• Journal of the Korean Geotechnical Society
• /
• v.20 no.5
• /
• pp.127-134
• /
• 2004

Rammed Aggregate Pier (RAP) has extensive applicability as for a foundation of structures. In this study, bearing capacity of the reinforced ground by RAP and the failure behavior of RAP are investigated through experiments. RAPs with diameters of 45, 60, 70 mm were installed in sand, of which relative densities are 60, 70, 90%. Then, two columns of pressure gauges, near the RAPs and one diameter off from the center of piers, are installed 5, 10, 15, 20, 25, 30 cm from the surface of the ground. The test results show that maximum lateral earth pressure is observed near 5∼10 cm (1.0∼2.0D) from the surface, which indicates the occurrence of bulging failure type. In addition, deformation of RAP in radial direction increases with lower relative density of the ground. Furthermore, lateral stress distribution decreases with depth.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.2
• /
• pp.47-54
• /
• 1998

Refining is one of the most important processes of fiber treatment that provides optical and physical properties of final paper products. The evaluation method of refining progress is usually freeness (CSF) or wetness (SR) test because of its rapidity and convenience. However, there are some deficiencies in using freeness or wetness test to evaluate pulp fibers accurately because its results are more influenced by fines contents than extent of fibers treatment. The objective of this study is to show the deficiency of wetness in evaluating the refining process. For this, beating is done by varying the beating load. Handsheets are made after beating until 25 and $32^{\circ}C$ SR, and then paper properties are measured. Refined fibers are analyzed by fiber length, fines contents, curl, kink, WRV, and zero-span tensile strength. The results show that longer beating time is required to reach the same wetness at lower beating load. There are differences in the average fiber length, distribution curve of fiber length, fines contents, curl, kink, WRV of long fiber fraction, drainage time, and zero-span tensile strength of rewetted sample at different beating load. At the low beating load in the same wetness, apparent density, breaking length, burst strength, and tear strength are higher, while opacity and air permeability are lower than those of the high beating load. Using Page s equation, which shows the relationship among tensile strength, intrinsic fiber strength, and interfiber bonding strength, interfiber bonding strength is calculated and analyzed to explain final paper properties. At $25^{\circ}C$ SR, interfiber bonding strength is only slightly higher at 2.5kgf beating load, while the intrinsic fiber strength is substantially higher. At $32^{\circ}C$ SR, intrinsic fiber strength is a little bit higher at 2.5kgf beating load, and interfiber bonding strength is remarkably higher than those of 5.6kgf beating load. These results can be used to explain the different properties of the final paper at selected beating loads.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1259-1259
• /
• 2001

Meat becomes brown and rancid during storage in the refrigerator and display in the case. Color changes, metmyoglobin formation and lipid oxidation are the important problems in the transportation / distribution of meat and retail display. The freshness of meat is determined by the sense of vision and smell. Since conventional method determining lipid oxidation is time consuming and destructive (it needs to homogenize meat with reagents, filtrate, time for reaction and read optical density using spectroscopy), more rapid and nondestructive technical tools are desired. The objective of this work was to evaluate near-infrared spectroscopy as an analytical tool for determining meat color, metmyoglobin formation and lipid oxidation. in beef, pork and chicken. Semitendinosus and longissimus thoracis muscles from six beef steers, biceps femoris and longissimus thoracis muscles from twelve LWD crossbred pigs, and superficial pectoral muscles from twenty-four broilers were used. About a 5-cm diameter and 1-cm thick sample (20.0g) was cut from the muscle and placed on plastic foam, over-wrapped with PVC film, and displayed under flourescent lights at 4 degrees C. during 10 days for beef and pork or 4 days for chicken. The spectra was measured by NIR systems Model 5500 Spectrophotometer using fiber optic scan at range of 400 - 1100 nm. Data were recorded at 2 nm intervals and 10 scans / 10 sec were averaged for every sample. Data obtained were saved as log 1/Re, where Re is the reflectance energy, and then mathematically transformed to second derivatives to reduce effects of differences in particle size. $L^{*}$, $a^{*}$ and $b^{*}$, and metmyoglobin formation were determined by conventional spectrophotometer using the integrating sphere unit. 2-Thiobarbituric acid reactive substances (TBARS) were measured for lipid oxidation. A multiple linear regression was used to find the equation which would best fit the data. The number of wavelengths used in the equation was selected based on the fewer number compared to the increasing multiple correlation and Decreasing standard error. (omitted)

• Journal of Korea Game Society
• /
• v.4 no.4
• /
• pp.3-9
• /
• 2004

Expansion of internet and construction of high speed network which require multimedia services like MMORPG are exceeding the infra-structure. In this work, CBT is analyzed by focusing on the multicast routing protoco and the algorithm which is transformable to Anycast scheme from CBT scheme is suggested to adapt game traffic. Anycast routing scheme is suitable to distribute high density traffic. Simulation model was set per a number of group and group member, which enabled to reflect real environments. Performance evaluation of routing based on the characteristics of end-to-end delay of CBT and Anycast was mainly focused, The result showed that Anycast method was improved up 8.7%, 25.5%, 34.0%, 38.6% and 51.8%, 56.6% comparing with PIM-DM and CBT routing when packet site was 128, 512 and 1K byte respectively. From the simulation, CBT/Anycast routing scheme can be presented as a flexible and solid solution for the MMORPG traffic to improve the delay characteristics of game packets.

• Journal of Internet Computing and Services
• /
• v.6 no.3
• /
• pp.159-170
• /
• 2005

OC-SVM(One Class Support Vector Machine) avoids solving a full density estimation problem, and instead focuses on a simpler task, estimating quantiles of a data distribution, i.e. its support. OC-SVM seeks to estimate regions where most of data resides and represents the regions as a function of the support vectors, Although OC-SVM is powerful method for data description, it is difficult to incorporate human subjective importance into its estimation process, In order to integrate the importance of each point into the OC-SVM process, we propose a fuzzy version of OC-SVM. In FOC-SVM (Fuzzy One-Class Support Vector Machine), we do not equally treat data points and instead weight data points according to the importance measure of the corresponding objects. That is, we scale the kernel feature vector according to the importance measure of the object so that a kernel feature vector of a less important object should contribute less to the detection process of OC-SVM. We demonstrate the performance of our algorithm on several synthesized data sets, Experimental results showed the promising results.

• Structural Engineering and Mechanics
• /
• v.53 no.3
• /
• pp.481-495
• /
• 2015

Many hydropower stations in southwest China are located in regions of brittle rock mass with high geo-stresses. Under these conditions deep fractured zones often occur in the sidewalls of the underground caverns of a power station. The theory and methods of fracture and damage mechanics are therefore adopted to study the phenomena. First a flexibility matrix is developed to describe initial geometric imperfections of a jointed rock mass. This model takes into account the area and orientation of the fractured surfaces of multiple joint sets, as well as spacing and density of joints. Using the assumption of the equivalent strain principle, a damage constitutive model is established based on the brittle fracture criterion. In addition the theory of fracture mechanics is applied to analyze the occurrence of secondary cracks during a cavern excavation. The failure criterion, for rock bridge coalescence and the damage evolution equation, has been derived and a new sub-program integrated into the FLAC-3D software. The model has then been applied to the stability analysis of an underground cavern group of a hydropower station in Sichuan province, China. The results of this method are compared with those obtained by using a conventional elasto-plastic model and splitting depth calculated by the splitting failure criterion proposed in a previous study. The results are also compared with the depth of the relaxation and fracture zone in the surrounding rock measured by field monitoring. The distribution of the splitting zone obtained both by the proposed model and by the field monitoring measurements are consistent to the validity of the theory developed herein.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.434-441
• /
• 2010

Sodium polyacrylate (PAANa) was synthesized by inverse emulsion polymerization method to absorb excess water in concrete. Liquid paraffin was used as a continuous phase. Acrylic acid (AA) was neutralized by aqueous sodium hydroxide solution (8 M). Different amount of N,N'-methylene bisacrylamide (MBA) was used as a crosslinking agent to change crosslinking density of the synthesized PAANa. The size distribution of synthesized particles was measured by particle size analyzer. Swelling ratio of crosslinked PAANa was evaluated from the equation in D. I. water, cement aqueous solution, and $Ca(OH)_2$ aqueous solution. The FTIR spectroscopy was used to characterize $Ca^{2+}$ ion interaction with PAANa. Incorporation of 1.0 wt% PAANa into cement increased compressive and flexural strength approximately 30% and 10%, respectively, compared with those of ordinary portland cement.

• Journal of the Korean Dietetic Association
• /
• v.7 no.4
• /
• pp.361-372
• /
• 2001

This study was conducted to investigate the status of calcium intake and serum calcium level in perimenopausal women. The age distribution of the subjects was 49-55 years. Daily nutrient intake and dietary sources of calcium were analyzed by a convenient method and a food frequency questionnaire. At the same time, fasting blood samples were collected and serum calcium concentration was measured. The BMD of subjects was measured by Dual Energy X-ray Absorptiometry (DEXA). Fifty percent of the subjects under 50 years of age ($\leq$49 yr group) and 66.9% of the subjects from 50 years and up ($\geq$50 yr group) were classified as osteopenia or osteoporosis. Intake of energy (p<0.001), protein (p<0.05), fat (p<0.05), calcium (p<0.01) was significantly different between $\leq$49 yr group and $\geq$50 yr group. Mean daily intake of calcium was much lower than the Korean RDA : 94.9% in $\leq$49 yr group and 87.4% in $\geq$50 yr group. The average concentration of total calcium in serum was within the normal range in $\leq$49 yr group. Serum calcium concentrations were significantly (p<0.05) different between $\leq$49 yr group and $\geq$50 yr group. It was noteworthy that serum calcium concentration was positively related to the intake of protein, fat and calcium. Lettuce, sea mustard, bean-curd, anchovy, radish and perilla leaf was included among the major sources of dietary calcium. Further investigation is necessary to make sure of the relations between BMD and serum calcium level and calcium intake.

• Journal of Periodontal and Implant Science
• /
• v.26 no.4
• /
• pp.1003-1012
• /
• 1996

The induction of a phenotype with preoperties may have clinical significance in the acceleration of the wound-healing process. Wound contraction involves a specialized cell known as the myofibroblast. The myofibroblasts can be identified by their intense staining of actin bundles with anti-actin antibody. Tissue-specific actin distribution is correlated with the contractile activity of the myofibroblasts and smooth muscle etc. This study was performed to determine the expression of actin filaments in the cytoplasm of cultured human gingival fibroblsts after GaAs laser(BIOSAER, Korea) irradiation. Human gingival fibroblasts were cultured from explants of normal interdental gingival tissue. The third-generation fibroblasts were used for immunohistochemical study. The cultured fibroblasts were exposed $0.53joule/cm^2$(lmW, 7 mimutes) of energy density, and then observed by immunohistochemical method using, rabbit anti0gelsolin, hen smooth muscle polyclonal antibody(Chemicon international inc.), and biotinylated goat anti-rabbit IgG(Vectastain) 24-, 36-, 48-hour after laser irradiation Following results were obtained ; 1. In nonirradiated cultures, round shaped active fibroblasts with abundant cytoplasm and prominet nucleoli were observed. 2. In 24- and 36-hour cultures after laser irradiation, spindle shaped cells with long process were observed. The intensity of stain was seen in cytoplasm of these modified fibroblasts. 3. In 48-hoour cultures after laser irradiation, stained spindle shape cell were not observed. The results suggest that the effect of the galium-arsenide laser treatment on cultured gingival fibroblasts is the rapid development of cytoplasmic actin filaments.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.29-38
• /
• 1998

In this paper, we have induced a model for the growth and dissolution of oxygen precipitates which is generated during arbitrary thermal treatments or VLSI processes in CZ-grown silicon. Based on diffusion-limited growth law and detailed balance equilibrium theory, growth and dissolution rates are induced and inserted into a set of chemical rate equations and a Fokker-Planck equation. Then this is solved by numerical analysis. And because phenomenon at the silicon surface must be considered differently in various annealing conditions, in particular in $O_2$ ambient we have considered the growth model of SiO$_2$ at the surface of silicon wafer and the enhancement of oxygen solubility. By this method, oxygen depth profile and density distribution of oxygen precipitates are calculated more accurately than the other simulation results.