• Restorative Dentistry and Endodontics
• /
• v.27 no.1
• /
• pp.77-86
• /
• 2002

Current composites are made with dimethacrylate monomers and silane-treated silica microfillers, either alone or with silane treated glass fillers The main reasons for clinical failure of dental composites are secondary caries, wear and fracture. Most of practitioner want to get a composite which is more tougher under occlusal stress, less polymerization contraction, and better handling properties in application clinically. The aim of this study was to investigate the influence of resin matrix with various flows on the physical proper-ties such as fracture toughness and degree of conversion of the experimental resins. It was hypothesized that flexible or tough resin composites can be designed by judicious choice of monomer composition Various flow resin matrices containing Bis-GMA, UDMA, and TEG-DMA were made by altering the pro-portion of the monomers. After the unfilled resins were light-cured for different light intensity, the fracture toughness(K$_{1c}$) was measured according to ASTM standard using the single edge notched geometry, and degree of conversion(DC) was measured by FTIR. And experimental composites were formulated with variations in the proportion of silanated quartz and strontium glass fillers as 60, 75, and 77wt%. Also, the physical properties of composites with various filer contents were evaluated as same manner. All resulting data were compared by ANOVA/Tukeys test at 0.05 level. The results were as follows; 1. The degree of conversion of high flow resin containing less Bis-GMA was higher than that of low flow unfilled resin 2. While the degree of conversion of unfilled resin was increased according to light intensity for polymerization, there was no significant increase with moderate and high light intensity. Also, the fracture toughness was not increased by high light intensity. 3. The fracture toughness was high in the low flow unfilled resin containing higher contents of Bis-GMA. 4. There was a significant increase for fracture toughness and a tendency for degree of conversion to be reduced when the content of fillers was increased. 5. In the experimental composites, the flow of resin matrix did not affected on the fracture toughness, even, which was decreased as increase of viscosity. These results showed that the physical properties of a dental composite could be attributed to the flow of resin matrix with relative content of monomers. Specific combination of resin monomers should be designed to fulfil the needs of specific indication for use.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.5 no.1
• /
• pp.27-30
• /
• 1981

The change of physical properties of polyester yarn treated with sodium hydroxide solution for making polyester silk like was investigated. The tenacity of polyester yarn was reduced by increasing alkali concentration and temperature. Degree of polymerization of polyester was decreased slightly but the heat of fusion was not changed appreciably.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.130-134
• /
• 1998

The physical properties of poly(vinyl alcohol) (PVA) are highly dependent on the degree of syndiotacticity, which is determined primarily by the choice of the vinyl ester monomer precursor. Efforts to produce more syndiotactic PVAs, as well to increase the molecular weight, have centered on the polymerization of vinyl trifluoroacetate,$^1$ vinyl trichloroacetate,$^2$ and vinyl pivalate (VPi).(omitted)

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.583-586
• /
• 2000

Many different oligosaccharides were produced by transferring the fructose residue of sucrose to maltose, cellobiose, lactose and sucrose (self-transfer), where their yields of fructosylated acceptor products accounted for $26{\sim}30%$ (w/w). The maximum conversion yield (30%) was obtained in fructosyl cellobioside formation with 500 g sucrose/l (substrate) and 200 g cellobiose/l (acceptor). These four acceptors gave various products having DP (degree of polymerization) $2{\sim}7$ by successive transfer reactions.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.287-292
• /
• 2002

Graft copolymerization of styrene and glycidyl methacrylate (GMA) to the peroxidized polypropylene (PP) fabric with E-beam in $O_2$ atmosphere was carried out in vapor phase with benzoyl peroxide (BPO) as an initiator. The degree of grafting of copolymers was increased with the increase of the reaction temperature and the highest degree of grafting was obtained at $70^{\circ}C$ with styrene, and at $80^{\circ}C$ with GMA. The highest degree of grafting of styrene grafted PP according to reaction time was higher than that of GMA grafted PP. In vapor phase graft polymerization, the degree of grafting of copolymers according to water composition in monomer mixture was effected by the boiling temperature of monomers.

• Restorative Dentistry and Endodontics
• /
• v.29 no.4
• /
• pp.386-398
• /
• 2004

Objectives: The purpose of this study was to observe the reaction kinetics and the degree of polymerization of composite resins when cured by different light sources and to evaluate the effectiveness of the blue Light Emitting Diode Light Curing Units (LED LCUs) compared with conventional halogen LCUs. Materials and Methods: First, thermal analysis was performed by a differential scanning calorimeter (DSC). The LED LCU (Elipar Freelight, $320{\;}mW/\textrm{cm}^2$) and the conventional halogen LCU (XL3000, $400{\;}mV/\textrm{cm}^2$) were used in this study for curing three composite resins (SureFil, Z-250 and AEliteFLO). Second. the degree of conversion was obtained in the composite resins cured according to the above curing mode with a FTIR. Third, the measurements of depth of cure were carried out in accordance with ISO 4049 standards. Statistical analysis was performed by two-way ANOVA test at 95% levels of confidence and Duncan's procedure for multiple comparisons. Results: The heat of cure was not statistically different among the LCUs (p > 0.05). The composites cured by the LED (Exp) LCUs were statistically more slowly polymerized than by the halogen LCU and the LED (Std) LCU (p < 0.05). The composite resin groups cured by the LED (Exp) LCUs had significantly greater degree of conversion value than by the halogen LCU and the LED (Std) LCU (p =0.0002). The composite resin groups cured by the LED (Std) LCUs showed significantly greater depth of cure value than by the halogen LCU and the LED (Exp) LCU (p < 0.05).

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.6
• /
• pp.639-643
• /
• 2008

STATEMENT OF PROBLEM: The degree of conversion may influence the ultimate mechanical and physical properties of provisional crown and fixed partial denture materials. The high levels of the unreacted residual monomer may cause deleterious effect on the properties. PURPOSE: The purpose of this study was to measure the degree of conversion of bis-acrylic based provisional crown and fixed partial denture materials by using an infrared spectroscopic method. MATERIAL AND METHODS: Chemically activated three bis-acrylic based provisional crown and fixed partial denture materials, LuxaTemp [DMG, Hamburg, Germany], fast set TemPhase [Kerr, Orange, CA, USA] and Protemp 3 Garant [3M-ESPE, St Paul, MN, USA], were investigated by Fourier transform infrared spectrometry (FTIR). The FTIR spectra of the materials tested were immediately obtained after mixing. The specimens were stored under dry conditions and at $23^{\circ}C$ for 24 hours, and then the spectra of the materials were also obtained. The degree of conversion (%) was calculated from the spectrum of the absorbance between the aliphatic double bond at 1637 $cm^{-1}$ and the aromatic double bond at 1608 $cm^{-1}$ using the baseline method. The data were statistically analyzed using one-way ANOVA and the multiple comparison Scheffe test at the significance level of 0.05. RESULTS: The mean value and standard deviation of the degree of conversion were 52.5 % ${\pm}$ 1.1 %, 50.3 % ${\pm}$ 0.8 %, and 42.3 % ${\pm}$ 4.9 % for LuxaTemp, Protemp 3 Garant and fast set TemPhase, respectively. There was no significant difference between LuxaTemp and Protemp 3 Garant, whereas there was a statistically difference between Protemp 3 Garant and fast set TemPhase, and LuxaTemp and fast set TemPhase (P < .05). CONCLUSION: The degree of conversion of fast set TemPhase was significantly lower than those of the others. The degree of conversion may be correlated with the rate of polymerization.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.82-86
• /
• 1996

This study was performed to elucidate the effect of degree of substitution and degree of polymerization of CMC on the rheological characteristics of coating color which is consisted of calcium carbonate as pigment. The results were as follows: 1. It appeared that DP of CMC rather DS has an effect on the low shear viscosity of coating color. 2. According as shear rate increased, the effect of DP and DS on high shear viscosity of coating color decreased. 3. According to increasing DS and DP, the water retention of coating color increased.

• Proceedings of the KACD Conference
• /
• 2001.11a
• /
• pp.558.2-558
• /
• 2001

The aims of this study are (1) to investigate the relation of irradiation mode, polymerization shrinkage and degree of cure of composite resin and(2) it effect on micorleakage of class V restorations. VIP(BISCO Dental Products, Schaumburg, IL, USA) and Optilux 501 (Demetron/Kerr, Danbury, CT, USA) curing lights were used for curing Z-250 composite resin following irradiation mode: VIP 200㎽d, VIP 400㎽, VIP 600㎽, pulse-delay(200㎽ 3sec, 5min wait, 600㎽ 30sec), Optilux R mode.(omitted)

• Journal of Sericultural and Entomological Science
• /
• v.42 no.2
• /
• pp.104-108
• /
• 2000

To hydrolyze insolule sericin the enzyme hydrolysis was used, and then obtained the results as given belows. When insoluble sericin was hydrolyzed by enzyme treatment, the solubility was best at pH 7, 60$\^{C}$ and was slightly increased both above 2 hours treatment and above 10% of enzyme concentration. As the results of electrophoresis, the distribution of molecular weight of sericin powder obtained by enzyme hydrolysis was very weak and showed in the wide range having no distinguishable band. Average degree of polymerzations (A.D.P.) of sericin hydrolyzed by enzyme were about 4.1∼6.3, average molecular weight were about 470∼730. The whiteness of the sericin powder obtained by enzyme hydrolysis was high and increased slightly with higher treatment concentration of enzyme. As the results of amino acid analysis, the amino acid analysis, the amino acid composition of the sericin powder from the enzyme treatment were similar to which located at near 230$\^{C}$ and 320$\^{C}$. The peak of near 230$\^{C}$ could not been found in the sericin powder obtained by enzyme hydrolysis.