• International Journal of Highway Engineering
• /
• v.16 no.5
• /
• pp.29-38
• /
• 2014

PURPOSES : The purpose of this study is to evaluate moisture susceptibility of a dense graded and an open graded asphalt mixtures by the method of AASHTO T-283. METHODS : To simulate moisture damage of asphalt pavements with continuously rainfall during summer rainy season, the dense graded and the open graded asphalt mixtures were immersed in water for 15 days and were measured the weight and the change of strength. Also, the mixtures were performed five freeze-thaw cycles to simulate moisture damage of the mixtures by freeze-thaw during winter and were measured the change of strength. The degradation characteristics model was used to analyze the relationship between strength and moisture damage. RESULTS : According to the results, the dense graded and the open graded asphalt mixtures were shown in the similar trends of the strength changes by immersion time and freeze-thaw cycle. However, the moisture damage reduction of open graded asphalt mixture was more sensitive in early phase than that of dense graded asphalt mixture.

• International Journal of Highway Engineering
• /
• v.18 no.1
• /
• pp.57-62
• /
• 2016

PURPOSES : Reflection cracking has been one of the major causes of distress when asphalt pavement is laid on top of concrete pavement. This study evaluated the reflection cracking resistance of asphalt mixtures reinforced with asphalt embedded glass fiber and carbon fiber using a Texas Transportation Institute (TTI) overlay tester. METHODS : Different asphalt mixtures such as polymer-modified mastic asphalt (PSMA) and a dense graded asphalt mixture were reinforced with asphalt-embedded carbon fiber and glass fiber. For comparison purposes, two PSMA asphalt mixtures and one dense graded asphalt mixture were evaluated without fiber reinforcement. Two different overlay test modes, the repeated overlay test (R-OT) and monotonic overlay test (M-OT), were used to evaluate the reflection cracking resistance of asphalt mixtures at $0^{\circ}C$. In the R-OT test, the number of repeated load when the specimen failed was obtained. In the M-OT test, the tensile strength at the peak load and tensile strain were obtained. RESULTS : As expected, the fiber-reinforced asphalt mixture showed a higher reflection cracking resistance than the conventional nonreinforced asphalt mixtures based on the R-OT test and M-OT test. The dense graded asphalt mixture showed the least reflection cracking resistance and less resistance than the PSMA. CONCLUSIONS : The TTI overlay tester could be used to differentiate the reflection cracking resistance values of asphalt mixtures. Based on the R-OT and M-OT results, the carbon-fiber-reinforced asphalt mixture showed the highest reflection cracking resistance among the nonreinforced asphalt mixtures and glass-fiber-reinforced asphalt mixture.

• Journal of the Society of Disaster Information
• /
• v.7 no.1
• /
• pp.32-42
• /
• 2011

Many researches have been conducted to evaluate the performance of modified asphalt concrete mixtures. The research was conducted to estimate the laboratory mechanical characteristics of Elvaloy-modified asphalt concrete mixture. To achieve its intended objective, indirect tensile test and resilient modulus test were performed. The rest results revealed that indirect tensile strengths and resilient moduli of the Elvaloy-modified asphalt concrete mixture were higher than those of the conventional dense-graded. As a result, within the limits of the tests conducted in this research, it is predicted that the performance and stability of the Elvaloy-modified asphalt concrete mixture are better than that of the conventional dense-graded one.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4832-4836
• /
• 2012

In general, there are needed lots of time and experiments for determination of optimum asphalt content and mix design. The experimental results are highly depended on the skill of testers. Bailey suggested the proper aggregate gradation of hot mix asphalt are a function of special size and passing percent of the specified aggregate to reduce the test errors. In this paper, the asphalt mix designs of 19mm dense graded mix and PA-20mm for FHWA were carried out, using Bailey's method. The use of Bailey method can cut down the testing times to get the proper aggregate gradation for asphalt mix design. In case of 19mm dense graded asphalt mixture, the measured values of CA, $FA_c$, $FA_f$ are 0.724, 0.440, and 0.455, which are within the suggested values by Bailey. Also, in case of PA-20 graded asphalt mixture, the measured values of CA, $FA_c$, $FA_f$ are 0.646, 0.476, and 0.450, respectively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.6
• /
• pp.1367-1375
• /
• 2015

The purpose of this paper is to suggest 10 mm aggregate specification for thin layer asphalt pavement using steel slag. Aggregate gradations of conventional dense-graded asphalt mixtures were made by fuller's model, whereas 10 mm dense-graded asphalt mixture was obtained tender mix due to close to the maximum density line. The proposed aggregate gradation specification was made to have enough VMA and well-interlocking refer to foreign standards. The correlation between the proposed aggregate gradation and the properties of mixtures were analyzed using Gradation Ratio (GR) and Compacted Aggregate Density (CAD). The CAD index has a high $R^2$ of 0.86-0.99 because the CAD index is able to reflect various aggregate properties. As the results of evaluation by CAD index the proposed aggregate gradation provides more reliable stability and VMA. The percent passing (%) of aggregate size smaller than 0.3 mm was limited 10% or more for improving crack resistance. This limitation increased for 15% of the asphalt mixture's toughness.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.5
• /
• pp.88-95
• /
• 2002

This study is a fundamental research for recycling waste vinyl (WV) in asphalt mixture for improving roadway pavement. Mix design was conducted by WV content and optimum asphalt content (OAC) was determined for dense-graded surface course mixture. Marshall stability test, indirect tensile strength (ITS) test and wheel tracking test were carried out to measure the characteristics of WV-added asphalt concretes. From the results of this study, recycling WV in asphalt mixture is possible. However, as WV content increased, melted WV clustering appeared in asphalt mixture. It could be considered that adding too much WV in asphalt mixture is not proper. The proper content of LDPE and HDPE WV was appeared to be 12% and 8%, respectively.

• International Journal of Highway Engineering
• /
• v.4 no.1 s.11
• /
• pp.161-170
• /
• 2002

This study is a fundamental research for recycling waste polyethylene film(WPF) in asphalt concrete for roadway pavement. The objective of this study is to develop technology of making waste polyethylene asphalt mixture and evaluate properties of the asphalt concrete containing WPF. Asphalt concrete for surface course of pavement was produced through an appropriate mix-design using dense-graded and gap-graded aggregates. Marshall mix design, indirect tensile strength test, wheel tracking test and tensile fatigue test were performed. Test result showed that some WPF asphalt mixtures had a high tensile property and good resistances against rutting and fatigue cracking, compared with normal asphalt mixture.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.9-14
• /
• 2012

In this study, the profiles of asphalt pavements were measured using a lightweight profiler and depths of macrotexture were analyzed based on the measured profiles. Profiles on dense graded asphalt pavement, prorous asphalt pavement, stone mastic asphalt (SMA) pavement, and base layer measured, and depth of macrotexture were calculated and analyzed. Profiles on the pavement that happened as asphalt mixture segregation were measured and depths of macrotexture were analyzed. The results showed that the depths of macrotexture of asphalt pavement were effectively calculated using the measured profiles, and the depths of macrotexture for different asphalt pavements were analyzed. The pavement areas which have asphalt mixture segregation were detected based on analysis of macrotexture depths.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.732-737
• /
• 2016

Using the pyrolyzed carbon black (PCB) from waste tires, the performance of 13 mm dense-graded hot mix asphalt was evaluated. The Marshall mix design was carried out and the measured optimal asphalt content was 5.8%. The impact resonant test was conducted to obtain the elastic modulus and damping ratio of the hot mix asphalt. The elastic modulus of HMA increased with increasing amount of PCB. On the other hand, there was no significant change in the damping ratio. The Marshall mix design, indirect tensile test, permanent deformation test, and program analysis were carried out. The strength ratio of the PCB modified asphalt mixtures was within 10%. More 10% of PCB was not good for the permanent deformation of hot mix asphalt. From the pavement design program, the use of 5% PCB in hot mix asphalt showed a decrease in the top-down crack, bottom-up crack, and permanent deformation. Judging from the limited test and analysis, the use of 5% PCB is good for enhancing the pavement performance.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.2 no.3 s.6
• /
• pp.79-88
• /
• 2002

The main purpose of this paper is to evaluate the possibility of improvement in fatigue resistance of asphalt concrete mixture using the industrial waste material of K fiber. In this research, as an experimental equipment, the MTS with Closed-Loop Servohydraulic System was used and it was designed according to the U.S. standard testing procedure of ASTM D 4123. According to the test results, the optimum content of fiber with the length of 8mm was about 0.2 percent of total mixture weight. The optimum asphalt content for the fiber-reinforced asphalt concrete was about 5.5 percent of total mixture weight. Fatigue resistance of fiber-reinforced asphalt concrete was noticeable compared to the conventional dense-graded 20 asphalt concrete. In addition, the resilient moduli of fiber-reinforced asphalt mixture were $1.15{\sim}1.18$ times higher than those of conventional asphalt concrete.