• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.3
• /
• pp.225-235
• /
• 2010

There are many types of the geometric transitions such as dent, bulge, protrusion, expansion, etc, on the inner and outer surfaces of heat exchanger tubes, steam generator tubes, and condenser tubes of nuclear power plants. Such geometric transition causes a local residual stress in heat exchanger tubes and acts as a structural factor accelerating the evolution of defects, in particular stress corrosion cracks. In the conventional eddy current test methods, the bobbin coil profilometry can provide 2-dimensional geometric information on the variation of the average inner diameter along the tube length, but the 3-dimensional distribution and the quantitative size of a local geometric transition existing in the tube cannot be measured. In this paper, a new eddy current probe, developed for the 3-dimensional profile measurement, is introduced and its superior performance is compared with that from the conventional bobbin coil profilometry for the various types of geometric transition. Also, the accuracy of the probe for the quantitative profile measurement is verified by comparing the results with that from the laser profilometry. It is expected that the new eddy current probe and techniques can be effectively used for an optimization of the tube expansion process, and the management of tubes with geometric transitions in service.

• Corrosion Science and Technology
• /
• v.23 no.3
• /
• pp.215-220
• /
• 2024

Recently, the demand for Zn-Ni electrogalvanized steel sheets for home appliances and automobiles is increasing. Products should have a thick plating (30 to 40 g/m²) on both side with a thin thickness (≤ 0.8 mm) and the highest surface quality. By a high current density operation, current is concentrated in the edge part of the steel sheet, resulting in large surface dent defects due to dendritic plating. This can lead to a low productivity due to low line speed operation. To solve this problem, this study aimed to identify factors influencing dendritic plating. A cylindrical electroplating device was manufactured. Effects of cut edge shape and thickness of steel plate, current density, temperature, flow rate, electrolyte concentration, and pH on dendrite generation of Zn-Ni electroplating were examined. To investigate effect of edge shape of the steel sheet, the steel sheet was manufactured using three processing methods: shearing, polishing after shearing, and laser. Relative effects thickness and cut edge processing methods of the steel plate, current density, temperature, flow rate, electrolyte concentration, and pH of plating solution on dendrite plating were investigated. To prevent dendrite plating, an edge mask was manufactured and its application effect was investigated.

• Journal of Animal Science and Technology
• /
• v.44 no.2
• /
• pp.251-260
• /
• 2002

The corn (Zea mays L) planting date in a double-cropping system is delayed until mid-May due to delayed rye harvest on May. This experiment was conducted to determine the optimum harvesting time for high yield and the best quality of silage corn at late planting date after harvesting winter rye. Corns were planted on 21 May and harvested at eight different maturity stage at Seoul National University Experimental Livestock Farm, Suwon in 1997. Maturities were B (blister; 16 days after silking), M (milk; 20 days), LM (late milk; 24 days), SD (soft dough; 28 days), ED (early dent; 33 days), FD (full dent; 38 days), LD (late dent; 44 days) and PM (physiological maturity; 53 days) stages. The percentage of whole plant dry matter (DM) showed optimum range for silage making (29.0 to 38.5%) when corn plant was harvested at between ED and LD stages. Maximum whole plant DM (14,831 kg/ha) and total digestible nutrients (TDN) yields (10,675 kg/ha) reached at full dent stage. The percentage of whole plant acid detergent fiber (ADF) was decreased from 35.4 to 22.1%, and that of neutral detergent fiber (NDF) was also decreased from 63.8 to 46.0% as harvest stage progressed. These changes in chemical compositions were associated with changes in plant part composition. A progressive increase in total ear, and the decrease in stover portion in the plant were observed with advance in harvest stage. Calculated on net energy for lactation (NEL) and TDN values based on ADF percentage of stover plant decreased by ED stage and then increased by PM stage. But NEL and TDN values of ear and whole plant increased as harvest stage progressed. While in vitro dry matter digestibility of stover was decreased from 61.1 to 49.7%, whole plant was increased from 58.3 to 65.7% as maturity advanced (P$<$0.05). The results of this study indicate that corn can be harvested for silage at full (1/2 milkline) and late dent (2/3 milkline) stages for maximum yield and optimum quality at late planting. And days after silking at late planting was 38 and 44 days.

• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.2
• /
• pp.29-51
• /
• 1990

This study was designed to compre the tensile bond strength of 4-META containging denture base resin to Co-Cr alloys after various surface treatments. Especially the surface treatment of sandblasting the mental with aluminum oxide and treating in oxidizing solution composed of 3% aqueous sulfuric acid with 1% potassium manganate were compared. Effect of surface roughness on bonding was measured after sandblasting with 50um, 300um aluminun oxide and polishing with emery pater. Also the effects of wax and wax solvent on bonding were observed. According to the type of polymerization process, heat-cured Meta-Dent resin and autopolymerizing Meta-Fast resin were used. For some specimnens, the tensile bond strength were measured agter three pre-conditions : 1day after bonding, immersed in water at $75^{\circ}C{\pm}3^{\circ}C$ for 4weeks, under normal ambient condition for 4weeks. The following results were obtained from this study : 1. The bond strengths of resins containing 4-META were significantly higher than those of conventional denture base resins(p<0.05). 2. Autopolymerizing Meta-Fast resin had higher bond strength than heat-cured Meta-Dent, resin(p<0.05). 3. The bond strengths of Biosil and Nobilium to 4-META containging resins were not significally different(p>0.05). 4. Stable adhesion can be achieved when mechanically roughen the metal surface by snadblasting with $50{\mu}m$ aluminum oxide than treating in an oxidizing soluing with potassium manganate(p<0.05). 5. Once the metal surface is contaminated with wax, the bond srtength decreased greatly in spite of wax wash with boiling water. But the bond strength recovered significantly with the use of wax solvent 6. Meta-Dent resin had higher bond strength when roughen the metal surface with $50{\mu}m$ aluminum oxide than with $300{\mu}m$ aluminum oxide(p<0.05). In case of Meta-Fast, resin, the use of $300{\mu}m$aluminum oxide was a little advantageous of bonding, but was statistically insignificant(p>0.05).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.2
• /
• pp.184-190
• /
• 2008

Various ECT techniques have been applied basically to assess the integrity of steam generator tithing in nuclear power plant. Among these techniques, the bobbin probe technique is applied generally to examine the volumetric flaws such as a crack-like defect and wear which is generally occurred on steam generator tubing, and additionally MRPC probe is used to examine closely tile top of tubesheet and bending regions due to the high possibility of cracking. Dent and bulge also may be formed on tube during installation process and operation of steam generator, but the dent and bulge indications greater than specific size criteria are recorded on examination report because these indications are not considered as flaw. These indications can be easily detected with bobbin probe and approximately sized with profile bobbin probe, but the size and shape can not be accurately verified. Accordingly, in this study, the $8{\times}1$ multi-array EC probe was designed to increase the measurement accuracy of the sectional profiling EC testing of tube. As a result, we would like to propose the application of $8{\times}1$ multi-array EC probe for the measurement of size and shape of profile change on steam generator tube in OPR-1000 nuclear power plant.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.6
• /
• pp.612-618
• /
• 2019

In the unmanned vehicle industry, the market is exploding due to the rapid development of public and private demands along with the technological development of the 4th Industrial Revolution. In addition, unmanned mobiles are being used for communication services. In this paper, we analyzed the communication performance of unmanned aerial vehicle according to the characteristics of Doppler frequency. The Doppler frequency was calculated using the geometric model of the unmanned aerial vehicle, and the Doppler frequency of 10km, 30km, 300km, 1000km per hour and the BER performance by AWGN were measured by considering the unmanned high speed unmanned vehicle based on the position of the controller. The Doppler frequency model uses a Dent model and adds additive white Gaussian noise (AWGN) to check the bit errors of the transmitter and receiver. Low speed unmanned vehicles generally exhibited a BER performance of 0.2, while high speed unmanned vehicles generally exhibited a BER performance of 0.06. As the frequency band increases at the same speed, the BER performance increases, and when the speed increases in the same frequency band, the BER performance decreases. This is confirmed by the simulation results to predict theoretically predictable BER performance. In the frequency bands of 2.6 GHz, 5 GHz, and 28 GHz, the BER characteristics by Doppler frequency and the BER characteristics by controller function are verified. effect was confirmed.

• Proceedings of the KACD Conference
• /
• 2001.11a
• /
• pp.577-577
• /
• 2001

The lastest concepts in bonding are "total etch", in which both enamel and dentin are etched with an acid to remove the smear layers, and "wet dentin" in which the dentin is not blown dry but left moist before application of the bonding primer. Ideally, the application of a bonding agent to tooth structure should be insensitive to minor contamination from oral fluids. Clinically contaminations such as saliva, gingival fluid, blood and handpiece lubricant are often encountered by dentists during preparation of a restoration. The aim of this study was to evaluate the effect of contamination by hem-ostatic agents on shear bond strength of compomer restorations. One hundred and ten extracted human maxillary and mandibular molar teeth were collected. The teeth were cleaned from soft tissue remnant and debris and stored in physiologic solution until they were used. Small flat area on dentin of the buccal surface were wet ground serially with 400, 800 and 1200 abrasive paper on automatic polishing machine. The teeth were randomly divided into 11 groups. Each group was conditioned as follows: Group 1 : Dentin surface was not etched and not contaminated by hemostatic agents. Group2 : Dentin surface was not etched but was contaminated by Astringedent (Ultradent product Inc., Utah, U.S.A.). Group3 : Dentin surface was not etched but was contaminated by Bosmin (Jeil Phann, Korea.). Group4 : Dentin surface was not etched but was contaminated by Epri-dent (Epr Industries, NJ, U.S.A.). Group5: Dentin surface was etched and not contaminated by hemostatic agents. Group 6 : Dentin surface was etched and contaminated by Astringedent. Group7 : Dentin surface was etched and contaminated by Bosmin. Group8 : Dentin surface was etched and contaminated by Epri-dent. Group9 : Dentin surface was contaminated by Astringedent. The contaminated surface was rinsed by water and dried by compressed air. Group10 : Dentin surface was contaminated by Bosmin. The contaminated surface was rinsed by water aud dried by compresfed air. Group 11 : Dentin surface was contaminated by Epri-dent. The contaminated surface was rinsed by water and dried by compresfed air. After surface conditioning, F2000 was applicated on the conditoned dentin surface. The teeth were thermocycled in distilled water at $5^{\circ}C\;and\;55^{\circ}C$ for 1000 cycles. The samples were placed on the binder with the bonded compomer-dentin interface parallel to the lmife-edge shearing rod of the Universal testing machine(Zwick 020, Germany) running at a cross head speed of 1.0mmimin. There were no significant differences in shear bond strength between groups 1 and group 3 and 4, but group 2 showed significant decrease in shear bond strength compared with group 1. There were no significant differences in shear bond strength between group 5 and group 7 and 8, but group 6 showed significant decrease in shear bond strength compared with group 5. There were no significant differences in shear bond strength between group 5 and group 9, 10 and 11.

• The Korean Journal of Food And Nutrition
• /
• v.33 no.5
• /
• pp.588-597
• /
• 2020

This study was conducted to secure basic information for corn processing by comparing the quality characteristics according to maize cultivars and kernel types (dent, intermediate, flint-like). As a result of analyzing 15 cultivars, a range of measurements were observed: 100-kernel weight, 22.89~35.63 g; moisture, 7.57~8.42%; crude protein, 8.46~11.45%; crude lipids, 3.26~4.83%; Hunter's L-value, 83.70~86.79; a-value, 2.61~5.49; b-value, 22.01~28.15; and total carotenoids, 6.74~17.07 ㎍/g. Significance among the cultivars was shown in all quality characteristics (p<0.001), but the significance among the kernel types was found only in crude protein (p<0.005), crude fat (p<0.001), and Hunter's L-value (p<0.05). The hardness of maize was decreased proportionally to the soaking time for all maize cultivars (p<0.001). In particular, with the same soaking time for different kernel types, the hardness difference was shown in the order of flint-like > dent ≒ intermediate. It was confirmed that the decrease in the hardness of flint-like kernel of close to that of hard-type starch was slowed compare dent and intermediate kernels. So it is expected the some characteristic of kernel types will contribute to the appropriate customized use of the developed cultivars.

• The Journal of Advanced Prosthodontics
• /
• v.16 no.2
• /
• pp.126-138
• /
• 2024

PURPOSE. The aim of this study was to evaluate the influence of different 3D dental resins, using a manufacturer recommended printer and a third-party printer, on cellular responses of human gingival cells. MATERIALS AND METHODS. Three NextDent resins (Denture 3D+, C&B MFH and Crowntec) were used to produce specimens on printers NextDent 5100 (groups ND, NC and NT, respectively) and Phrozen Sonic Mini 4K (groups PD, PC and PT, respectively). Human gingival fibroblasts were cultured and biocompatibility was evaluated on days 1, 3 and 7. IL-6 and IL-8 concentrations were evaluated at 3 days using ELISA. Surface roughness was evaluated by a contact profilometer. SEM and fluorescence micrographs were analyzed at days 1 and 7. Statistical analyses were performed using SPSS and mean differences were tested using ANOVA and post-hoc Tukey tests (P < .05). RESULTS. There was an increase in cellular viability after 7 days in groups PC and PT, when compared to group PD. ND group resulted in higher concentration of IL-6 when compared to PT group. SEM and fluorescence micrographs showed less adhesion and thinner morphology of fibroblasts from group PD. No significant differences were found regarding surface roughness. CONCLUSION. The use of different printers or resins did not seem to influence surface roughness. NextDent 5100 and Phrozen Sonic Mini 4K produced resins with similar cellular responses in human gingival fibroblasts. However, Denture 3D+ resin resulted in significantly lower biocompatibility, when compared to C&B MFH and Crowntec resins. Further testing is required to support its long-term use, required for complete dentures.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.577-577
• /
• 1989

In this paper, a detail evaluation of ultimate strength of offshore unstiffened tubular members with bending and local denting damage which are subjected to combined axial force and bending moment and to component load is presented through theoretical and experimental approaches. Based upon the results obtained here, the damage effect on the ultimate strength of tubular member under combined loads and component load is investigated.