• 한국군사과학기술학회지
• /
• 제20권1호
• /
• pp.55-62
• /
• 2017

For evaluating a large caliber ammunition tests, indoor ballistic test range is required to reduce the noise and fragments occurring during the test. To ensure the reliability of the indoor ballistics test range design, we carried out the analysis of the indoor test range using the AUTODYNE hydrodynamic code before its construction. The 120 mm tank ammunition is adopted as a reference model and we analysed the characteristics of the pressure distribution at fire area, the structure design at impact area, the over-pressure applied to the tunnel, and the sabot stopper design. The results of the analysis were applied to the design of the indoor ballistic test range.

• 한국군사과학기술학회지
• /
• 제24권1호
• /
• pp.70-78
• /
• 2021

Naval surface ships and submarines could be exposed to non-contact underwater explosion(UNDEX) environment. Equipment installed on the ships and submarines could be damaged by shock load generated by UNDEX environment. Therefore, shock survivability of equipment generally evaluated by shock tests. Ground based shock test machine such as Light weight shock test machine(LVSM) is developed to simulate shock load caused by UNDEX environment. In this study, linear dynamic model of LVSM is proposed and evaluated to improve shock test design procedure. Parameters of the model are decided by optimizing time domain response compared to zero payload experiment. Proposed model is verified by comparing simulation results and test results of maximum payload experiment. Finally, shock test design using the model is described for various test equipment weight.

• 한국컴퓨터정보학회논문지
• /
• 제23권11호
• /
• pp.67-74
• /
• 2018

The verification for the design limit margin of the power device for the information communication and surveillance systems using HALT(Highly Accelerated Life Test) reliability test is described. The HALT reliability test performs with a step stress method which change condition until the marginal step in a design and development phase. The HALT test methods are the low temperature(cold) step stress test, the high temperature(hot) step stress test, the thermal shock cyclic stess test, and the high temperature destruct limit(hot DL) step stress test. The power device is checked the operating performance during the test. In this paper, the HALT was performed to find out the design limit margin of the power device.

• 항공우주시스템공학회지
• /
• 제2권3호
• /
• pp.29-32
• /
• 2008

The overview of KUH design and development process is presented according to Buede's systems and development "vee" model. The system decomposition and integration activities exemplify KUH specification tree, design maturity and analysis according to design stage(conceptual, preliminary, and detail design), scheduled work breakdown structure, qualification test, ground test, and flight test. This process can be applied to the development of a new aircraft.

• 한국군사과학기술학회지
• /
• 제20권3호
• /
• pp.362-368
• /
• 2017

The endurance test is important to evaluate and predict defects of the vehicles. In particular, in order to improve the reliability of the endurance test for the powertrain system of military vehicles, the driving load is measured and analyzed at test courses and maneuvering roads. As a result, new test courses for powertrain system is additionally needed to improve test reliability. In this paper, it shows that new test courses for powertrain system is designed and constructed using the measuring and anlayzing result between CPG test courses and army maneuvering roads.

• 시스템엔지니어링학술지
• /
• 제7권2호
• /
• pp.7-11
• /
• 2011

A high-speed railway system represents a typical example of large-scale multi-disciplinary system, consisting of subsystems such as rolling-stock, electrical hardware, electronics, control, information, communication, civil technology etc. The system design and acquisition data of the large-scale system must be the subject under strict configuration control and management. Systems engineering technology development project for Korea next generation High-speed Electric Multiple Unit (HEMU) system in progress is a national large system development project that is not only a large-size and complex but also multi-disciplinary in nature. Therefore, all stakeholders must understand and share the functional and performance requirements of HEMU throughout its life-cycle phases. Also in the test and evaluation phase, all systems requirements must be verified. In 2011, the prototype train manufacturing will be completed. It will do test run on the commercial line and all systems requirements are verified until 2012. For the system verification, the test and evaluation process have to be established before the test trial run. Using a systems engineering tool, the system design database(SDD) with requirements traceability and development process management in the course of the development have to be established. This paper represents the test and evaluation process development based on the SEMP(Systems Engineering Management Plan) developed in the design stage. The test and evaluation process is refined and updated in comparison to the design stage one. The test and evaluation process consists of procedure, test and evaluation method and schedule. So through this process, it is defined that each systems requirements is verified on which test and about what time.

• 한국콘텐츠학회논문지
• /
• 제21권8호
• /
• pp.403-412
• /
• 2021

모바일 앱의 수가 기하급수적으로 늘어남에 따라 앱 개발과정에서 이루어지는 테스트의 자동화가 중요해지고 있다. 앱을 출시하기까지 다양한 유형의 테스트를 통해 반복적인 검증이 이루어지는데, 다양한 유형의 테스트 중 GUI 테스트를 중심으로 본 연구는 진행되었다. 안드로이드의 GUI 테스트 자동화 툴을 개발하기 위해서 안드로이드 앱 테스트의 UI Control 16가지와 Material Design Guideline에 대해서 기초 자료를 수집하였다. 그 후 기존 GUI 테스트 자동화 툴에 대해서 스크린 캡처 테스트 기반 2가지 툴과 소스코드 분석 테스트기반 4가지 툴 분석을 하였다. 분석을 통해 기존의 GUI 테스트 자동화 툴들은 시각적 설계, 인터페이스 사용 용이성, 컴포넌트 배치에 대해서는 고려하지 않고 있다는 점을 파악하였다. 이러한 기존 툴의 미비점을 보완하고자 새로운 GUI 테스트 자동화 툴 개발 방법으로 컴포넌트 선정이나 관리 분석 그리고 컴포넌트별 소스코드 예시로 탐색 메뉴나 버튼, 아이템 그룹화나 리스트에 관한 방법을 제시하였다. 본 연구는 GUI 테스트의 새로운 개발 방향을 제시함으로써 개발사의 안정적인 앱 배포에 기여할 수 있다는 점에서 의의가 있다.

• 한국정밀공학회지
• /
• 제18권1호
• /
• pp.147-153
• /
• 2001

This paper proposes a shaker system design for acceleration test of gimbal. Main reason of shaker system design is to give acceleration to the gimbal, which is moving and tracking the target on the tracking test equipment. The shaker system is mounted on the tracking test equipment. It uses the scotch yoke mechanism to have the constant movement in return. The Scotch yoke mechanism changes the rotational movement of constant velocity to simple harmonic motion.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2007년도 동계학술발표대회 논문집
• /
• pp.310-315
• /
• 2007

The FTL has been developed to be able to irradiate test fuels at the irradiation hole(IR1 hole) by considering its utility and user's irradiation requirements. FTL consists of In-Pile Test Section (IPS) and Out-of-Pile System (OPS). Test condition in IPS such as pressure, temperature and the water quality, can be controlled by OPS. For safety assurance IPS is designed to have dual stainless steel pressure vessel and OPS is composed of main cooling water system, emergency cooling water system, LMP(letdown, make-up, purification) system, etc. FTL Conceptual design was set up in 2001, basic design had completed including a design requirement, basic piping & instrument diagram (P&ID), and the detail design in 2004. In 2005, the development team carried out purchase and manufacture hardware and make a contract for construction work. FTL construction work began on August, 2006 and ended on March, 2007. After FTL development which is expected to be finished by 2008, FTL will be used for the irradiation test of the new PWR-type fuel and can maximize the usage of HANARO.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.22-25
• /
• 2004

This paper describes method and procedure for DDT (Design Development Test) of composite wind turbine blade composites. The test type of DDT is bending test, such as cantilever beam, based on the rated wind speed of wind power generation system. DDT was carried out in order to compare with the result of FEM analysis, characterize structural stability, verify manufacturing process and review test method of full scale blade.