• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.582-590
• /
• 2010

Garment design needs an iterative manipulation of 2D patterns to generate a final sloper. Traditionally there have been two kinds of design methodologies such as the flat pattern method and the pattern draping method. But today, it is possible to combine the advantages from the two methods due to the realistic cloth simulation techniques. We devised a new garment design system which starts from 3D initial drape simulation result and then modifies the garment by editing the 2D flat patterns synchronously. With this interactive methodology using real-time pattern deformation technique, the designer can freely change a pattern shape by watching its 3D outlook in real-time. Also the final garment data were given relative coordinates with respect to the human anthropometric feature points detected by an automatic body feature detection algorithm. Using the relative human body coordinate system, the final garments can be re-used to an arbitrary body data without repositioning in the drape simulation. A female shirt was used for an example and a 3D body scan data was used for an illustration of the feature point detection algorithm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.4
• /
• pp.303-309
• /
• 2008

Dense and fine polymer patterns often collapse, as they come into contact with each other at their protruding tips. Resist pattern collapse depends on the aspect ratio of patterns and the surface tension of rinsing materials. The pattern collapse is a very serious problem in microfabrication, because it is one of the factors which limit the device dimensions. The reasons for the pattern collapse are known as the surface tension of rinse liquid, centrifugal force and rinse liquid flow produced in the developing process. In this work, we tried to evaluate the pattern collapse of three-dimensional microstructures that were fabricated by two-photon induced photopolymerization, and showed the way how to reduce the deformation of microstructures.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.61-68
• /
• 2000

In general, the design of membrane structures takes three steps. The first is shape finding analysis which is determination of initial equilibrium geometry with uniform stresses. The second step involve the computation of the stress-deformation to get completed membrane under various load conditions. The third step is to divide the membrane structures into several plan strips from the initial equilibrium states. This procedure is needed because of the initial shape has usually undevelopable curved surface and is called as "cutting patterns generation". By introducing this work, the deformation due to the initial stress is removed and approximate cutting patterns are generated. In this approach, however, material properties is not considered, therefore the error between the design stresses and actual stresses during the fabrication of plan strips should be occurred. In this paper, actual equilibrium shape analysis procedure for HP shape models is presented. The deviations of stresses between the design stresses and actual stresses are estimated.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.1
• /
• pp.16-24
• /
• 1992

Moire interferometry using a diffraction grating and a laser is a powerful technique for analizing small deformation of a specimen. In the method, the x and y-directional fringe patterns are obtained by using the x and y-directional sets of two beams. If the both sets of two beams are simultaneously incident to the specimen, the x and y-directional fringe patterns are super imposed. In this case, it is difficult to separate each directional fringe pattern. Therefore each fringe pattern has been separately recorded by selecting each set of two beams. In order to analyze a two-dimensional strain changing with time, Moire interferometry using the two-dimensional fourier transform method is proposed and the x and y-directional fringes are separated. By this method, the thermal deformation of a glass plate is analyzed.

• Design & Manufacturing
• /
• v.12 no.2
• /
• pp.5-10
• /
• 2018

Vacuum-assisted thermoforming is one of the critical steps for successful application of film insert molding(FIM) to parts of complex shape. In this study, the simulations and experiments of thermoforming processes were performed to investigate the effects of process conditions on thickness distribution and printed pattern deformation of films in vacuum-assisted thermoforming. The film thickness uniformity increased with decreasing film heating time, whereas it increased with increasing vacuum delay time. After thermoforming of films with uniform pattern space of 5mm, the maximum space was 9.432mm. Based on the simulation, a modified pattern was calculated to obtain uniform spaces after thermoforming. In the experiments for film with the modified pattern, the maximum space appeared 5.837mm. In, addition. the predicted patterns were in good agreement with the experimental results.

• Korean Journal of Remote Sensing
• /
• v.21 no.3
• /
• pp.221-228
• /
• 2005

Baekdusan is a Cenozoic stratovolcano in which a series of micro-seismic events and gaseous emissions have been reported in 1990s. Two-pass DInSAR technique was applied to determine displacement in the volcano by using 10 ERS SAR and 41 JERS-1 SAR datasets. Most interferometric phases out of 58 JERS-1 differential interferograms showed concentric fringe patterns that correlated with elevation. From an analysis of fringe-duration relation, the fringe patterns were found to be severely distorted specifically by stratified troposphere. To estimate the tropospheric delay, we used the data in the Sobaeksan located about 20 km away from the summit of Baekdusan. The maximum and mean magnitudes of the phase delay in the Baekdusan were respectively 13.8 cm and 3.8 cm over 1200 m in altitude. After removing tropospheric effects, a mean inflation rate was estimated to be about 3 mm per year from 1992 to 1998. Although the inflation rate of the volcano is inconclusive without ground truth data, the results indicate that there exists slow upward deformation in the Baekdusan volcano.

• Steel and Composite Structures
• /
• v.42 no.5
• /
• pp.711-722
• /
• 2022

In this paper, hyperbolic shear deformation plate theory is developed for thermal buckling of functionally graded plates with porosity by dividing transverse displacement into bending and shear parts. The present theory is variationally consistent, and accounts for a quadratic variation of the transverse shearstrains across the thickness and satisfies the zero traction boundary conditions on the top and bottom surfaces of the plate without using shear correction factors. Three different patterns of porosity distributions (including even and uneven distribution patterns, and the logarithmic-uneven pattern) are considered. The logarithmic-uneven porosities for first time is mentioned. Equilibrium and stability equations are derived based on the present theory. The non-linear governing equations are solved for plates subjected to simply supported boundary conditions. The thermal loads are assumed to be uniform, linear and non-linear distribution through-the-thickness. A comprehensive parametric study is carried out to assess the effects of volume fraction index, porosity fraction index, aspect ratio and side-to-thickness ratio on the buckling temperature difference of imperfect FG plates.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.448-451
• /
• 2005

An aspheric mirror, which requires less than $\lambda/2\;(\lambda=632.8nm)$ of form error for the $\phi$ 200mm reference curved surface, has been manufactured with an ultra-precision turning machine. We have known through several tests that the deformation patterns of the reflecting surface is related with bolting positions. In this paper the effect of main factors on deformation of a reflector is studied with a FE code. The considered factors are angular velocity, natural frequencies for a mirror, temperature increment during machining. The obtained test results are similar to the deformation shape due to the assumed temperature increment.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.09a
• /
• pp.114-122
• /
• 2002

The ASCE formula of lifeline.soil interaction force is the basis of semi-analytical relationship for buried pipelines subjected to longitudinal permanent ground deformation due to seismic induced liquefaction. However, since the ASCE formula has been developed based on the stiffness of non-liquefied region, it is needed to modify for the varied stiffness of liquefied region. With this object, the consideration of decreasing effect of soil stiffness in liquefied region is made: i.e. the spatial distributions of pipeline-soil interaction force in liquefied region. It means that the improved formula can reflect various patterns of permanent ground deformation more realistically. Through the comparative analyses using both the improved and ASCE formula, the applicability of the improved and the limitation of the ASCE formula and semi-analytical relationship are discussed. Also, relative influences of various parameters are evaluated for the clarification of behavior of pipeline subjected to longitudinal permanent ground deformation due to liquefaction.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.2
• /
• pp.103-110
• /
• 2011

A two-dimensional immiscible droplet deformation phenomena on moving wall in a channel has been investigated by using lattice Boltzmann method involving two-phase model. The dependence of the deformation of the droplet with different sizes on the contact angle and the velocity of bottom wall has studied. When the bottom wall starts to move, the deformation of the droplet occurs. For the largest bottom wall velocity, eventually, the deformation of the droplet is classified into the three patterns according to the contact angle.