• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1295-1302
• /
• 2003

In order to evaluate a failure behavior of pipe with notch-type wall thinning, the present study performed full-scale pipe tests using the 102mm, Schedule 80 pipe specimen simulated notch- and circular-type thinning defects. The pipe tests were conducted under the conditions of both monotonic and cyclic bending moment at a constant internal pressure of 10 MPa. From the results. of experiment the failure mode, load carrying capacity, deformation ability, and fatigue life of a notch-type wall thinned pipe were investigated, and they were compared with those of a circular-type wall thinned pipe. The failure mode of notched pipe was similar to that of circular-type thinned pipe under the monotonic bending load. Under the cyclic bending load, however, the mode was clearly distinguished with variation in the shape of wall thinning. The load carrying capacity of a pipe containing notch-type wall thinning was about the same or slightly lower than that of a pipe containing circular-type wall thinning when the thinning area was subjected to tensile stress, whereas it was higher than that of a pipe containing circular-type thinning defect when the thinning area was subjected to compressive stress. On the other hand, the deformation ability and fatigue life of a notch-type wall thinned pipe was lower than those of a circular-type wall thinned pipe.

• 자원환경지질
• /
• 제24권2호
• /
• pp.177-186
• /
• 1991

Ogchon Supergroup directly contacts with Choseon Supergroup in the northern area of Worak-san, where evidences indicating thrust-fault formed during $D_2$-deformation are observed. On footwall of thrust fault, calcite veins in Gounri Formation belonging to Choson Supergroup may be deformed during thrust faulting($D_2$). Calcite veins are parallel to axial plane cleavage($S_2$) of $F_2$ fold and truncate slaty cleavage($S_1$). Therefore, we can use deformation twins in calcite grains of the veins as a marker for inferred differential stress operated upon thrust faulting. The inferred differential stresses are estimated at 190 Mpa from K, sample. The stress from K, sample close to the contact between Ogchon Supergroup and Choseon Supergroup shows a higher value than $K_2$-$K_6$ samples, probably having an important influence upon thrust faulting. The differential stress reveal again high value at $K_7$ sample, which may suggest the presence of another thrust fault.

• 화약ㆍ발파
• /
• 제37권2호
• /
• pp.1-13
• /
• 2019

본 연구에서는 도심지 발파에서 형성되는 분할 단면의 변형을 확인하기 위해 Visual FEA 유한요소 프로그램으로 발파 단면을 모델링하여 발파 기폭 패턴에 따른 최대주변형률을 분석하였고, Visual FEA 유한요소 프로그램으로 분석된 분할 단면과 현장 발파로 형성된 분할 단면을 비교하였다. 결과적으로, 발파 기폭 패턴에 따라 분할 단면에서 최대주변형률의 차이를 나타냈고, 전산해석과 현장 발파에서 분할 단면이 유사한 파형 형태를 보이는 것으로 확인되었다.

• 한국지반공학회논문집
• /
• 제24권8호
• /
• pp.53-60
• /
• 2008

본 연구에서는 균질 지반에 매설된 단독말뚝에 수평하중이 작용할 경우 말뚝 배면지반에서 발생되는 여러 가지 거동 특성, 즉 말뚝 배면지반의 변형영역, 파괴면의 경사각, 그리고 회전절점과 같은 거동 특성을 모형실험을 통하여 규명하고자 모형실험을 수행하였다. 이는 말뚝의 휨력에 대한 저항력 산정에 매우 중요한 사항이다. 그 결과 다음과 같은 결과를 얻을 수 있었다. 수평하중이 작용하는 단독말뚝 배면지반에서 쐐기 파괴면은 거의 선형적인 거동 특성을 나타내고, 말뚝과 파괴면이 이루는 경사각은 말뚝 길이, 말뚝 두부의 변위에 상관없이 지반의 상대밀도 증가에 따라 조금씩 증가하다 일정한 값으로 수렴하는 경향을 나타낸다.

• 한국농촌건축학회논문집
• /
• 제24권2호
• /
• pp.53-61
• /
• 2022

In order to understand the physical condition and spatial deformation of houses in rural areas in Hodang Village, Ipjang-myeon, Cheonan-si, a rural area with a good settlement environment, physical characteristics and spatial deformation were identified. First, looking at the construction pattern of houses in rural areas, there have been many houses built since the 1990s, and the modernized spatial composition of urban houses appeared. Second, due to the nature of rural housing, work space and residential space are mixed, and it was analyzed that space is used through renovation to solve this problem. Third, Hodang Village was analyzed as an area with good living services, but as a result of the village survey, the proportion of vacant houses was high at 14 (42.4%). This study is conducting continuous rural housing research, rather than a temporary study on rural housing and vacant houses, based on the problems that have been drawn from previous research and existing fact-finding studies.

• 한국정밀공학회지
• /
• 제12권11호
• /
• pp.98-109
• /
• 1995

An investigation was performed to study the inner damage of laminated composite plates subjected to out-of-plane load. During the investigation, inpact velocity and equivalent static load relationship was derived. Reddy's higher-order shear deformation theory(HSDT) and Hashin's failure criteria were used to determine inner stresses and damaged area. And impact testing was carried out on laminated composite plates by air gun type impact testing machine. The CFRP specimens were composed of [ .+-. 45 .deg. ]$_{4}$and [ .+-. 45 .deg. /0 .deg. /90 .deg. ]$_{2}$ stacking sequences with 0.75$^{t}$ * 26$^{w}$ * 100$^{l}$ (mm) dimension. After impact testing. As a result, a relationship holds between damaged area and impact energy, and a matrix cracking was caused by the interlaminar shear stress in the middle ply and was caused by the inplane transverse stress in the bottom ply.

• 한국의류학회지
• /
• 제47권6호
• /
• pp.1080-1095
• /
• 2023

Three-dimensional virtual fitting has become a trending practice in the fashion industry because of its productivity benefits, allowing garments to be virtually worn by avatar models without physical production. This study analyzed the variables influencing clothing pressure in both real and virtual fittings to expand the potential utility of pressure data derived from the latter. For this purpose, six sets of compression garments were created by combining two types of tricot fabrics and three types of reduced-pattern tops, with the clothing for real and virtual fittings having identical dimensions. Focus was directed to analyzing the correlation among clothing pressure, surface area deformation, and the mechanical properties of the fabrics. In real fittings, clothing pressure was influenced by multiple factors, including garment design, pattern reduction ratio, body shape, and fabric properties, consistent with existing knowledge. In virtual fittings, however, only the digital mechanical characteristics of the fabrics significantly influenced clothing pressure. The findings suggest that a more reliable implementation of clothing pressure in virtual fitting programs necessitates an approach that considers the complex structural information of garments.

• 암석학회지
• /
• 제6권3호
• /
• pp.224-259
• /
• 1997

북부 소백산육괴의 중남부에 위치하는 장군봉지역(본 연구지역)은 선캠브리아대 변성퇴적암류(원남층과 율리층)와 고생대 변성퇴적암류[조선누층군(장산규암, 두음리층, 장군석회암)과 평안층군(동수곡층과 재산층)] 그리고 중생대 화강암류(춘양화강암) 등으로 구성되어 있다. 본 논문은 장군봉지역에서 북부 소백산육괴의 지질구조를 해석하기위해 구성암류의 암석구조와 미세구조를 연구하였다. 그 결과 연구지역의 지질구조는 선캠브리아대 원남층의 편마면(S0)과 고생대 변성퇴적암류의 층리면(SO)이 형성된 이후 적어도 네 번의 변형단계(D2 연성전단변형 이전에 한 번의 습곡작용과 D2 연성전단변형 이후에 적어도 두 번의 습곡작용)를 거쳐 형성되었음을 알게 되었다. 첫 번째 변형(D1 변현)은 동-서 방향의 준 수평적인 습곡축(L1)과 동-서 주향에 북쪽으로 고각 경사하는 습곡축면(S1)을 갖는 밀착 등사습곡(tight isoclinal fold) (F1 습곡)을 형성시켰다. 두 번째 변형(D2 변형)은 전단엽리면(S2)의 상부가 동쪽으로 이동한 전단감각(top-to-the east shear sense)을 보이는 우수 주향 이동성 대규모 연성전단운동 발생기로서 이러한 D2 연성전단변형에 의해 신장선구조(L2)가 S2 전단엽리면상에 형성된다. 세 번째 변형(D3 변형)은 도-서 방향의 준 수평적인 습곡축(L3)과 동-서 주향에 북쪽으로 저각 내지 중각 경사하는 습곡축면(S3)을 갖는 열린 경사습곡(open inclined fold) (F3 습곡)을 형성시켰다. 그 결과 원래 북쪽으로 경사하는 S1 엽리면은 F3 습곡의 한쪽 날개부에서 남쪽으로 경사하게 되고, 원래의 D2 전단감각은 재 배열된 남쪽 경사 S1 엽리면상에서 상부가 서쪽으로 이동한 전단감각을 보이게 된다. 네 번째 변형(D4 변형)은 북북서 내지 북서 방향으로 침강하는 습곡축(L4)과 남서 방향으로 경사하는 습곡축면(S4)을 갖는 북동 버전스의 비대칭형 열린 경사습곡(F4 습곡)을 형성시켰다. 그 결과 동-서 방향성을 보이는 D4 변형 이전의 구조요소들은 부분적으로 남-북 방향성으로 재배열된다. 이러한 변형의 효과는 고생대 변성퇴적암류에서 주로 인지된다.

• Bulletin of the Korean Chemical Society
• /
• 제2권3호
• /
• pp.96-104
• /
• 1981

(1) The flow data of f (stress) and ${\dot{s}$ (strain rate) for Fe and Ti alloys were plotted in the form of f vs. -ln ${\dot{s}$ by using the literature values. (2) The plot showed two distinct patterns A and B; Pattern A is a straight line with a negative slope, and Pattern B is a curve of concave upward. (3) According to Kim and Ree's generalized theory of plastic deformation, pattern A & B belong to Case 1 and 2, respectively; in Case 1, only one kind of flow units acts in the deformation, and in Case 2, two kinds flow units act, and stress is expressed by $f={X_1f_1}+{X_2f_2}$where $f_1\;and\;f_2$ are the stresses acting on the flow units of kind 1 and 2, respectively, and $X_1,\;X_2$ are the fractions of the surface area occupied by the two kinds of flow units; $f_j=(1/{\alpha}_j) sinh^{-1}\;{\beta}_j{{\dot{s}}\;(j=1\;or\;2)$, where $1/{\alpha}_j\;and\;{\beta}_j$ are proportional to the shear modulus and relaxation time, respectively. (4) We found that grain-boundary flow units only act in the deformation of Fe and Ti alloys whereas dislocation flow units do not show any appreciable contribution. (5) The deformations of Fe and Ti alloys belong generally to pattern A (Case 1) and B (Case 2), respectively. (6) By applying the equations, f=$(1/{\alpha}_{g1}) sinh^-1({\beta}_{g1}{\dot{s}}$) and $f=(X_{g1}/{\alpha}_{g1})sinh^{-1}({\beta}_{g1}{\dot{s}})+ (X_{g2}/{\alpha}_{g2})\;shih^{-1}({\beta}_{g2}{\dot{s}})$ to the flow data of Fe and Ti alloys, the parametric values of $x_{gj}/{\alpha}_{gj}\;and\;{\beta}_{gs}(j=1\;or\;2)$ were determined, here the subscript g signifies a grain-boundary flow unit. (7) From the values of ($({\beta}_gj)^{-1}$) at different temperatures, the activation enthalpy ${\Delta}H_{gj}^{\neq}$ of deformation due to flow unit gj was determined, ($({\beta}_gj)^{-1}$) being proportional to , the jumping frequency (the rate constant) of flow unit gj. The ${\Delta}H_{gj}\;^{\neq}$ agreed very well with ${\Delta}H_{gj}\;^{\neq}$ (self-diff) of the element j whose diffusion in the sample is a critical step for the deformation as proposed by Kim-Ree's theory (Refer to Tables 3 and 4). (8) The fact, ${\Delta}H_{gj}\;^{\neq}={\Delta}H_{j}\;^{\neq}$ (self-diff), justifies the Kim-Ree theory and their method for determining activation enthalpies for deformation. (9) A linear relation between ${\beta}^{-1}$ and carbon content [C] in hot-rolled steel was observed, i.e., In ${\beta}^{-1}$ = -50.2 [C] - 40.3. This equation explains very well the experimental facts observed with regard to the deformation of hot-rolled steel..

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(I)
• /
• pp.307-310
• /
• 2005

The effects of deformation properties on the bond of steel reinforcing bars to concrete are experimentally studies to expect the lap splice strength. Based on the previous research about relative rib area, lap splice strength between reinforcing bars and concrete can be improved by the control of rib height and spacing. This paper describes the testing and analysis of 15 beam-spliced specimens containing D25, D22, D19 with relative rib areas ranging from 0.066 to 0.162. The tests are analyzed to determine the effect of relative rib area(Rr) on the increase in bond strength. The tests also provide a preliminary indication of the effect of high relative rib area on the splice strength of uncoated bars.