• 한국안전학회지
• /
• 제8권1호
• /
• pp.47-53
• /
• 1993

Residual Deformation Analysis(RDA) is a new method for ratings of the continuous bridges. The RDA makes it possible to expand the inelastic steel girder bridge design method set forth in the American Association of State Highway Officals'(AASHTO) Guide Specifications for Alternate Load Factor Design Procedures for Steel Beam Bridges Using Braced Compact Sections(1986) into an inelastic rating method. It is a method to assess the residual moments and deformations that are set up in a beam that has been loaded into the post-elastic range This method combines classical elastic conjugate beam theory with linear moment-rotation relationships for midspan inelastic positive moment. The limit state is inelastic serviceability limit. which is defined as the ratio of the span to midspan inelastic deflection(C=L/D).

• 농업과학연구
• /
• 제43권4호
• /
• pp.656-664
• /
• 2016

Gear reducers are widely used for various agricultural machinery applications such as greenhouses, tractors, and agricultural vehicles. However, thermal deformation and surface pitting at gear tooth flank frequently occur in gear reducers due to high torque. Thus, surface heat treatment of gears is required to improve wear and fatigue resistance. The objective of this study was to simulate the load capacity of the agricultural gear reducer. The simulation was performed for the following three surface heat treatment methods: untreated gears, nitriding heat treatment, and induction hardening method, those mostly used for agricultural gear reducers. The load capacity of the gear reducer was simulated using the safety factor, limit bending stress, and limit contact stress of the gear. The simulation of the load capacity was conducted using KISSsoft commercial software for gear analysis. The main results of simulation test were as follows: first, the nitriding heat treatment resulted in the highest safety factor for bending stress, which was increased about 77% from those of the untreated gears. Second, the induction hardening was the highest safety factor for contact stress, which was increased about 150% from those of the untreated gears. The safety factor for contact stress of the induction hardening was increased about 64% from those of the nitriding heat treatment. The study result suggested that the surface heat treatments could enhance load capacity and that the method of surface heat treatment should be determined based on simulation results for appropriate use scenarios.

• Computers and Concrete
• /
• 제33권4호
• /
• pp.373-384
• /
• 2024

In this study, a novel mountain train system was developed that can run along a steep gradient of 180 ‰ and sharp curve with a minimum radius of 10 m. For this novel mountain train, an embedded precast concrete rack rail track was implemented to share the track with an automobile road and increase constructability in mountainous regions. The embedded rack rail track is connected to a hydraulically stabilized base (HSB) layer with shear anchors, which must have sufficient longitudinal resistance because they bear most of the traction forces originated from the rack rail and longitudinal loads owing to the steep gradient. In addition, the damage to the shear anchor parts, including the surrounding concrete, must be strictly limited under the service load because the maintenance of shear anchors inside the track is extremely difficult after installation. In this study, the focus was made on the shear anchor behavior and design an embedded rack rail track, considering the serviceability and ultimate limit states. Accordingly, the design loads for mountain trains were established, and the serviceability criteria of the anchor were proposed. Subsequently, the resistance and damage of the shear anchors were evaluated and analyzed based on the results of several finite element analyses. Finally, the design method of the shear anchors for the embedded rack rail track was established and verified.

• Steel and Composite Structures
• /
• 제12권6호
• /
• pp.523-540
• /
• 2012

It was clear from the former researches on reinforced concrete filled tubular steel (RCFT) structures that RCFT structures have different performance than concrete filled steel tubular (CFT) structures. However, despite of that, load-sharing ratio of RCFT is evaluating by the formula and range of CFT given by JSCE. Therefore, the aim of this investigation is to study the load-sharing ratio of RCFT columns subjected to axial compressive load by performing numerical simulations of RCFT columns with the nonlinear finite element analysis (FEA) program - ADINA. To achieve this goal, firstly proper material constitutive models for concrete, steel tube and reinforcement are proposed. Then axial compression tests of concrete, RC, CFT, and RCFT columns are carried out to verify proposed material constitutive models. Finally, by the plenty of numerical analysis with small-sized and big-sized columns, load-sharing ratio of RCFT columns was studied, the evaluation formulas and range were proposed, application of the formula was demonstrated, and following conclusions were drawn: The FEA model introduced in this paper can be applied to nonlinear analysis of RCFT columns with reliable results; the load-sharing ratio evaluation formula and range of CFT should not be applied to RCFT; The lower limit for the range of load-sharing ratio of RCFT can be smaller than that of CFT; the proposed formulas for load-sharing ratio of RCFT have practical mean in design of RCFT columns.

• 대한토목학회논문집
• /
• 제30권4A호
• /
• pp.383-389
• /
• 2010

현재 우리나라의 콘크리트구조설계기준은 강도설계법에 근간하고 있다. 강도설계법에 의해 휨부재를 설계할 경우, 콘크리트 응력-변형률 관계는 사용하중 상태에서 선형으로 가정하지만 이후 극한한계 상태까지에 대해서는 규정되어 있지 않다. 이로 인해 콘크리트구조설계기준에서는 처짐 및 균열폭 등의 산정에 대해 개별적인 규정을 두고 있다. 그러나 한계상태설계법에 근거한 EC에서는 재료에 대한 응력-변형률 관계를 규정하고 있다. 따라서 재료의 응력-변형률 관계로부터 휨강도 및 처짐 등을 직접 계산할 수 있다. 본 연구에서는 휨부재에 대하여 주어진 재료 모델을 바탕으로 평형방정식과 적합조건식을 적용하여 휨모멘트-곡률 관계를 계산하였다. 이로부터 휨강도 및 처짐을 산정하여 현행 콘크리트구조설계기준에 의한 값과 비교하였다. 해석 결과 재료 모델로부터 휨모멘트-곡률 관계를 통해 산정된 처짐은 실험 결과와도 비교적 잘 일치하고, 항복 이후의 처짐 계산도 가능한 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제40권8호
• /
• pp.751-757
• /
• 2016

본 논문은 스테어케이스법을 사용하여 크랭크 스로 부품용 S34MnV강의 피로한도의 신뢰도를 평가하는 것이다. 크랭크 스로 부품의 소재는 S34MnV이며, 뜨임 및 풀림 열처리된 단조강이다. 본 연구에서는 설계피로강도의 신뢰도를 예측하기 위해 축 하중 일정진폭 피로시험을 수행하였다. 시험편은 평균응력 0 MPa의 동일한 응력부하를 적용하였고, 즉 응력비는 -1로 하였다. 피로시험 결과는 Dixon-Mood 접근법으로 평가하였다. 스테어케이스법에 의해 예측된 피로강도의 평균과 표준편차는 각각 296.3 MPa 및 10.6 MPa로 나타났다. 마지막으로 어떤 임의의 파손 확률에 대한 피로강도의 신뢰도를 예측하였다. 본 연구에서 제안한 예측법은 단조강의 설계 최적화를 위한 피로강도 값을 결정할 수 있다.

• 대한기계학회논문집A
• /
• 제33권2호
• /
• pp.99-107
• /
• 2009

This study produced a design curve and fatigue limit for a variation in volume ratio and reduction ratio of TiNi/Al composites. In many cases, stress-life curve does not indicate fatigue limit, so it was presented by probabilistic-stress-life curve. Goodman diagram was used to analyze the fatigue strength of materials with a finite life determined by repeated load and the fatigue strength of endurance limit with an infinite life. The fatigue experiment was conducted using the scenk-type plane bending specimen in same shape. The result of the fatigue test, which had been conducted under consistent stress amplitude, was examined. (i) The optimal condition for TiNi/Al in accordance with hot pressing (ii) Impacts of fatigue limit caused by a variation in reduction ratio and volume ratio of TiNi/Al composites (iii) Probability distribution for fatigue limit of TiNi/Al2024 and TiNi/Al6061.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2017년도 특별논문집
• /
• pp.32-37
• /
• 2017

Due to the nature of semi-submergible drilling rig, various equipments are arranged in a limited space, and therefore the many types of outfitting holes passing through the hull structure are densely arranged and that is required the detailed structural strength evaluation in terms of ULS and FLS by class or client. Particularly, semi-submergible drilling rig has a variety of global load which affects the structure strength around holes compared to general commercial ship, and its response of stress is also complicated, so it is difficult to carry out the prediction design of structural strength evaluation and reinforcement. In this regard, this paper presents a case study on the evaluation of structural strength for the various holes and large openings of semi-submergible drilling rig conducted by our company, as well as an established hole verification procedure.

• Structural Engineering and Mechanics
• /
• 제51권5호
• /
• pp.847-866
• /
• 2014

This paper describes a formulation to predict optimum post-tensioning forces and cable dimensioning for self-anchored cable-stayed suspension bridges. The analysis is developed with respect to both dead and live load configurations, taking into account design constrains concerning serviceability and ultimate limit states. In particular, under dead loads, the analysis is developed with the purpose to calculate the post-tensioning cable forces to achieve minimum deflections for both girder and pylons. Moreover, under live loads, for each cable elements, the lowest required cross-section area is determined, which verifies prescriptions, under ultimate or serviceability limit states, on maximum allowable stresses and bridge deflections. The final configuration is obtained by means of an iterative procedure, which leads to a progressive definition of the stay, hanger and main cable characteristics, concerning both post-tensioning cable stresses and cross-sections. The design procedure is developed in the framework of a FE modeling, by using a refined formulation of the bridge components, taking into account of geometric nonlinearities involved in the bridge components. The results demonstrate that the proposed method can be easily utilized to predict the cable dimensioning also in the framework of long span bridge structures, in which typically more complexities are expected in view of the large number of variables involved in the design analysis.

• 한국전산구조공학회논문집
• /
• 제24권2호
• /
• pp.223-233
• /
• 2011

본 논문에서는 수직하중, 풍하중 및 지진하중에 의해 발생하는 변위 관련 구속조건을 만족하면서 RC(Reinforced Concrete) 빌딩 구조의 부피를 최소화하기 위한 설계문제를 정식화하였다. 구조해석 절차 자동화의 어려움으로 인해 실험 계획법과 근사화기법, 최적화기법을 이용한 근사모델기반 최적설계를 수행하였다. 특히, 만족할 만한 설계 결과를 얻을 때까지 설계변수의 범위와 구속조건의 허용값을 조정하는 단계적 최적설계 방법을 제안하였다. 제안된 단계적 최적설계 방법을 통해 주어진 구속조건을 모두 만족하면서 RC 빌딩 구조의 부피를 초기 설계 대비 53.3% 감소시키는 결과를 얻음으로 써 본 논문에서 보인 단계적 최적설계 방법의 타당성을 보였다.