-heating zone structure is investigated. If the silicon rubber heater is manufactured in a multi-heating method, the multi-intensive heating technology can be ideally applied to all heating processes.

• Advanced Industrial SCIence
• /
• v.3 no.2
• /
• pp.31-37
• /
• 2024

This paper presents a single and 2-patch microstrip array antenna operated on a frequency of 10.3GHz(x-band). It outlines the process of designing a microstrip patch array antenna using CST MWS. Initially, a single microstrip antenna was designed, followed by optimization using CST MWS to attain optimal return losses and gain. Subsequently, the design was expanded to create a 2×1 microstrip inset-fed array antenna for the X-band applications. The construction material is Roger RO4350B, with specific dimensions (h=0.79mm, 𝜖_r = 3.54). The achieved results include an S11 of -18dB at the resonant frequency (10.3GHz), a gain of 9.82dBi, a bandwidth of 0.165GHz, and a 3-dB beamwidth of 30°, 121° in Az(𝜑=0) and El(𝜑=90) plane, respectively. The future plan involves the fabrication of this array antenna and further expansion to a 4×4 array of microstrip antennas. It is then incorporated on the X-band applications for practical uses.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.11A
• /
• pp.1661-1671
• /
• 2000

본 고에서는 한국통신(Korea Telecom) IMT-2000 시험시스템(이하: Trial system 라고 함) 단말기용 전력증폭단으로 적용하기 위한 다단구동증폭기 및 전력증폭기를 GaAs MMIC로 설계 구현하는 기술을 제시하였다. 설계된 구동증폭기는 3단으로구성하여 RF(Radia Frequency) 송신신호(1955$\pm$70MHz)대역에서 2단 (중간단)의 이득 조정범위가 40 dB이상이 될 수 있도록 능동부품인 MESFET를 Cascade 형으로 구성하고 MESFET의 게이트(gate)에 조정전압을 인가하는 증폭기를 설계하여 GaAs MMIC화 1 침(크기4$\times$5 mm)으로 제작하였다. 아울러, 본 논문에서는 제시한 구동증폭기는 동작주파수 대역폭 범위기 3.5배이고 출력전력은 15dBmm 이며, 출력전력이득이 25~27dB이고 반사계수는 -15~20dB이며 이득평탄도 3dB(동작주파수 대역폭내)로써 Trial system용 단말기의 최종단인 전력증폭단의 출력단 특성을 효과적으로 나타내었다. 그리고, 전력 증폭기는 2개의 입력단에서 출력되는 신호를 분배하는 전력분배기와 병렬구조인 4개의 증폭단에서 출력되는 출력신호를 외부에서 접속하는 전력결합기를 접소하여 구성하였으며 RF(Radio Frequency) 주파수(1955 $\pm$70NHz)에서 대역폭을 4배로 설계하여 광대역인 대역폭을 구현하였고 출력전력은 570mW이며, 출력부가효율(PAE; Power Added Efficency)가 -15$\pm$20dB이고, 이득 평탄도(Gain flatness)는 동작주파수 대역내에서 0.5dB이며 입출력 전압정재파비(Input & Output VSWR)가 13이하인 고출력 전력증포기를 GaAs MMIC화 1칩 (크기; 3$\times$4mm)으로 제작하였다.의 다양성이나 편리성으로 변화하는 것이 국적을 바꾸는 것보다 어려운 시 대가 멀지 않은 미래에 도래할 것이다. 신세기 통신 과 SK 텔레콤에는 현재 1,300만명이 넘 는 고객이 있으며. 이들 고객은 어 이상 음성통화 중심의 이동전화 고객이 아니라 신세기 통신과 SK텔레콤이 함께 구축해 나갈 거대란 무선 네트워크 사회에서 정보화 시대를 살아 갈 회원들이다. '컨텐츠의 시대'가 개막되는 것이며, 신세기통신과 SK텔레콤은 선의의 경쟁 과 협력을 통해 이동인터넷 서비스의 컨텐츠를 개발해 나가게 될 것이다. 3배가 높았다. 효소 활성에 필수적인 물의 양에 따른 DIAION WA30의 라세미화 효율에 관하여 실험한 결과, 물의 양이 증가할수록 그 효율은 감소하였다. DIAION WA30을 라세미화 촉매로 사용하여 아이소옥탄 내에서 라세믹 나프록센 2,2,2-트리플로로에틸 씨오에스터의 효소적 DKR 반응을 수행해 보았다. 그 결과 DIAION WA30을 사용하지 않은 경우에 비해 반응 전환율과 생성물의 광학 순도는 급격히 향상되었다. 전통적 광학분할 반응의 최대 50%라는 전환율의 제한이 본 연구에서 찾은 DIAION WA30을 첨가함으로써 성공적으로 극복되었다. 또한 고체 염기촉매인 DIAION WA30의 사용은 라세미화 촉매의 회수 및 재사용이 가능하게 해준다.해준다.다. TN5 세포주를 0.2 L 규모 (1 L spinner flask)oJl에서 세포간의 응집현상 없이 부유배양에 적응,배양시킨 후 세포성장 시기에 따른 발현을 조사한 결과 1 MOI의 감염조건 하에서는 $0.6\times10^6$cell/mL의 early exponential시기의 세포밀도에서 72시간 배양하였을 대 최대 발현양을 나타내었다. 나타내었다. $\beta$4 integrin의 표현이 침투 능력을 높이는 역할을 하나 이때에는 laminin과 같은 리간드와의 특이

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.1
• /
• pp.116-125
• /
• 2021

A three-dimensional (3D) intraoral scanner, which is one of the major developments in digital dentistry, is widely used in fixed prosthodontics. The application of intraoral scanner is now increasing in removable prosthodontics. Sclerotic change induced by scleroderma causes the limitation of mouth opening and multiple loss of the teeth. Conventional prosthodontic procedures are challenging for patients with this disease. This study showed a case of digital approach to the removable prosthodontic treatment of a patient who had the scleroderma and the consequent microstomia. At the provisional stage, the optical impression of patient's oral structures was digitally obtained. Using a 3D printer, the provisional dentures were fabricated. After extraction of hopeless tooth, the definitive digital impression was taken and the metal frameworks were fabricated, based on the data acquired from the impression. The definitive removable partial dentures were completed and delivered to the patient, who was satisfied with the prostheses.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.351-357
• /
• 2022

In this study, offshore modular pier system using the ultra-high performance concrete was developed for the offshore construction environment. For the application of offshore modular pier system, the design, fabrication, and construction performance evaluation were performed using ultra-high performance concrete a compressive strength 120 MPa or more and a direct tensile strength 7 MPa or more. For offshore piers previously constructed with precast concrete, it was intended to verify the idea and possibility of solving errors due to position or vertical deformation during the driving of the foundation pile part during the construction stage. Furthermore, a offshore modular pier system was fabricated with ultra-high performance concrete for the construction performance evaluation. The results showed that a offshore modular pier system secured about 9 % of sectional performance of load bearing capacity under ultimate load conditions. If the offshore modular pier system developed through this study is utilized in the future, it is judged that competitiveness due to sufficient durability and constructability can be secured.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.52-59
• /
• 2007

In this paper, we analyzed and measured implant isolation characteristics for a 1.25 Gbps monolithic integrated hi-directional (M-BiDi) optoelectronic system-on-a-chip, which is a key component to constitute gigabit passive optical networks (PONs) for a fiber-to-the-home (FTTH). Also, we derived an equivalent circuit of the implant structure under various DC bias conditions. The 1.25 Gbps M-BiDi transmit-receive SoC consists of a laser diode with a monitor photodiode as a transmitter and a digital photodiode as a digital data receiver on the same InP wafer According to IEEE 802.3ah and ITU-T G.983.3 standards, a receiver sensitivity of the digital receiver has to satisfy under -24 dBm @ BER=10-12. Therefore, the electrical crosstalk levels have to maintain less than -86 dB from DC to 3 GHz. From analysed and measured results of the implant structure, the M-BiDi SoC with the implant area of 20 mm width and more than 200 mm distance between the laser diode and monitor photodiode, and between the monitor photodiode and digital photodiode, satisfies the electrical crosstalk level. These implant characteristics can be used for the design and fabrication of an optoelectronic SoC design, and expended to a mixed-mode SoC field.