• The Journal of Advanced Prosthodontics
• /
• 제13권6호
• /
• pp.396-407
• /
• 2021

PURPOSE. Zirconia has exceptional biocompatibility and good mechanical properties in clinical situations. However, finite element analysis (FEA) studies on the biomechanical stability of two-piece zirconia implant systems are limited. Therefore, the aim of this study was to compare the biomechanical properties of the two-piece zirconia and titanium implants using FEA. MATERIALS AND METHODS. Two groups of finite element (FE) models, the zirconia (Zircon) and titanium (Titan) models, were generated for the exam. Oblique (175 N) and vertical (175 N) loads were applied to the FE model generated for FEA simulation, and the stress levels and distributions were investigated. RESULTS. In oblique loading, von Mises stress values were the highest in the abutment of the Zircon model. The von Mises stress values of the Titan model for the abutment screw and implant fixture were slightly higher than those of the Zircon model. Minimum principal stress in the cortical bone was higher in the Titan model than Zircon model under oblique and vertical loading. Under both vertical and oblique loads, stress concentrations in the implant components and bone occurred in the same area. Because the material itself has high stiffness and elastic modulus, the Zircon model exhibited a higher von Mises stress value in the abutments than the Titan model, but at a level lower than the fracture strength of the material. CONCLUSION. Owing to the good esthetics and stress controllability of the Zircon model, it can be considered for clinical use.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제25권4호
• /
• pp.295-303
• /
• 1999

Presented in this paper are the experimental results that measure rapid prototyping (RP) errors in 3D medical models. We identified various factors that can cause dimensional errors when producing RP models, specifically in maxillofacial areas. For the experiment, we used a human dry skull. A number of linear measurements based on landmarks were first obtained on the skull. This was followed by CT scanning, 3D model reconstruction, and RP model fabrication. The landmarks were measured again on both the reconstructed models and the physical RP models, and these were compared with those on dry skull. We focused on major sources of errors, such as CT scanning, conversion from CT data to STL models, and RP model fabrication. The results show that the overall error from skull to RP is $0.64{\times}0.36mm(0.71{\times}0.66%)$ in absolute value. This indicates that the RP technology can be acceptable in the real clinical applications. A clinical case that has applied RP models successfully for treatment planning and surgical rehearsal is presented. Although the use of RP models is rare in the medical area yet, we believe RP is promising in that it has a great potential in developing new tools which can aid diagnosis, treatment planning, surgical rehearsal, education, and so on.

• 대한치과기공학회지
• /
• 제34권4호
• /
• pp.353-359
• /
• 2012

Purpose: The aim of this study measured and compared the marginal and internal fit of metal cores with two base metal alloy (Ni-Cr alloy(non-beryllium), Co-Cr alloy). Methods: Maxillary right first molar abutment fabricated by titanium was prepared for this study. Impressions(10ea) were made from titanium model, and study models were poured with improved dental stone. Wax cores of twenty were prepared for burn-out and casting. Ten wax cores cast Ni-Cr alloy(non-Be), and finally ten cast Co-Cr alloy. Marginal and internal fit of cores was evaluated using silicone replica technique and digital microscope(x160). The data were statistically analyzed with the independent samples t-test (${\alpha}$ <.05). Results: Mean(standard deviation, SD) marginal and internal fit total size of Ni-Cr alloy(non-Be) group was $73.3(14.4){\mu}m$ and of Co-Cr alloy group $65.6(17.4){\mu}m$. The marginal and internal fit total size of Ni-Cr alloy group(non-Be) was statistically significantly greater than that of Co-Cr alloy group (P=.004). Conclusion: Co-Cr alloy cores in this study had a better marginal fit than Ni-Cr alloy(non-Be) cores.

• Journal of Korean Dental Science
• /
• 제7권2호
• /
• pp.66-79
• /
• 2014

Purpose: To analyze the amount and pattern of tooth movement and the changes in arch dimension of mandibular dentition after orthodontic treatment using a new three-dimensional (3D)-indirect superimposition method. Materials and Methods: The samples consisted of fifteen adult patients with class I bialveolar protrusion and minimal anterior crowding, treated by extraction of four first premolars with conventional sliding mechanics. After superimposition of 3D-virtual maxillary models before and after treatment using best-fit method, 3D-virtual mandibular model at each stage was placed into a common coordinate of superimposition using 3D-bite information, which resulted in 3D-indirect superimposition for mandibular dentition. The changes in mandibular dental and arch dimensional variables were measured with Rapidform 2006 (INUS Technology). Paired t-test was used for statistical analysis. Result: The anterior teeth moved backward, displaced laterally, and inclined lingually. The posterior teeth showed statistically significant contraction toward midsagittal plane. The amounts of backward movement of anterior teeth and forward movement of posterior teeth showed a ratio of 6 : 1. Although the inter-canine width increased slightly (0.8 mm, P<0.05), the inter-second premolar, inter-first molar, and inter-second molar widths decreased significantly with similar amounts (2.2 mm, P<0.05; 2.3 mm, P<0.01; 2.3 mm, P<0.001). The molar depth decreased (6.7 mm, P<0.001) but canine depth did not change. Conclusion: A new 3D-indirect superimposition of the mandibular dentitions using best-fit method and 3D-bite information can present a guideline for virtual treatment planning in terms of tooth position and arch dimension.

• 대한치과기공학회지
• /
• 제42권3호
• /
• pp.220-227
• /
• 2020

Purpose: This study aims to investigate the cusp variation pattern of the Korean mandibular second premolar and to determine the difference in tooth diameter and surface area using a virtual three-dimensional model. Methods: Dental casts from 69 students were scanned as a virtual dental models with a three-dimensional dental model scanner. Tooth diameter, absolute and relative individual areas, total crown area, the number of lingual cusps and central groove pattern were analyzed using RapidForm 2004. The Mann-Whitney U-test and the Kruskal-Wallis test were performed to verify sexual dimorphism, the difference in tooth diameter and surface according to the cusp variation pattern (α=0.05). Results: There was no significant difference except in buccolingual diameter (p<0.05) and buccolingual diameter at the cervix (p<0.05). The relative surface area of the total clinical crown was 65.76% for the buccal half and 34.24% for the lingual half, with a ratio of 2:1. In the case of the presence of two lingual cusps, the ratio was 21.47% for the mesiolingual half and 14.12% for the distaolingual half, with a ratio of 3:2. The dominant central groove patterns of the second premolar were the H-pattern (42.0%), followed by the Y-pattern (37.7%), then the U-pattern (20.3%). The relative buccal half was largest in the U-pattern central groove and the relative lingual half was largest in the Y-pattern central groove (p<0.05). Conclusion: This study is significant in that it measured quantitative surface areas and the findings could be a meaningful reference to comprehend dental anatomy in Koreans.

• 대한치과교정학회지
• /
• 제50권3호
• /
• pp.216-226
• /
• 2020

Root resorption can be caused by several factors, including contact with the cortical bone. Here we report a case involving a 21-year-old female with Angle Class II, division 1 malocclusion who exhibited significant root resorption in the maxillary right central incisor after orthodontic treatment. The patient presented with significant left-sided deviation of the maxillary incisors due to lingual dislocation of the left lateral incisor and a Class II molar relationship. Cephalometric analysis demonstrated a Class I skeletal relationship (A point-nasion-B point, 2.5°) and proclined maxillary anterior teeth (upper incisor to sella-nasion plane angle, 113.4°). The primary treatment objectives were the achievement of stable occlusion with midline agreement between the maxillary and mandibular dentitions and appropriate maxillary anterior tooth axes and molar relationship. A panoramic radiograph obtained after active treatment showed significant root resorption in the maxillary right central incisor; therefore, we performed cone-beam computed tomography, which confirmed root resorption along the cortical bone around the incisive canal. The findings from this case, where different degrees of root resorption were observed despite comparable degrees of orthodontic movement in the bilateral maxillary central incisors, suggest that the incisive canal could be an inducing factor for root resorption. However, further investigation is necessary to confirm this assumption.

• The Journal of Advanced Prosthodontics
• /
• 제5권2호
• /
• pp.179-186
• /
• 2013

PURPOSE. One of the most important factors in evaluating the quality of fixed dental prostheses (FDPs) is their gap. The purpose of this study was to compare the marginal and internal gap of two different metal-ceramic crowns, casting and selective laser sintering (SLS), before and after porcelain firing. Furthermore, this study evaluated whether metal-ceramic crowns made using the SLS have the same clinical acceptability as crowns made by the traditional casting. MATERIALS AND METHODS. The 10 study models were produced using stone. The 20 specimens were produced using the casting and the SLS methods; 10 samples were made in each group. After the core gap measurements, 10 metal-ceramic crowns in each group were finished using the conventional technique of firing porcelain. The gap of the metal-ceramic crowns was measured. The marginal and internal gaps were measured by two-dimensional and three-dimensional replica techniques, respectively. The Wilcoxon signed-rank test, the Wilcoxon rank-sum test and nonparametric ANCOVA were used for statistical analysis (${\alpha}$=.05). RESULTS. In both groups, the gap increased after completion of the metal-ceramic crown compared to the core. In all measured areas, the gap of the metal cores and metal-ceramic crowns produced by the SLS was greater than that of the metal cores and metal-ceramic crowns produced using the casting. Statistically significant differences were found between cast and SLS (metal cores and metal-ceramic crown). CONCLUSION. Although the gap of the FDPs produced by the SLS was greater than that of the FDPs produced by the conventional casting in all measured areas, none exceeded the clinically acceptable range.

• 한국콘텐츠학회논문지
• /
• 제18권12호
• /
• pp.218-228
• /
• 2018

본 연구의 목적은 치의학 임상실습 장면에서 활용이 가능한 가상현실 기반의 치아발치 교육콘텐츠를 개발하는 것이다. 이러한 목적을 달성하기 위해 '학습내용 분석-설계모형 도출-개발-타당도 검증-수정 및 콘텐츠 완성'의 단계를 거쳐 치아발치 실습용 교육콘텐츠를 개발하였다. 연구결과, 3D모델링을 적용하여 환자의 안면해부학적 모델을 구축하고, 치아발치 수술과정 시나리오를 바탕으로 가상현실 기술을 적용한 단계별 수술장면을 에니메이션으로 구축하였다. 개발된 콘텐츠에 대한 전문가 평가를 실시하였으며, 인터페이스 타당도(M: 4.81, SD: 0.72)와 내용타당도(M:4.66, SD: 0.71)를 검증한 결과 타당하게 설계된 것으로 분석되었다. 따라서 개발된 치아발치 실습용 교육콘텐츠는 치의학 전공생의 임상수행 능력을 향상시키는데 적절한 도구로 판단된다. 본 연구를 토대로 의료 분야의 다양한 실습장면을 지원할 수 있는 가상현실 기술 기반의 교육용 콘텐츠 개발 연구가 활성화되기를 기대한다.

• 대한치과교정학회지
• /
• 제52권6호
• /
• pp.387-398
• /
• 2022

Objective: Controlling the incisal inclination is fundamental in orthodontics. However, the relationship between the inclination prescription and its clinical outcome is not obvious, and the incisal inclination changes generated by different bracket prescriptions were investigated. Methods: Twenty-eight non-extraction dental Class II patients (15 females, 13 males; mean age = 12.9) were retrospectively analyzed. Patients were treated using passive self-ligating fixed appliances with three inclination prescriptions for maxillary incisors (high, standard, low), and two for mandibular incisors (standard, low). Clinical outcomes were compared among different prescriptions, and regression analysis was used to explain the effects of bracket prescriptions and to understand the prescription selection criteria (α = 0.05). Results: For maxillary central incisors, low and high prescriptions were related to linguoversion (p = 0.046) and labioversion (p = 0.005), respectively, while standard prescription maintained the initial dental inclination. Maxillary lateral incisors did not show significant changes. For mandibular incisors, low prescription led to linguoversion (p = 0.005 for central incisors, p = 0.010 for lateral incisors), while standard prescription led to labioversion (p = 0.045 for central incisors, p = 0.005 for lateral incisors). The factors affecting inclination changes were the imposed change and selected prescription, while prescription selection was influenced by the initial dental inclination and initial intercanine distance. Conclusions: The direction of correction of incisal inclination can be controlled by choosing a certain prescription, but the final inclination may show limited consistency with it. The amount of imposed inclination change was the most relevant predictor of the clinical outcome.

• Journal of Oral Medicine and Pain
• /
• 제47권4호
• /
• pp.198-205
• /
• 2022

Purpose: The first-line treatment of temporomandibular joint disorders (TMDs) should include self-management and education. Self-management techniques include moist heat application, stretching, diet control, and mandibular rest position adjustment. Although the effectiveness of video educational resources has been studied in multiple sectors, their application in TMD management has not yet been explored. This study seeks to assess how effective media education was at motivating TMD patients to self-management and improve symptoms. Methods: Data were obtained from the hospital records of TMD patients who visited the Department of Oral Medicine, Yonsei University Dental Hospital, between May 2020 and December 2021. First, without any differences between groups, a significance analysis was conducted between the degree of self-management and symptom improvement over time. At the second visit, one group received media education (n=31) linked to TMD management, while the other received written-oriented education (n=45). At the third visit, the number of precautions taken by the patients was determined and contrasted to that recorded in the previous visit between the groups. Generalized estimated equation multivariate models were applied for statistical analysis. Results: In the media education group, the frequency of stretching and the number of patients on pain-free diets increased substantially. Taking precautions improved daily pain intensity, maximum mouth opening, and pain intensity during the maximum unassisted opening. Conclusions: Media education could be beneficial for TMD patients because it allows them to take self-management precautions. The symptoms of the media education group improved, with no considerable distinction between both groups.