• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.857-858
• /
• 2011

• Journal of Korea Water Resources Association
• /
• v.48 no.5
• /
• pp.367-377
• /
• 2015

ADCPs have been highlighted so far for measuring steramflow discharge in terms of their high-order of accuracy, relatively low cost and less field operators driven by their easy in-situ operation. While ADCPs become increasingly dominant in hydrometric area, their actual measurement accuracy for velocity and bathymetry measurement has not been sufficiently validated due to the lack of reliable bench-mark data, and subsequently there are still many uncertain aspects for using ADCPs in the field. This research aimed at analyzing inter-comparison results between ADCP measurements with respect to the detailed ADV measurement in a specified field environment. Overall, 184 ADV points were collected for densely designed grids for the given cross-section that has 6 m of width, 1 m of depth, and 0.7 m/s of averaged mean flow velocity. Concurrently, ADCP fixed-points measurements were conducted for each 0.2m and 0.02m of horizontal and vertical spacing respectively. The inter-comparison results indicated that ADCP matched ADV velocity very accurately for 0.4~0.8 of relative depth (y/h), but noticeable deviation occurred between them in near surface and bottom region. For evaluating the capacity of measuring bathymetry of ADCPs, bottom tracking bathymetry based on oblique beams showed better performance than vertical beam approach, and similar results were shown for fixed and moving-boat method as well. Error analysis for velocity and bathymetry measurements of ADCP can be potentially able to be utilized for the more detailed uncertainty analysis of the ADCP discharge measurement.

• The Journal of Korean Society for Radiation Therapy
• /
• v.8 no.1
• /
• pp.55-61
• /
• 1996

A radiation beam incident on irregular or sloping surface produces an inhomogeneity of absorbed dose. The use of a tissue compensator can partially correct this dose inhomogeneity. The tissue compensator should be made based on experimentally measured thickness ratio. The thickness ratio depends on beam energy, distance from the tissue compensator to the surface of patient, field size, treatment depth, tissue deficit and other factors. In this study, the thickness ratio was measured for various field size of $5cm{\times}5cm,\;10cm{\times}10cm,\;15cm{\times}15cm,\;20cm{\times}20cm$ for 4MV X-ray beams. The distance to the compensator from the X-ray target was fixed, 49cm, and measurement depth was 3, 5, 7, 9 cm. For each measurement depth, the tissue deficit was changed from 0 to(measurement depth-1)cm by 1cm increment. As a result, thickness ratio was decreased according to field size and tissue deficit was increased. Use of a representative thickness ratio for tissue compensator, there was $10\%$ difference of absorbed dose but use of a experimentally measured thickness ratio for tissue compensator, there was $2\%$ difference of absorbed dose. Therefore, it can be concluded that the tissue compensator made by experimentally measured thickness ratio can produce good distribution with acceptable inhomogeneity and such tissue compensator can be effectively applied to clinical radiotherapy.

• Journal of Korea Multimedia Society
• /
• v.17 no.7
• /
• pp.818-828
• /
• 2014

After emerging of Microsoft Kinect, the interest in three-dimensional (3D) depth image was significantly increased. Depth image data of an object can be converted to 3D coordinates by simple arithmetic calculation and then can be reconstructed as a 3D model on computer. However, because the surface coordinates can be acquired only from the front area facing Kinect, total solid which has a closed surface cannot be reconstructed. In this paper, 3D registration method for multiple Kinects was suggested, in which surface information from each Kinect was simultaneously collected and registered in real time to build 3D total solid. To unify relative coordinate system used by each Kinect, 3D perspective transform was adopted. Also, to detect control points which are necessary to generate transformation matrix, 3D randomized Hough transform was used. Once transform matrices were generated, real time 3D reconstruction of various objects was possible. To verify the usefulness of suggested method, human arms were 3D reconstructed and the volumes of them were measured by using four Kinects. This volume measuring system was developed to monitor the level of lymphedema of patients after cancer treatment and the measurement difference with medical CT was lower than 5%, expected CT reconstruction error.

• Journal of Periodontal and Implant Science
• /
• v.36 no.2
• /
• pp.427-434
• /
• 2006

The form of furcation influence both the pathogenesis of periodontal destruction and therapeutic results. The present study was performed to evaluate the effect of root trunk length on clinical outcomes of guided tissue regeneration. Total 30 mandibular first molars were evaluated in this study. Probing pocket depth, clinical attachment level, vertical defect depth and horizontal defect depth were measured at baseline and 6 month after GTR. Correlation coefficients between root trunk length and other clinical measurement were analyzed. The results of this study were as follows 1. The mean root trunk length in lower 1st molar was 2.15 mm. 2. Probing pocket depth, clinical attachment level, vertical defect depth and horizontal defect depth were significantly reduced at 6 month postoperatively compared to values of baseline 3. Correlation coefficient between root trunk length and vertical defect depth at baseline was 0.406 showing the positive correlation 4. Correlation coefficient between root trunk length and horizontal defect depth at baseline was -0.463 showing the negative correlation. 5. Correlation coefficient between root trunk length and decrease of horizontal defect depth after GTR was 0.654 showing the positive correlation. In conclusion, the root trunk length maybe effector for clinical outcome after guided tissue regeneration.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.5
• /
• pp.66-72
• /
• 1997

In this paper, we propose a method improving the accuracy of th eregistration coefficients calculated form two range images considering the measurement error. The employed range finder is based on triangulation and the depth measurement error is described with an error covariance matrix, which is based on thesensitivity of the range measurements. Experimental results demonstrate that the registration coefficients obtained with the proposed method are better than the results when the measurment errors are neglected.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.304-308
• /
• 2000

Surface roughness measurement system with capacitance type gap sensor. Tentative result from the calibration measurement showed the potential applicability of the sensor to the processed specimen. In order to test the sensitivity of the measurement system, several parameters including valley depth, width of the specimen have been changed. Effect of the charge area between sensor and specimen surface has been also analyzed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.7
• /
• pp.930-937
• /
• 2011

The characteristics of mean velocity and turbulence have been analyzed in the circular open channel flow using PIV measurement data for a wide range of water depth. The measured data are fitted to a velocity distribution function over the whole depth of the open channel. Reynolds shear stress and mean velocity in wall unit are compared with the analytic models for fully-developed turbulent boundary layer. Both the mean velocity and Reynolds shear stress have different distributions from the two-dimensional boundary layer flow when the water depth increases over 50% since the influence of the side wall penetrates more deeply into the free surface. The cross-stream Reynolds normal stress also has considerably different distribution in view of its peak value and decreasing rate in the outer region whether the water depth is higher than 50% or not.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.11 no.1
• /
• pp.38-43
• /
• 1991

The relationship between eddy current response and case hardening depth has been studied on SM40C(KS D-3752) and SCM440(KS D-3711) steels which were surface hardened by high frequency induction hardening. The results obtained in this study were as follows ; 1) Case hardening depth was successfully measured by observing the eddy current impedance changes of each steel. The impedance decreased linearly with increasing case hardening depth. 2) For large impedance gradient between the hardened surface and core metal, the eddy current response was more sensitive to case hardening depth than for low impedance gradient.

• The korean journal of orthodontics
• /
• v.6 no.1
• /
• pp.39-46
• /
• 1976

This study was undertaken to establish the cephalometric standards, using lateral cephalometric roentgenograms of 48 male and 53 female Korean adults with normal occlusion and acceptable profile. By Cohen's method, measurement of depth was taken parallel to the FH plane and expressed as a percentage of the cranial base depth (BA-N). And vertical height was measured along the line perpendicular to the FH plane and expressed as a percentage of the anterior face height (N-M). The following conclusions were obtained: 1) Means and standard deviations of craniofacial proportions of Korean adults were tabulated. 2) Cranial babe depth of male was greater than that of female. 3) The proportionate depth of the middle face was greater in female than in male. 4) The proportionate total anterior face height was greater in male than in female. And it was greater in Korean than in the white.