• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국의학물리학회지:의학물리
• /
• 제20권2호
• /
• pp.72-79
• /
• 2009

I-131은 갑상선에 주로 집적되어 갑상선의 기능을 평가하는데 활용됨은 물론 높은 에너지의 베타선을 방출함으로써 암의 치료에도 널리 사용되고 있는 방사선 핵종이다. 그러나 I-131은 다양한 에너지의 감마선을 방출함으로써 핵의학 영상의 정량화가 어렵다. 특히 고에너지 영역의 감마선에 의한 격벽투과(septal penetration)와 산란선은 핵의학 진단영상에 악 영향을 미치게 된다. 본 연구에서는 격벽투과가 영상에 미치는 영향과 I-131의 산란보정 방법을 몬테카를로 시뮬레이션을 활용하여 알아보고자 하였다. 본 실험을 위하여 임상에서 사용되고 있는 범용성 고에너지 조준기를 장착한 핵의학 영상 기기인 FORTE 시스템(Philips, Netherlands)에 대해 모사하였다. 격벽투과가 영상에 미치는 영향을 알아보기 위하여 고에너지 조준기의 격벽을 두 가지 종류로 모사하여 보았다. 한 종류는 실제로 사용하고 있는 납으로 격벽을 모사하였으며, 다른 한 종류는 높은 에너지의 감마선이 투과할 수 없는 밀도와 원자번호가 아주 높은 임의의 물질로 구성하여 모사하였다. 각 각의 조준기를 통해 물팬텀안의 I-131 선 선원의 영상을 획득한 결과 납 격벽에서 획득한 선 선원의 반치폭 (Full Width at Half with Maximum, FWHM)과 십치폭(Full width at Tenth with Maximum, FWTM)은 각 각 41.2 mm, 206.5 mm였으며, 높은 에너지의 감마선이 투과할 수 없는 임의의 물질로 만든 격벽의 조준기에서는 반치폭과 십치폭이 각 각 27.3 mm, 47.6 mm로 측정되었다. 이는 고에너지의 감마선에 의한 격벽투과가 핵의학 영상의 선예도를 나쁘게 한다는 것을 알 수 있다. 또한 I-131을 이용한 핵의학 영상의 산란보정을 위하여 물 팬텀 속의 점 선원을 모사하고 영상을 획득하였다. 산란보정 방법으로는 삼중광봉우리창(Triple Energy Window method, TEW)을 이용하여 획득 영상 내의 산란선을 유추하는 방법을 사용하였다. 그러나 이러한 방법은 중심에너지 창의 범위에 따라 유추된 산란선의 양에 영향이 있으므로 더 정확한 산란선 유추를 위해 확장된 삼중광봉우리창(Extended Triple energy Window method, ETEW)을 적용, 기존의 방법과 비교하였다. 실험 결과 시뮬레이션의 데이터 분류를 통한 산란선으로만 획득된 점 선원 영상과 TEW와 ETEW 방법을 통해 유추된 산란선 영상결과, ETEW 방법으로 산란선을 유추한 방법이 기존의 TEW 방법보다 더 정확함을 알 수가 있었다. 본 연구는 시뮬레이션을 통한 I-131의 특성을 평가함으로써 I-131을 이용한 동위원소 치료 및 GATE 프로그램 연구의 기초자료로 활용될 수 있을 것으로 기대된다.

• 한국환경생태학회지
• /
• 제34권1호
• /
• pp.9-17
• /
• 2020

섬에 유입된 고양이(Felis catus)는 외래 포식자로서 섬 고유종의 멸종이나 절멸, 생물 다양성 감소 등의 직접적인 요인으로 작용할 수 있다. 본 연구는 제주도의 부속섬인 마라도(N 33° 07', E 126° 16')에 유입되어 서식하는 고양이의 개체군 현황과 행동권, 서식지 이용특성을 파악하기 위해 실시되었다. 2018년 3월부터 2018년 7월까지 직접관찰과 포획-재포획법을 통해 개체수 추정 결과, 번식 가능한 성체 총 20마리를 확인하였다. 이 중 10마리에 GPS 무선추적장치를 부착하여 추적한 결과 고양이의 행동권 크기는 12.05±6.99 ha (95% KDE: kernel density estimation), 핵심서식지 크기는 1.60±0.77 ha (50% KDE)로 나타났다. 성별에 따른 행동권과 핵심서식지의 크기는 통계적으로 유의하지 않았고, 10마리 중 8마리가 먹이획득이 쉬운 인간 거주지역을 핵심서식지로 이용하였다. 또한 마라도에 번식하는 멸종위기종인 뿔쇠오리(Synthliboramphus wumizusume)의 번식지에 5마리, 섬개개비(Locustella pleskei)의 번식지에 6마리가 접근하는 것을 각각 확인하였다. 본 연구는 마라도의 고양이 개체수와 행동권에 대한 정보를 최초로 파악하였으며, 특히 고양이 행동권 분석을 통해 철새와 멸종위기종에 대한 가해 가능성을 제시하였다. 철새와 멸종위기 조류의 서식지인 마라도에서 발생할 수 있는 고양이의 피해를 줄이기 위해 향후 고양이의 포식압, 고양이와 멸종위기 조류 개체군의 변동에 대한 모니터링에 관한 연구와 함께, 필요시 고양이 개체군 관리방안을 마련할 필요가 있을 것으로 판단된다.

• 한국농림기상학회지
• /
• 제18권1호
• /
• pp.1-15
• /
• 2016

광릉숲, 태화산 서울대 학술림, 가리왕산의 낙엽활엽수림에서 연간 낙엽 낙지 생산량과 가을철 낙엽에 의한 수종별 엽면적지수를 산출하고, 간접적인 방법의 것과 비교하였다. 연간 낙엽 낙지 생산량은 천이 단계 증가에 따른 임분의 바이오매스 축적량이나 수종구성 등에 따라 그 양과 비율이 다르게 나타났으며(Table 2), 특히 수종마다 낙엽의 양에 차이는 있지만 모든 임분에서 여름철 이후에 집중되는 경향을 보여(Fig. 1), 가을철의 한시적인 낙엽 수집만으로도 최대 엽면적지수의 추정은 유효한 것으로 나타났다. 더욱이, 이러한 낙엽의 수집으로 낙엽의 양 뿐만 아니라 수종마다 SLA와 탈락시기를 정확하게 추정할 수 있었고(Table 3), 간접방법으로는 불가능하기 때문에 국내에서는 시도되지 않았던 각 수종별 엽면적지수를 국내 최초로 산출 할 수 있었다(Fig. 2). 본 연구를 통하여 수종별 낙엽량과 엽면적지수는 각 수종의 흉고단면적과 유의한 상관관계를 보였으나, 간접방법에 의한 전체 엽면적지수를 흉고단면적의 비율을 곱하여 수종별 엽면적지수로 추정하는 것은 상당한 오차가 발생할 수 있음을 알 수 있었다(Fig. 3). 또한 간접방법에 의한 엽면적지수는 잎의 양이 늘고 밀집도가 높아질수록 과소평가되는 오류가 발생하기 쉽기 때문에(Fig. 4, 5), 직접방법에 의한 엽면적지수와의 평가는 필수적임을 확인할 수 있었다. 따라서, 낙엽에 의한 직접적인 엽면적지수의 측정을 시도함으로써 다양한 수종이 공존하는 우리나라 온대 활엽수림에서 임분의 수종 구성과 밀도, 천이단계, 입지환경 등에 따른 낙엽량과 수종별 엽면적지수의 변화 양상을 정량적으로 확인 할 수 있었다.

• 한국지리정보학회지
• /
• 제20권2호
• /
• pp.32-46
• /
• 2017

최근 급격한 도시팽창 및 각종 산업시설의 밀집화는 도심지역의 지형지물 변화에 많은 영향을 줌으로써 한 지역에 다양한 높이의 건축물 또는 평지와 산지가 함께 존재하는 현상을 초래하였다. 본 연구에서는 내풍설계 시 중요한 인자인 풍속고도분포계수를 산정하기위해 건축물의 높이별로 공간정보 기반 밀집도 분석을 활용하여 지표면조도를 구분하고자 한다. 공간데이터의 확보를 위해 수치지형도에서 건축물 레이어를 추출한 후, 밀집도 분석을 위한 방사형 방안을 생성하였으며, 방안별로 건축물 높이별 도수분포 현황을 조사하였다. 건축물의 분포도를 통해 VMR(Variation-to-Means Ratio) 및 포아송분포 분석을 진행함으로써 높이별 밀집도를 판정하였으며, 카이제곱 검증을 통해 통계적 유의성을 확인하였다. 공간정보 분석을 바탕으로 GIS를 이용하여 연구를 진행함으로써 기존의 다소 정성적, 주관적인 방법에서 벗어나 지형 지물을 반영하여 보다 정량적, 객관적인 풍속고도분포계수의 산정이 가능하였다. 본 연구를 통해 설계자의 주관에 따라 풍속고도분포계수가 산정되는 기존의 문제점을 해결하고 보다 합리적인 내풍설계에 기여할 수 있을 것으로 기대된다.

• 전자공학회논문지
• /
• 제49권11호
• /
• pp.47-55
• /
• 2012

본 논문에서는 객체의 모션 블러(motion blur)를 포함하고 있는 다중시점(multi-view) 영상을 이용하여 객체의 3차원 형상 복원시 영상을 효과적으로 디블러링(deblurring)하여 3차원 형상 복원의 정확도를 높이는 기법을 제안한다. 다중시점 영상의 디블러링 수행시 다중시점 영상 간의 기하학적 상관관계를 고려하여 보다 정확히 PSF (point spread function)를 구함으로써 결과적으로 보다 정확한 3차원 형상 복원을 수행할 있다. 제안하는 기법은 각각의 입력 영상에서 초기 2D PSF를 독립적으로 구한 후, 3차원 PSF의 후보를 각 입력 영상의 카메라 행렬에 의해 투영했을 때 이들에 전역적으로 가장 잘 부합하는 3D PSF를 탐색한다. 3D PSF는 방향과 밀도 성분으로 구성되며 이는 결국 3차원 공간에서의 물체의 움직임 궤적과 동일하다. 추정된 3D PSF는 각 영상으로 다시 투영되어 각 영상의 2D PSF로 추정되고, 이에 의해 각 영상의 디블러링을 수행한다. 본 논문에서 제안하는 기법을 이용하여 다중시점 영상 디블러링과 3차원 형상 복원을 수행한 결과, 단일 영상만을 이용하여 복원할 경우에 비하여 디블러링과 3차원 형상 복원 모두 현저히 개선된 결과를 확인할 수 있다.

• 대한토목학회논문집
• /
• 제38권6호
• /
• pp.783-791
• /
• 2018

낮은 밀도의 강우관측망과 레이더 강우의 편향적인 추정은 좁은 지역에서 발생하는 돌발홍수에 대한 적용에는 한계가 있다. 이를 개선하기 위해서는 더 많은 강우정보의 생산이 필요하다. 본 연구에서는 최근에 개발되어 활용되고 있는 차량용 강우센서를 이용하여 적용성을 분석하였다. 개발된 강우센서를 차량에 부착하여 차량의 이동에 따른 강우 관측을 수행하였다. 분석 방법은 강우센서와 인근 강우관측소의 관측값에 대하여 시계열 및 평균 강수량을 이용하였다. 차량별로 부착된 센서(1~10번)의 관측 강우를 분석한 결과 전체적으로 센서별로 상대적으로 차이가 발생하고 있으나 강우 사상에 따른 관측값의 경향은 일정한 패턴을 나타내고 있는 것을 알 수 있었다. 이는 강우센서의 관측위치와 인근 강우관측소와의 거리 차이, 차량의 이동 속도, 강우관측 방법 등 다양한 원인에 의해 발생하는 것으로 분석되었다. 이 결과는 차량용 강우센서를 이용한 강우관측의 가능성을 보여주었으며 향후 다양한 조건에서의 실험 및 강우센서 개선을 통하여 보다 정밀한 강우관측이 가능할 것으로 검토되었다.

• 한국토양비료학회지
• /
• 제38권1호
• /
• pp.32-37
• /
• 2005

토양시료의 건조 과정이나 칭량과정을 수행하기 곤란한 현장 검정법에서 분석시료의 채취방법은 측정치의 신뢰성에 크게 영향을 미친다. 토양의 질산태 질소 함량이 45에서 $281mg\;kg^{-1}$으로 분포되는 12개 토양을 이용하여 질산태 질소 간이 검정법으로 효율적인 Test Strip 측광기 검정법에 대한 현장 활용성 증진방안이 비교 검토 되었다. 분석법은 실험실 전극법과 간이 측광기법으로 구분하고 채취방법은 중량법, 용적밀도법 (병마개 이용한 시료채취), 입자밀도법 (100 mL 실린더의 10 mL 용적을 토양으로 채움) 등 3가지 방법으로 비교하였으며, 또한 토양수분 조건은 풍건토, 최대용수량의 20% 및 40% 조건으로 달리하여 질산태 질소 함량의 상호관계를 평가하였다. Test strip 측광기법에 의한 질산태 질소 함량의 7반복 측정에서 변동계수(cv)는 3.5%에서 10.9%를 보이며 실험실 이온 전극법에 의한 질산태 질소 함량과 고도로 유의성 있는 상관을 보였다. 변동계수 10.9% 이하 재현성을 갖는 test strip 측광기법은 질산태질소의 현장검정법으로서 활용 가능한 것으로 생각되었다. 실험실 이온 전극법 뿐 아니라 test strip 측광기법에서 용적밀도법으로 측정된 질산태 질소 함량은 중량법 및 입자밀도법에 의한 측정치보다 표준 이온전극법에 의해 측정된 질산태 질소 함량과 더 근접되는 결과를 보였다. 이러한 결과는 토양의 수분함량이 높을수록 더욱 현저하여 용적밀도법의 의한 시료 채취방법은 토양의 수분조건에 의한 영향을 가장 적게 받는 것으로 확인되었다. 따라서 용적밀도법의 시료 채취용기를 병마개에서 보다 큰 용기로 교체한다면 test strip 측광기법에 의한 현장검정법의 활용성을 증진시킬 수 있을 것으로 생각되었다.

• Tuberculosis and Respiratory Diseases
• /
• 제50권4호
• /
• pp.415-425
• /
• 2001

배 경 : 폐기종의 중증도 판정에 있어서 병리학적 기준은 기강(air space)의 확장 정도에 있으며, 이는 고해상도 전산화 촬영 (high resolution computed tomography, HRCT)에 의해 결정되는 폐기종 점수(emphysema scoring)와 좋은 상관성을 보인다는 것은 주지의 사실이다. 한편 폐기종의 주증상은 운동성 호흡곤란이므로 폐기종에 대한 임상적 평가는 운동능력의 감소를 측정하는 것이 타당하다고 알려져 있다. 그러나 대개의 경우 폐기종의 중증도 판정은 안정시 폐기능 검사에 의존하는 경우가 흔하며, 병리학적 중증도 판정과 상관성이 높다고 알려져 있는 고해상도 전산화 촬영에 의한 폐기종 점수와 운동부하 폐기능검사 지표들과의 상관성 여부에 대한 연구는 드문 실정이다. 이에 본 연구에서는 폐기종의 중증도 판정에 있어서 HRCT와 안정시 폐기능 검사 및 운동부하 폐기능 검사간에 상호 관련성을 확인하여 보았다. 방 법 : 평균 연령 $60.6{\pm}10.3$세인 14명의 폐기종 환자들을 대상으로 HRCT, 안정시 폐기능 검사(forced expiratory flow volume curve, lung volumes by He dilution method, DLco, ABGA), 그리고 점진적운동부하폐 기능검사(incremental cycle ergometer)를 시행하였으며 HRCT는 GE highlight를 이용하여 조영증강 없이 최대흡기시에 1.5mm collimation, 10mm 간격으로 폐전체를 스캔하였고, 환자마다 모든 스캔에서 density mask를 이용하여 -400 HU를 기준으로 한 총폐면적과 -900 HU를 기준으로 한 폐기종 면적을 각각 구하여 백분율로 환산하여 폐기종 점수를 구하였다. 결 과 : 평균 폐기종 점수는 $37.4{\pm}14.9%$ 이었다. 폐기종 점수와 안정시 폐기능 검사의 DLco(r=-0.75)와 $PaO_2$(r=-0.66) 사이에서만 유의한(p<0.05) 상관성이 관찰되었다. 반면 폐기종 점수와 운동부하폐기능 지표들간의 상관성은 최대 산소섭취량(r=-0.68), 혐기성 역치(V-slope method, r=-0.690), 최대운동부하(r=-0.74), 최대운동시 $O_2$ pulse(r=-0.73), 최대운동시의 생리적 사강비율 (r=0.80) 등과 높은 유의성 (p<0.01)을 나타내었다. 그러나 호흡예비율과 심박수 예비율간에서는 유의한 상관성이 없었고, pulse oxymeter로 측정한 산소포화도와의 상관성도 유의하지 않았다. 결 론 : 이상의 결과에서 폐기종의 병리학적 중증도를 잘반영한다고 알려진 HRCT 폐기종 접수는 폐기종에 의한 생리학적 장애를 잘 반영하는 운동부하 폐기능 검사의 주요 지표들과 유의한 상관성이 있음을 확인할 수 있었다.