• Journal of Biosystems Engineering
• /
• 제22권2호
• /
• pp.105-116
• /
• 1997

Using the design variables and conditions reported in the rut part of this paper, an analysis and optimum design of the tractor-rotary power driveline were carried out. The optimum design method involved 1 variable, 2 variable and multiple variable analysis performed as requested in the design process. In order to evaluate the effects of the design variables on the power transmission performance a sensitivity analysis were also conducted. the results indicated that the length and link point of the upper link, the upper hitch point of the implement master and the location of the implement input connection affect most significantly the driveline performance. The optimum design improved the performance of an exampled tractor-rotary driveline by 93% in terms of cosine ratio.

• 한국유체기계학회 논문집
• /
• 제19권6호
• /
• pp.34-42
• /
• 2016

The organic Rankine cycle (ORC) has been used to convert thermal energy to mechanical energy or electricity. The available thermal energy could be waste heat, solar energy, geothermal energy, and so on. However, these kinds of thermal energies cannot be provided continuously. Hence, the ORC can be operated at the off-design point. In this case, the performance of the ORC could be worse because the components of the ORC system designed based on a design point can be mismatched with the output power obtained at the off-design point. In order to improve the performance at the off-design point, a few components were replaced including generator, bearing, load bank, shaft, pump and so on. Experiments were performed on the same facility without including other losses in the experiment. The experimental results were compared with the results obtained with the previous model, and they showed that the system efficiency of the ORC was greatly affected by the losses occurred on the components.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1423-1431
• /
• 2001

Based on the exponential intervening variable, a new two-point approximation method is presented. This introduces the shifting level into each exponential intervening variable to avoid the lack of def inition of the conventional exponential intervening variables due to zero-or negative-valued design variables. Then a new quadratic approximation whose Hessian matrix has only diagonal elements of different values is proposed in terms of these intervening variables. These diagonal elements are determined in a closed form that corrects the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the previous point. Finally, in order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve six typical design problems. These optimization results are compared with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• 복식문화연구
• /
• 제9권6호
• /
• pp.893-907
• /
• 2001

The main purpose is to study the effects of princess lines on different body types and to disguise any imperfection by using diverse princess lines. We separated testers body shapes into specific body types, H, Y by applying both the direct and the indirect measurements. These designs were evaluated by using the point ranking system method, and then average scores were obtained from these evaluations. Following are the results of the study: 1 These are the resulting illusion effects when the shoulder width of the Princess line was fixed. When the Princess line originated from 1/3 point of the armhole, body types Y appeared to show narrow waist width. A-line silhouette appeared to display the narrowest shoulder width. When the Princess line originated from 2/3 point of the armhole, body types H and Y appeared to exhibit narrowest waist widths, and the A-line silhouette once again displayed the narrowest shoulder width. When the Princess line originated from 1/2 point of the armhole, body type H appeared to exhibit narrow width; and H-line silhouette displayed the narrowest shoulder width 2. When the Princess lines waist w'4th was fixed in order to study illusion effects of waist widths. In this experiment, locations of Princess lines and widths of the skirt were varied. When the waist width was fixed at 6.5 cm, For the H body type, the Princess line location of 1/3 point of the armhole in H-line silhouette design exhibited the narrowest waist width. For the Y body type in A-line silhouette design, the Princess line locations of 1/3 and 1/2 points of the armhole exhibited the narrowest waist width because it displayed the hourglass effect. When the waist width was fixed at 10 cm, H body type did not exhibit any significant differences between designs. For Y body type, A-line silhouette design with the Princess line origination point at 1/3 down the armhole exhibited the narrowest waist width. 3. The illusion effects of the hip were studied by fixating the width of the skirt and varying the locations of Princess line and waist widths. In H-line skirt silhouette designs, all two body types exhibited narrow hips when the Princess line origination points were at 1/3 and 1/2 way down the armhole. For A-line skirt silhouette, H body type exhibited narrow hips when narrow waist design with the Princess line originating from 1/2 point in the shoulder was shown. Y body type exhibited narrow hips when narrow waist design with the Princess line originating from 1/3 point of the armhole and 2/3 point of the shoulder. 4. With both waist and skirt widths fixed, all two body types exhibited taller and slender postures when the Princess line originated from the shoulder compare to the armhole.

• 한국CDE학회지
• /
• 제16권2호
• /
• pp.2-7
• /
• 2010

• 한국식품영양학회지
• /
• 제31권2호
• /
• pp.272-277
• /
• 2018

This research was conducted to elucidate the optimum conditions for the antibacterial activity of konjak jelly using the evolutionary operation-factorial design technique. In the first set of experiments, concentration of a coagulation agent, soaking liquid, and temperature of water were set to 0.4%, $0.6{\times}10^{-2}N$, and $65^{\circ}C$ as a central point, respectively. The highest antibacterial activity was acquired at E21, in which the number of bacteria was 1.25 log cfu/g. Because the code of changes in the main effect was (-), it could be decided that the central point of the first set was not the optimum point. Although antibacterial activity in the second set was improved, the values of the main effect were higher than that of changes in the mean effect. The central point of third set was concentration of coagulation agent 0.8%, concentration of soaking liquid $1.0{\times}10^{-2}N$, and temperature of water $65^{\circ}C$. It was found that the antibacterial activity of central point in the third set was highest among all the tested set. Further, all the necessary conditions were appropriate to reach the optimum condition. The antibacterial activity of the central point in third set was more than 1,000 times higher than that of E11, in first set.

• 한국디자인학회:학술대회논문집
• /
• 한국디자인학회 2004년도 추계 학술발표대회 논문집
• /
• pp.216-217
• /
• 2004

• 한국디자인학회:학술대회논문집
• /
• 한국디자인학회 2003년도 가을학술발표대회
• /
• pp.32-33
• /
• 2003

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.670-675
• /
• 2001

This paper describes aerodynamic preliminary design performance prediction and flow analysis for turbine of the marine middle engine turbocharger. The performance characteristics of turbocharger turbine are investigated at various operating conditions using mass flow rate and computational flow analysis for rotor and nozzle at design point are performed. Preliminary design results are performed by applying mean line and radial equilibrium theory. Performance prediction and flow analysis results show good agreement with experiments. From 3 dimensional flow analysis result, efficiency is 0.6% greater than design point. Therefore, this design approach is useful for preliminary design, and helps to increase the design capability for optimized rotor blade.

• 한국디자인학회:학술대회논문집
• /
• 한국디자인학회 2005년도 춘계 학술발표대회 논문집
• /
• pp.312-313
• /
• 2005