• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.7
• /
• pp.307-314
• /
• 2003

This paper presents a 3D shape optimization algorithm for electromagnetic devices using the design sensitivity analysis with finite element method. The structural deformation analysis based on the deformation theory of the elastic body under stress is used for mesh renewing. The design sensitivity and adjoint variable formulae are derived for the 3D finite element method with edge element. The results of sensitivity analysis are used as the input data of the structural analysis to calculate the relocation of the nodal points. This method makes it possible that the new mesh of analysis region can be obtained from the initial mesh without regeneration. The proposed algorithm is applied to the shape optimization of 3D electromagnet pole to net a uniform flux density at the target region.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.6
• /
• pp.441-451
• /
• 2007

In this paper, the method to modify a surface through three dimensional vector field technique is presented, In this method two guide surfaces are required as a shape reference. One is the shape of original surface, the other is the target shape for the result surface. Proposed method is consists of two steps. The first step is to calculate the mapping points on original and target guide surfaces so that the shape error may be minimized. The second step is to construct the smooth vector field from mapping points of the first step. The developed method is applied to shoe design system which makes the surface modeling very easy and effective.

• 연구논문집
• /
• s.33
• /
• pp.89-97
• /
• 2003

A barrel cam is used as a very important part of an index drive unit. The index drive unit must have an intermittent-rotational motion. The barrel typed cam and roller gear mechanism has the advantages of high reliability to perform a prescribed motion of a follower. This paper proposes a new method for the shape design of the barrel cam and also a CAD program is developed by using the proposed method. As defined in this paper, the relative velocity method for the shape design calculates the relative velocity of the follower versus cam at a center of roller, and then detemines a contact point by using the geometric relationships and the kinematic constraints, where the direction of the relative velocity must be parallel to a common tangential line at the contact point of two independent bodies, i.e. the cam and the follower. Then, the shape of the cam is defined by the coordinate transformation of the trace of the contact points. This paper presents shape design of the barrel cam in order to prove the accuracy of the proposed methods

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.1
• /
• pp.23-32
• /
• 1998

A shape estimation is needed to control actively a smart structure. A method is, hence, proposed to predict the deformed shape of the structure subjected to unknown external load using the signal from sensors attached to the structure. The shape estimation is based on the relationship between the deformation of the structure and the signal from the sensors. The matrix containing the relationship between the deformation and signal is obtained using fictitious force or eigenvector of global stiffness matrix. Then the deformed shape can be predicted using the linear matrix and signal from sensors attached to the structure. To verify this method, experiment and FEM were performed and it was shown that the shape estimation method based on the fictitious force predicts deflections well and more accurately than that based on eigenvector.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.29-33
• /
• 2012

A 3D scanner scans and captures the shape of a real-world object. The captured shape can be used to construct three-dimensional model for CAD/CAM applications. In this study we have tried to design a cell phone cover by using the 3D scanner and reverse engineering. A 3D scanner is used to capture the shape of a cell phone. The 3D scanner generates a point cloud as the shape information. A three-dimensional CAD model for the cell phone is constructed from the point cloud. A cell phone cover is designed based on the CAD model of the cell phone. To check the integrity of this design process a prototype of the cover is made and assembled with the cell phone.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.29 no.5
• /
• pp.84-91
• /
• 2001

The purpose of this thesis is to search for appropriate design elements to manage ponds on golf courses. This paper showed that a variable, width, and volume have significant influence on satisfaction(Sig 0.001). This research investgated golf courses in Kyung-ki province. In short, we measured the physical design elements of ponds to bring out major factors which could determine satisfaction of golf courses for golfcourse manager(greenkeeper). The results between satisfaction and physical variable came out as follows; 1, Golfcourse managers(Green keepers) responded to questions that they were satisfied in only 29.9% of the ponds. We found that they considered management very highly. we could evaluated the value of necessity and importance are high, that is importance to manage ponds 2. Some physical design elements(volume, width) increased dependent variable(satisfaction) and others(length, area, circumference, index of shape) decreased dependent variable(satisfaction) 3. Volume has an influence on dependent variable more than depth on index of shape. 4 If the result of \`index of shape\` decreased, the result of \`management satisfaction\` would be high, and when volume is 8500ton∼17000ton, depth is 27m∼3.1m, \`management satisfaction\` would be high. The research findings can be used for planning and designing of golfcourses for designers, and by management for greenkeepers, and will provide pertinent design elements far design of golfcourses. We suggest that the interrelation between ponds and strategic play must be examined in future research.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.11
• /
• pp.1151-1157
• /
• 2009

Ensuring both product quality and reducing material cost are important issue for the design of the piping system of an air conditioner outdoor unit. This paper describes a shape optimization that achieves mass reduction of an air conditioner piping system while satisfying two design constraints on resonance avoidance and the maximum stress in the pipes. In order to obtain optimized design results with various analysis fields considered simultaneously, an automated multidisciplinary analysis system was constructed using PIAnO v.2.4, a commercial process integration and design optimization(PIDO) tool. As the first step of the automated analysis system, a finite element model is automatically generated corresponding to the specified shape of the pipes using a morphing technique included in HyperMesh. Then, the performance indices representing various design requirements (e.g. natural frequency, maximum stress and pipe mass) are obtained from the finite element analyses using appropriate computer-aided engineering(CAE) tools. A sequential approximate optimization(SAO) method was employed to effectively obtain the optimum design. As a result, the pipe mass was reduced by 18 % compared with that of an initial design while all the constraints were satisfied.

• Transactions of Materials Processing
• /
• v.14 no.2 s.74
• /
• pp.126-132
• /
• 2005

The isothermal forging design of a Ti-6Al-4V wing shape was performed by 3D FE simulation. The design focuses on near-net shape forming by the single stage. The process variables such as the die design, pre-form shape and size, ram speed and forging temperature were investigated. The main design priorities were to minimize forging loads and to distribute strain uniformly in a given forging condition. The FE simulation results for the final process design were compared with the isothermal forging tests. The instability of deformation was evaluated using a processing map based on the dynamic materials model(DMM), including flow stability criteria. Finally, a modified process design for producing a uniform Ti-6Al-4V wing product without forming defects was suggested.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.66-71
• /
• 2021

In this study, the shape design optimization of a refrigerator door hinge stopper was performed to reduce the discrepancy in the opening forces of the left and right doors of a double-door refrigerator. A finite element model was constructed and analyzed by quasi-static analyses to evaluate the structural performance of the door hinge stopper. The reaction moment calculated at the hinge axis was used as a measure of the door opening and closing forces. The design objective is to increase the door opening force by 50% while maintaining the door closing force and the maximum stress calculated in the body of the hinge stopper at the current level. A new design concept with a contacting slot was proposed to decouple the door closing and opening forces. Shape optimization was performed to determine the dimensions of the new design of the hinge stopper, and the rib pattern was determined by topological optimization to further increase the door opening force. It was observed that the new design met all design requirements.

• Fashion & Textile Research Journal
• /
• v.24 no.4
• /
• pp.443-450
• /
• 2022

This study developed a three-dimensional helmet mold design software that can design helmets for treating the infant plagiocephaly (flat head syndrome) using three-dimensional head scan data. For this, the three-dimensional head data of sixth SizeKorea body measurement project as well as the data produced by a head modeling software were used to prepare the head shape data of plagiocephaly patients. A total of 14 landmarks and 10 dimensions of heads required for helmet mold shape design and plagiocephaly diagnosis were automatically measured using an anthropometric analysis software. Using the software developed in this study, plagiocephaly can be diagnosed not only visually by three-dimensional head data visualization but also quantitatively by calculating the medically defined indices such as cranial index, which measures the proportions of the head, and the cranial vault asymmetry index, which measures the asymmetry of the head. The basic shape of the helmet mold was automatically generated based on the head scan data. Additionally, it is possible to fine tune the shape of the mold to reflect individual characteristics by using a free form deformation technique. Finally, the designed helmet mold was converted into the data that can be printed on a three-dimensional printer for generating the actual prototype.