• Journal of radiological science and technology
• /
• v.26 no.4
• /
• pp.21-26
• /
• 2003

To evaluate the newly designed gastroduodenal coil catheter:in-vitro test. The coil catheter that we made in our laboratory was 150 cm. The coil that is made of stainless steel wire was composed 1.3 mm inner diameter and this coil spring was covered with heat-shrinkable polyethylene tube. To measure the length under fluorocopy, 8 radiopaque marks were attached at 5 cm, 10 cm, 11 cm, 12 cm, 13 cm, 14 cm, 15 cm, 20 cm apart from distal end of the catheter and 6, 2, 1 pores were made at 7 cm, 13 cm, 19 cm apart from the distal end. Radio-opacity and the amount of injected contrast was investigated in formerly used 5 Fr. vessel catheter, which is possible in measuring length, and newly designed coil catheter. Film density was tested for radio-opacity with autodensitometer. For measuring the volume of injected salin, the catheter was located in the acryl box(26 cm, 3 cm, 16 cm) that divided into 4 chambers. After injection 50 cc of contrast with autoinjector, the contrast's quantity in each chamber was measured with and without over the guide wire. Radio-opacity was 0.51 in 5 Fr. vessel catheter, 0.31 in newly made catheter. The amount of injected contrast was measured. In case of 5 Fr. vessel catheter, the amount was 99.5% from the distal part, there was no difference between with and without the guide wire. Otherwise, using a coil catheter, the pacentage the ejected saline was 1.17%, 18.8%, 41.8%, 38.2% from the distal part with the guide wire, 19.5%, 32.6%, 27.7%, 20.3% without the guide wire. Compare with formerly established catheter, this new coil catheter is easy to measure the length thanks to easy confirming under fluoroscopy and excellent in injecting contrast. Therefore, newly designed gastrointestinal catheter seems to be useful in gastrointestinal intervention procedure.

• Research in Plant Disease
• /
• v.21 no.2
• /
• pp.58-66
• /
• 2015

This study was conducted to evaluate control efficacy of a fermented food 'Cheonggukjang' against cucumber powdery mildew caused by Sphaerotheca fuliginea in greenhouse. Sterilized Daepung beans were inoculated with the rice straw as natural inoculum and then incubated for 72 hrs at $42^{\circ}C$ in the household cheonggkjang maker. After 72 hrs of cheonggukjang fermentation, white zymogens were grown on the surface of a sterile Daepung beans. The pH of the 72 hrs fermented soybean was not significantly changed and electrical conductivity was found to increase by about 2 times than before fermentation. The population density of soybean zymogen showed a peak of growth at 60 hrs after fermentation and the concentration of zymogen was $8.2{\times}10^7cfu/ml$. Soybean zymogen form of the colony was divided into three kinds of bacteria and a white and a large colony (WL) was predominant bacteria among those up to 60 hrs of fermentation. To control the cucumber powdery mildew, diluted solutions of cheonggukjang was applied from 6.0% to 30.0% on cucumber leaves and they showed injury symptoms on cucumber leaves in more than 15% of them. However, more than 6.0% diluted cheonggukjang solutions showed more than 77.8% control effect of cucumber powdery mildew at 15 days after treatment. The fermented bacteria of Chenggukjang were well established in the cucumber leaf area at 15 days after treatment. The antifungal activity of 10% diluted cheonggukjang solutions was excellent for four species of plant fungal pathogens, Colletotrichum gloeosporioides, Sclerotinia cepivorum, Rhizoctonia sloani and Phytophthora capsici in the dual culture test. Results indicated that foliar application of Cheonggukjang solution could be used for the control of powdery mildews occurring on organically cultivated cucumber.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.4
• /
• pp.385-390
• /
• 1999

HPLC method usually has been used for the determination of ATP and its related compounds in fish muscle and fish sauce. But, total amount of ATP related compounds in fish sauce is determined less than that of fish muscle. In order to establish the extract analysis method for ATP related compounds in fish sauce, a new enzymatic method was developed and compared with existing HPLC method. Fish sauce was extracted with chilled perchloric acid and neutralized to Ph 7.0 with potassium hydroxide solution, the extract was used as sample analyzed by HPLC as usual. On the other hand, for sample analyzed by enzymatic method, 1 ml extract solution was pipetted into test tube. To the tube, 0.5ml of mixed suspension adenosinedeaminase (4U), nucleosidephosphorylase (0.02U) and xanthineoxidase (0.03U) suspended in 2.0ml of 1/15 M sodium phosphate buffer solution pH 7.6 and 1.5ml deionized water wereadded for the decomposition of IMP, HxR and Hx to uric acid at $37^{\circ}C$ for 40 minutes. Total uric acid was determined by measuring optical density at 290nm. In HPLC method, salt decreased the total amount of ATP related compounds by $13.6\~16.2\%$ at $2.5\%$ concentration, but no effect in enzymatic method. IMP, HxR and Hx were detected at 254nm, while uric acid at only 290nm. The ratio of the total amount of ATP related compounds by HPLC method was about $45\%$ of that by enzymatic method in fish sauce. Form these results, enzymatic method is more accurate and simple than HPLC method for analysis of ATP related compounds in fish sauce.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.868-873
• /
• 2019

In this study, the evaluation of performance of AORFB using methyl viologen and TEMPOL as organic active materials in neutral supporting electrolyte (NaCl) with various membrane types was performed. Using methyl viologen and TEMPOL as active materials in neutral electrolyte solution, the cell voltage is 1.37V which is relatively high value for AORFB. Two types of membranes were examined for performance comparison. First, when using Nafion 117 membrane which is commercial cation exchange membrane, only the charge process occurred in the first cycle and the single cell couldn't work because of its high resistance. However, when using Fumasep anion exchange membrane (FAA-3-50) instead of Nafion 117 membrane, the result was obtained as the totally different charge-discharge graphs. When current density was $40mA{\cdot}cm^{-2}$ and cut off voltage range was from 0.55 V to 1.7 V, the charge efficiency (CE) was 97% and voltage efficiency (VE) was 78%. In addition, the discharge capacity was $1.44Ah{\cdot}L^{-1}$ which was 54% of theoretical capacity ($2.68Ah{\cdot}L^{-1}$) at $10^{th}$ cycle and the capacity loss rate was $0.0015Ah{\cdot}L^{-1}$ per cycle during 50 cycles. Through cyclic voltammetry test, it seems that this difference in the performance between the full cell using Nafion 117 membrane and Fumasep anion exchange membrane came from increasing resistance due to chemical reaction between membrane and active material, not the capacity loss due to cross-over of active material through membrane.

• Clean Technology
• /
• v.27 no.4
• /
• pp.332-340
• /
• 2021

With the recent reinforcement of emission standards, it is necessary to make efforts to reduce NOx from air pollutant-emitting workplaces. The NOx reduction method mainly used in industrial facilities is selective catalytic reduction (SCR), and the most commercial SCR catalyst is the ceramic honeycomb catalyst. This study was carried out to reduce the NOx emitted from steel plants by applying De-NOx catalyst coated on metallic monolith. The De-NOx catalyst was synthesized through the optimized coating technique, and the coated catalyst was uniformly and strongly adhered onto the surface of the metallic monolith according to the air jet erosion and bending test. Due to the good thermal conductivity of metallic monolith, the De-NOx catalyst coated on metallic monolith showed good De-NOx efficiency at low temperatures (200 ~ 250 ℃). In addition, the optimal amount of catalyst coating on the metallic monolith surface was confirmed for the design of an economical catalyst. Based on these results, the De-NOx catalyst of commercial grade size was tested in a semi-pilot De-NOx performance facility under a simulated gas similar to the exhaust gas emitted from a steel plant. Even at a low temperature (200 ℃), it showed excellent performance satisfying the emission standard (less than 60 ppm). Therefore, the De-NOx catalyst coated metallic monolith has good physical and chemical properties and showed a good De-NOx efficiency even with the minimum amount of catalyst. Additionally, it was possible to compact and downsize the SCR reactor through the application of a high-density cell. Therefore, we suggest that the proposed De-NOx catalyst coated metallic monolith may be a good alternative De-NOx catalyst for industrial uses such as steel plants, thermal power plants, incineration plants ships, and construction machinery.

• Composites Research
• /
• v.34 no.3
• /
• pp.192-198
• /
• 2021

Due to enormous market growing of electric vehicles without combustion engine, reducing unwanted BSR (buzz, squeak, and rattle) noise is highly demanded for vehicle quality and performance. Particularly, innerbelt weatherstrips which not only block wind noise, rain, and dust from outside, but also reduce noise and vibration of door glass and vehicle are required to exhibit high damping properties for improved BSR performance of the vehicle. Thermoplastic elastomers (TPEs), which can be recycled and have lighter weight than thermoset elastomers, are receiving much attention for weatherstrip material, but TPEs exhibit low material damping and compression set causing frictional noise and vibration between the door glass and the weatherstrip. In this study, high damping EPDM (ethylene-propylene-diene monomer)/PP (polypropylene) thermoplastic vulcanizates (TPV) were investigated by varying EPDM/PP ratio and ENB (ethylidene norbornene) fraction in EPDM. Viscoelastic properties of TPV materials were characterized by assuming that the material damping is directly related to the viscoelasticity. The optimum material damping factor (tanδ peak 0.611) was achieved with low PP ratio (14 wt%) and high ENB fraction (8.9 wt%), which was increased by 140% compared to the reference (tanδ 0.254). The improved damping is believed due to high fraction of flexible EPDM chains and higher interfacial slippage area of EPDM particles generated by increasing ENB fraction in EPDM. The stick-slip test was conducted to characterize frictional noise and vibration of the TPV weatherstrip. With improved TPV material damping, the acceleration peak of frictional vibration decreased by about 57.9%. This finding can not only improve BSR performance of electric vehicles by designing material damping of weatherstrips but also contribute to various structural applications such as urban air mobility or aircrafts, which require lightweight and high damping properties.

• Journal of Korean Society of Forest Science
• /
• v.111 no.4
• /
• pp.613-621
• /
• 2022

The study aim was to investigate changes in the diameter, number of standing trees, stand volume per ha and site index by the forest survey order, climate zone (northern temperate, central temperate, southern temperate, and warm temperate regions), and altitude in 100 m intervals) by collecting samples of Robinia pseudoacacia from the fifth, sixth, and seventh national forest survey datasets. The rotation cutting age, which is a standard used for wood, was calculated. The changes were statistically analyzed by performing ANOVA and the Duncan multiple test. Diameter growth naturally increased according to the forest survey order and was lowest in the southern temperate region by climate zone and lowest at the 301-400 m altitude. The number of standing trees per ha did not change according to the forest survey order and altitude, and the density was highest in the central temperate region and lowest in the southern temperate region. The stand volume per ha increased according to the forest survey order, and the climate zone was divided into two groups: ① northern temperate region and central temperate region, ② southern temperate region and warm temperate region. The stand volume growth was highest at the 201-300 m point. Thesite index showed results similar to the change pattern of the stand volume per ha. The growth curve, which can be seen by the change in stand volume per ha, was estimated by applying theWeibull formula, and the stand volume per ha was estimated to reach approximately 200 m³/ha at 50-60 years. The rotation of the highest production in volume, which is the standard for using trees as wood rather than honey sources, was calculated to be 34 years.

• Korean journal of applied entomology
• /
• v.24 no.2 s.63
• /
• pp.65-70
• /
• 1985

The locational preference of the brown planthopper (BPH) Nilaparvata lugens ($St{\aa}l$) and the whitebacked plant hopper (WBPH) Sogatella furcifera(Horvath) was studied on rice cultivars IR22 and IR36 as an integral part of subsequent research on insect-fungal pathogen relationships. The BPH was observed to stay consistently on the basal portion while the WBPH showed a general preference for the upper portion regardless of varieties, rice growth stages and insect population density levels. The habitat preference of both species (BPH and WBPH) was found not to be affected by the presence of the other species when both species are present on the same host plant Five rice cultivars with different reactions to BPH biotype 2 were used in the study on BPH-Rhizoctonia solani relationship: IR22 and TN1 (susceptible); Triveni and ASD7 (moderately resistant); and IR42 (resistant). Test plants were inoculated with R. solani (Kuhn) $3{\sim}4$days after insect infestation. Sheath blight disease severity/incidence was significantly higher in the treatment where BPH+R. solani were together than in the treatment with only the pathogen. Symptom expression of the disease in the BPH-pathogen combination was faster and mycelial growth was more profuse inducing the formation of more infection structures. Regardless of varietal reaction to BPH biotype 2, the degree of hopperburn was significantly higher in the combination of the two pests as compared with that of BPH alone. There could be a synergistic relationship between the insect pest and the pathogen indicated by a positive interaction between the two species.

• Journal of Environmental Impact Assessment
• /
• v.32 no.2
• /
• pp.123-133
• /
• 2023

Wastewater generated in the secondary battery production process contains lithium and high-concentration sulfate. Recently, as demand as demand for high-Ni precursors with high-energy density has surged, nickel emission is also a concern. Lithium and sulfate are not included in the current water pollutant discharge standard, so if they are not properly processed and discharged, the negative effect on future environment may be great. Therefore, in this study, the ecotoxicity of lithium, nickel, and sulfate, which are potential contaminants that can be discharged from the secondary battery production process, was evaluated using water flea (Daphnia magna) and luminescent bacteria (Aliivibrio fischeri). As a result of the ecotoxicity test, 24-hour and 48-hour D. magna EC₅₀ values of lithium were 18.2mg/L and 14.5mg/L, nickel EC50 values were 7.2mg/L and 5.4mg/L, and sulfate EC₅₀ values were 4,605.5mg/L and 4,345.0mg/L, respectively. In the case of D. magna, it was found that there was a difference in ecotoxicity according to the contaminants and exposure time (24 hours, 48 hours). Comparing the EC₅₀ of D. magna for lithium, nickel, and sulfate, the EC₅₀ of nickel at 24h and 48h was 39.6-37.2% compared to lithium and 0.1-0.2% compared to sulfate, which was the most toxic among the three substances. The difference appeared to be at a similarlevelregardless of the exposure time. The EC₅₀ of sulfate was 253.0-299.7% and 639.5-804.6%, respectively, compared to lithium and nickel, showing the least toxicity among the three substances. The 30-minute EC₅₀ values of luminescent bacteria forlithium, nickel, and sulfate were 2,755.8mg/L, 7.4mg/L, and 66,047.3mg/L,respectively. Unlike nickel, it was confirmed that there was a difference in sensitivity between D. magna and A. fischeri bacteria to lithium and sulfate. Studies on the mixture toxicity of these substances are needed.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.79-88
• /
• 2008

Recently, the high speed railway comes into the spotlight as the important and convenient traffic infrastructure. In Korea, Kyung-Bu high speed train service began in bout 400 km section in 2004, and the Ho-Nam high speed railway will be constructed by 2017. The high speed train will run with a design maximum speed of 300-350 km/hr. Since the trains are operated at high speed, the differential settlement of subgrade under the rail is able to cause a fatal disaster. Therefore, the differential settlement of the embankment must be controlled with the greatest care. Furthermore, the characteristics and causes of settlements which occurred under construction and post-construction should be investigated. A considerable number of studies have been conducted on the settlement of the natural ground over the past several decades. But little attention has been given to the compression settlement of the embankment. The long-term settlement of compacted fills embankments is greatly influenced by the post-construction wetting. This is called 'hydro collapse' or 'wetting collapse'. In spite of little study for this wetting collapse problem, it has been recognized that the compressibility of compacted sands, gravels and rockfills exhibit low compressibility at low pressures, but there can be significant compression at high pressures due to grain crushing (Marachi et al. 1969, Nobari and Duncan 1972, Noorany et al. 1994, Houston et al. 1993, Wu 2004). The characteristics of compression of fill materials depend on a number of factors such as soil/rock type, as-compacted moisture, density, stress level and wetting condition. Because of the complexity of these factors, it is not easy to predict quantitatively the amount of compression without extensive tests. Therefore, in this research I carried out the wetting collapse tests, focusing on various soil/rock type, stress levels, wetting condition more closely.