• International Journal of Concrete Structures and Materials
• /
• v.11 no.1
• /
• pp.1-16
• /
• 2017

The compression or tension-controlled failure mode of concrete beams prestressed with unbonded FRP tendons is governed by the relative amount of prestressing tendon to the balanced one. Explicit assessment to determine the balanced reinforcement ratio of a beam with unbonded tendons (${\rho}^U_{pfb}$) is difficult because it requires a priori knowledge of the deformed beam geometry in order to evaluate the unbonded tendon strain. In this study, a theoretical evaluation of ${\rho}^U_{pfb}$ is presented based on a concept of three equivalent rectangular curvature blocks for simply supported concrete beams internally prestressed with unbonded carbon-fiber-reinforced polymer (CFRP) tendons. The equivalent curvature blocks were iteratively refined to closely simulate beam rotations at the supports, mid-span beam deflection, and member-dependent strain of the unbonded tendon at the ultimate state. The model was verified by comparing its predictions with the test results. Parametric studies were performed to examine the effects of various parameters on ${\rho}^U_{pfb}$.

• Structural Engineering and Mechanics
• /
• v.39 no.2
• /
• pp.169-186
• /
• 2011

This paper is devoted to the development of the equations which describe the elastic response of a curved laminate subjected to in-plane loads and bending moments. Similar to the classic $6{\times}6$ ABD matrix constitutive relation of a flat laminate, a new $6{\times}6$ matrix constitutive relation between force resultants, moment resultants, mid-plane strains and deformed curvatures for a curved laminate is formulated. This curved lamination theory will provide the fundamental basis for the analyses of curved laminated structures. The stress predictions by the present curved lamination theory are compared to those by the curved laminate analysis that neglected the nonlinear terms in the derivation of the constitutive relation. The results show that the curved laminate analysis that neglected the nonlinear terms cannot reflect the effect of curvature and can no longer predict the stresses accurately as the curvature becomes noticeable. In this paper, a curved lamination theory that retains the nonlinear terms and, therefore, accounts for the effect of the non-flat geometry of the structure will be developed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1692-1696
• /
• 2004

This paper presents the thermally induced hot spot characteristics of rubbing surface in the friction pad disk brake. During the braking period, the rubbing surface with irregular asperities that are strongly engaged in rough surface, wear, and deformed surface due to a friction heating may produce an irregular distorted geometry of the disk surface. The tribological interactions between the disk and the pads are unstable if the contact stress is severe, in which the irregularity develops the contact pressure distribution, leading eventually to localized contact, high temperature and formation of hot spots. The computed results of contact spots that are simulated using a coupled thermal-mechanical analysis present sinusoidal distortions and localized extrusions of the disk surface, which are strongly related to a hot spot in the practical disk brake.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.183-184
• /
• 2006

Densification behavior of iron powder under cold stepped compaction was studied. Experimental data were also obtained for iron powder under cold stepped compaction. The elastoplastic constitutive equation based on the yield function of Shima and Oyane was implemented into a finite element program (ABAQUS) to simulate compaction responses of iron powder during cold stepped compaction. Finite element results were compared with experimental data for densification, deformed geometry and density distribution.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.5
• /
• pp.452-457
• /
• 1996

The effects caused by the ionization on the electronic structure and geometry on C60 are studied by the modified Su-Schriffer-Heeger (SSH) model Hamiltonian. After the ionization of C60, the bond structure of the singly charged C60 cation is deformed from Ih symmetry of the neutral C60 to D5d, C1, and C2, which is dependent upon the change of the electron-phonon coupling strength. The electronic structure of the C60+ cation ground state undergoes Jahn-Teller distortion in the weak electron-phonon coupling region, while self-localized states occur in the intermediate electron-phonon region, but delocalized electronic states appear again in the strong electron-phonon region. In the realistic strength of the electron-phonon coupling in C60, the bond structure of C60+ shows the layer structure of the bond distortion and a polaron-like state is formed.

• Nuclear Engineering and Technology
• /
• v.49 no.7
• /
• pp.1524-1536
• /
• 2017

During the fabrication process of reactor vessel head penetration (RVHP), the grain size of the tube material can be changed by hot or cold work and the inner side of the tube can also be shrunk due to welding outside of the tube. Several nonregular time-of-flight diffraction (TOFD) signals were found because of deformed grains. In this paper, an investigation of nonregular TOFD indications acquired from RVHP tubes using experiments and computer simulation was performed in order to identify and distinguish TOFD signals by coarse grains from those by Primary Water Stress Corrosion Crack (PWSCC). For proper understanding of the nonregular TOFD indications, microstructural analysis of the RVHP tubes and prediction of signals scattered from the grains using Finite Element Method (FEM) simulation were performed. Prediction of ultrasonic signals from the various sizes of side drilled holes to find equivalent flaws, determination of the size of the nonregular TOFD indications from the coarse grains, and experimental investigation of TOFD signals from coarse grain and shrinkage geometry to identify PWSCC signals were performed. From the computer simulation and experimental investigation results, it was possible to obtain the nonregular TOFD indications from the coarse grains in the alloy 690 penetration tube of RVHP; these nonregular indications may be classified as PWSCC. By comparing the computer simulation and experimental results, we were able to confirm a clear difference between the coarse grain signal and the PWSCC signal.

• Smart Structures and Systems
• /
• v.20 no.4
• /
• pp.441-450
• /
• 2017

The objective of this work is to present a conceptual design and the modelling of a distributed sensor system based on fiber optic devices (Fiber Bragg Grating, FBG), aimed at measuring span-wise and chord-wise variations of an adaptive (morphing) trailing edge. The network is made of two different integrated solutions for revealing deformations of the reference morphing structure. Strains are confined to typical values along the span (length) but they are expected to overcome standard ranges along the chord (width), up to almost 10%. In this case, suitable architectures may introduce proper modulations to keep the measured deformation low while preserving the information content. In the current paper, the designed monitoring system combines the use of a span-wise fiber reinforced patch with a chord-wise sliding beam. The two elements make up a closed grid, allowing the reconstruction of the complete deformed shape under the acceptable assumption that the transformation refers to regular geometry variations. Herein, the design logic and some integration issues are reported. Preliminary experimental test results are finally presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.123-137
• /
• 1998

The finite deformation with self contact problem of C. V. joint boots is analysed by using the implicit finite element code ABAQUS/Standard. It is shown that analysis results have a good agreement with experimental ones to the degree of maximum rotation angle. As an application of design modification, the effects of thickness change of the rounded part of boot model on the bending and the contact situation of deformed geometry are investigated. In this paper, the effect of the design modification in the end on the leakage is examined using 2-D finite element simulation. To solve the leakage problem of grease, the length of the small end is enlarged. From this study, it is confirmed that we can save the cost and time by applying FEM techniques to analyze and design the boot model.

• International Journal of Automotive Technology
• /
• v.1 no.1
• /
• pp.35-41
• /
• 2000

The crashworthiness of vehicles with finite element methods depends on the geometry modeling and the material properties. The vehicle body structures are generally composed of various members such as frames, stamped panels and deep-drawn parts from sheet metals. In order to ensure the impact characteristics of auto-body structures, the dynamic behavior of sheet metals must be examined to provide the appropriate constitutive relation. In this paper, high strain-rate tensile tests have been carried out with a tension type split Hopkinson bar apparatus specially designed for sheet metals. Experimental results from both static and dynamic tests with the tension split Hopkinson bar apparatus are interpolated to construct the Johnson-Cook and a modified Johnson-Cook equation as the constitutive relation, that should be applied to simulation of the dynamic behavior of auto-body structures. Simulation of auto-body structures has been carried out with an elasto-plastic finite element method with explicit time integration. The stress integration scheme with the plastic predictor-elastic corrector method is adopted in order to accurately keep track of the stress-strain relation for the rate-dependent model accurately. The crashworthiness of the structure with quasi-static constitutive relation is compared to the one with the rate-dependent constitutive model. Numerical simulation has been carried out for frontal frames and a hood of an automobile. Deformed shapes and the Impact energy absorption of the structure are investigated with the variation of the strain rate.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.156-162
• /
• 2005

In this paper, we study the mechanism of lead deformation by numerically simulating the stamping process by means of a commercial finite element code. It is very important to analyze effects that the lead shape makes on the lead deformation, because the lead shape is often modified in order to minimize the deformation or to increase the buckling critical load of the punch. Therefore the stamping process, first, numerically simulated by considering as a quasi-static problem. Second, the effect on the lead deformation due to the lead shape variation, a linear lead geometry and a bent lead, was numerically analyzed and discussed. Finally, the punching order was optimized fur multi-lead generating stamping process. The results show that the bent lead is little bit more shifted than the linear lead after the punching process. But the bent lead is vertically less deformed than the linear lead. The punching order to successively generate the lead is good to keep the lead space uniform. The results will be very effectively applied for the design of the blanking or punching dies in industry.